2005-2008 Yaris · Service Manual ENGINE

ECM Power Source Circuit

Circuit diagnosis · Vehicles built from Aug 2005

DESCRIPTION

When the ignition switch is turned on (IG), the battery voltage is applied to the IGSW terminal of the ECM. The input signal to the MREL terminal of the ECM causes a current to flow to the EFI relay coil, closing the EFI relay contacts and supplying power to terminals +B and +B1 of the ECM.

WIRING DIAGRAM

A116132E01

INSPECTION PROCEDURE

NOTICE:
Perform electronic throttle learning after replacing the ECM (Click here).


1. INSPECT INTEGRATION RELAY
A107914E02
  1. Remove the integration relay from the engine room relay block.

  1. Measure the voltage between the terminal of the integration relay and body ground.

    Standard voltage:
    Tester Connection
    Specified Condition
    1C-1 - Body ground
    10 to 14 V

  1. Reinstall the integration relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (INTEGRATION RELAY - BATTERY)
OK


2. INSPECT INTEGRATION RELAY (EFI RELAY AND IG2 RELAY)
A107921E04
  1. Inspect the AM2 fuse and EFI fuse.

    1. Remove the AM2 fuse and EFI fuse.

    2. Check the fuse resistance.

      Standard resistance:
      Below 1 Ω

    3. Reinstall the fuses.

  1. Inspect the relay.

    1. Check the relay resistance.

      Standard resistance:
      Tester Connection
      Specified Condition
      1C-1 - 1B-4
      10 kΩ or higher
      1C-1 - 1B-4
      Below 1 Ω
      (When battery voltage applied to terminals 1B-2 and 1B-3)
      1C-1 - 1A-8
      10 kΩ or higher
      1C-1 - 1A-8
      Below 1 Ω
      (When battery voltage applied to terminals 1C-1 and 1A-7)



NG
REPLACE INTEGRATION RELAY
OK


3. CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY - ECM)
A116133E01
  1. Remove the integration relay from the engine room relay block.

  1. Disconnect the ECM connector.

  1. Check the resistance.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    MREL (A32-6) - Integration relay (1A-7)
    Below 1 Ω
    +B (A32-24) - Integration relay (1A-8)
    Below 1 Ω
    +B1 (A32-23) - Integration relay (1A-8)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    MREL (A32-6) - Body ground
    10 kΩ or higher
    +B (A32-24) - Body ground
    10 kΩ or higher
    +B1 (A32-23) - Body ground
    10 kΩ or higher

  1. Reinstall the integration relay.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
A116134E01
  1. Disconnect the ECM connector.

  1. Check the resistance.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    E1 (A32-1) - Body ground
    Below 1 Ω

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. INSPECT ECM (IGSW TERMINAL VOLTAGE)
A116134E03
  1. Disconnect the ECM connector.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage between the terminals of ECM connector.

    Standard voltage:
    Switch Condition
    Specified Condition
    IGSW (A32-4) - E1 (A32-1)
    10 to 14 V

  1. Reconnect the ECM connector.



OK
REPLACE ECM
NG


6. INSPECT FUSE (IGN FUSE)
A107935E03
  1. Remove the IGN fuse from the instrument panel junction block.

  1. Check the fuse resistance.

    Standard resistance:
    Below 1 Ω

  1. Reinstall the IGN fuse.



NG
CHECK FOR SHORT IN ALL HARNESS AND COMPONENTS CONNECTED TO FUSE
OK


7. CHECK HARNESS AND CONNECTOR (ECM - INTEGRATION RELAY)
A116133E04
  1. Remove the integration relay from the engine room relay block.

  1. Disconnect the ECM connector.

  1. Check the resistance.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    IGSW (A32-4) - Integration relay (1B-4)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    IGSW (A32-4) - Body ground
    10 kΩ or higher

  1. Reinstall the integration relay.

  1. Reconnect the ECM connector.

    Result:
    Result
    Proceed To
    Out of normal range
    A
    Within normal range (with Entry and Start System)
    B
    Within normal range (without Entry and Start System)
    C



B
Go to step 8

C
Go to step 9
A

REPAIR OR REPLACE HARNESS OR CONNECTOR

8. CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY - MAIN BODY ECU)
A116136E01
  1. Remove the integration relay from the engine room relay block.

  1. Remove the instrument panel junction block (main body ECU).

  1. Check the resistance.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    Integration relay (1B-2) - IG2D (D65-5)
    Below 1 Ω
    Integration relay (1B-3) - Body ground
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    IG2D (D65-5) - Body ground
    10 kΩ or higher

  1. Reinstall the integration relay.

  1. Reinstall the main body ECU.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CHECK ENTRY AND START SYSTEM

9. CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY - IGNITION SWITCH)
A116137E01
  1. Remove the integration relay from the engine room relay block.

  1. Disconnect the ignition or starter switch assembly connector.

  1. Check the resistance.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    Integration relay (1B-2) - Ignition or starter switch (D8-6)
    Below 1 Ω
    Integration relay (1B-3) - Body ground
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    Ignition or starter switch (D8-6) - Body ground
    10 kΩ or higher

  1. Reinstall the integration relay.

  1. Reconnect the ignition or starter switch assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


10. INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
A107906E03
  1. Remove the ignition or starter switch assembly.

  1. Measure the resistance between the terminals of ignition or starter switch assembly.

    Standard resistance:
    Switch Position
    Tester Connection
    Specified Condition
    LOCK
    -
    10 kΩ or higher
    ACC
    2 - 4
    Below 1 Ω
    ON
    1 - 2 - 4
    Below 1 Ω
    5 - 6
    Below 1 Ω
    START
    1 - 3 - 4
    Below 1 Ω
    5 - 6 - 7
    Below 1 Ω

  1. Reinstall the ignition or starter switch assembly.



NG
REPLACE IGNITION OR STARTER SWITCH ASSEMBLY
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNIITON SWITCH - BATTERY)


← U0101 Lost Communication with TCM (from Nov 2005)VC Output Circuit (from Aug 2005) →