INSTALLATION
Removal / installation · Vehicles built from Nov 2005
| 1. INSTALL ECM (w/ PTC HEATER) |
Install the ECM with the bolt and 2 nuts.

- Torque:
- 8.0 N*m{ 82 kgf*cm , 71 in.*lbf }
Install the 2 nuts and the water pipe.

- Torque:
- 9.8 N*m{ 100 kgf*cm , 87 in.*lbf }
Install the 2 bolts and the brake booster vacuum pipe.

- Torque:
- 9.8 N*m{ 100 kgf*cm , 87 in.*lbf }
Connect the 2 ECM connectors.

Install the 2 lock knobs and the harness clamp.
| 2. INSTALL ECM (for LHD) |
Install the ECM with the bolt and 2 nuts.

- Torque:
- 8.0 N*m{ 82 kgf*cm , 71 in.*lbf }
Connect the 2 ECM connectors.

Install the 2 lock knobs and the harness clamp.
| 3. INSTALL ECM (for RHD) |
Install the ECM with the bolt and 2 nuts.

- Torque:
- 8.0 N*m{ 82 kgf*cm , 71 in.*lbf }
Connect the 2 ECM connectors.

Install the 2 lock knobs and the harness clamp.
| 4. INSTALL COWL TOP PANEL OUTER |
![]() ![]() |
Install the cowl top panel outer with the 9 bolts.
- Torque:
- 6.5 N*m{ 66 kgf*cm , 58 in.*lbf }
Install the wire harness.
| 5. INSTALL COWL TO REGISTER DUCT SUB-ASSEMBLY NO. 2 |
![]() ![]() |
Engage the claws, and install cowl top register duct No. 2.
| 6. INSTALL FRONT WIPER MOTOR AND LINK ASSEMBLY |
![]() ![]() |
Connect the connector.
Slide the wiper link as shown in the illustration and engage the rubber pin with the body.
Install the front wiper motor and link with the 2 bolts.
- Torque:
- 5.5 N*m{ 56 kgf*cm , 49 in.*lbf }
| 7. INSTALL COWL TOP VENTILATOR LOUVER LH (for LHD) |
![]() ![]() |
Engage the 4 claws and install the cowl top ventilator louver LH.
Install the 2 clips.
| 8. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for LHD) |
![]() ![]() |
Connect the washer hose.
Engage the 11 claws and install the cowl top ventilator louver sub-assembly.

Install the clip.
Connect the washer hose.
Engage the 2 hooks and install cowl top ventilator louver center No. 1.

| 9. INSTALL COWL TOP VENTILATOR LOUVER LH (for RHD) |
![]() ![]() |
Engage the 10 claws and install the cowl top ventilator louver sub-assembly.
Install the clip.
Connect the washer hose.
| 10. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for RHD) |
![]() ![]() |
Engage the 10 claws and install the cowl top ventilator louver sub-assembly.
Install the clip.
Connect the washer hose.
| 11. INSTALL HOOD TO COWL TOP SEAL |
![]() ![]() |
Engage the 7 clips and install the hood to cowl top seal.
| 12. INSTALL FRONT WIPER ARM LH |
![]() ![]() |
Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).
Clean the wiper pivot serrations with a wire brush.
Operate the wiper, then stop the windshield wiper motor in the automatic stop position.
Align the blade tip with the mark on the windshield glass, as shown in the illustration.

Tighten the nut of the front wiper arm.
- Torque:
- 26 N*m{ 265 kgf*cm , 19 ft.*lbf }
| 13. INSTALL FRONT WIPER ARM RH |
![]() ![]() |
Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).
Clean the wiper pivot serrations with a wire brush.
Operate the wiper, then stop the windshield wiper motor in the automatic stop position.
Align the blade tip with the mark on the windshield glass, as shown in the illustration.

Tighten the nut of the front wiper arm.
- Torque:
- 26 N*m{ 265 kgf*cm , 19 ft.*lbf }
| 14. INSTALL FRONT WIPER ARM HEAD CAP |
![]() ![]() |
Engage the claw and install the 2 front wiper arm head caps.
| 15. INSTALL ENGINE COVER SUB-ASSEMBLY NO. 1 |
![]() ![]() |
Engage the 4 pins and install engine cover No. 1.
| 16. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
- Torque:
- 5.4 N*m{ 55 kgf*cm , 48 in.*lbf }










