2005-2008 Yaris · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built from Nov 2005


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

2. REMOVE ENGINE COVER SUB-ASSEMBLY NO. 1

A125743
  1. Disengage the 4 pins and remove engine cover No. 1.


3. REMOVE FRONT WIPER ARM HEAD CAP

E113848E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the claw and remove the 2 front wiper arm head caps.


4. REMOVE FRONT WIPER ARM LH
  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.

  1. E113850
    Remove the nut and front wiper arm.


5. REMOVE FRONT WIPER ARM RH

HINT:
Use the same procedure as for the LH side.


6. REMOVE HOOD TO COWL TOP SEAL

E113851
  1. Disengage the 7 clips and remove the hood to cowl top seal.


7. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for LHD)

E117641
  1. Disengage the 2 hooks and remove cowl top ventilator louver center No. 1.

  1. E113852
    Disconnect the washer hose.

  1. Disengage the 11 claws and clip.

  1. E113854
    Disconnect the washer hose and remove the cowl top ventilator louver sub-assembly.


8. REMOVE COWL TOP VENTILATOR LOUVER LH (for LHD)

E113853
  1. Remove the 2 clips.

  1. Disengage the 4 claws and remove the cowl top ventilator louver LH.


9. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for RHD)

E113855
  1. Disconnect the washer hose.

  1. Disengage the 10 claws and clip and remove the cowl top ventilator louver sub-assembly.


10. REMOVE COWL TOP VENTILATOR LOUVER LH (for RHD)

E113856
  1. Remove the clip.

  1. Disengage the 4 claws and remove the cowl top ventilator louver LH.


11. REMOVE FRONT WIPER MOTOR AND LINK ASSEMBLY

E113857
  1. Remove the 2 bolts.

  1. Slide the wiper link. Disengage the meshing of the rubber pin, then disconnect the connector and remove the front wiper motor and link.


12. REMOVE COWL TO REGISTER DUCT SUB-ASSEMBLY NO. 2

A118801E01
  1. Disengage the claws, and remove cowl top register duct No. 2.


13. REMOVE COWL TOP PANEL OUTER

A126332
  1. Separate the wire harness.

  1. Remove the 9 bolts and cowl top panel outer.


14. REMOVE ECM (W/ PTC HEATER)

  1. A128325
    Remove the 2 lock knobs and harness clamp.

  1. Disconnect the 2 ECM connectors.

  1. A118858
    Remove the 2 bolts and separate the brake booster vacuum pipe.

  1. A128327
    Remove the 2 nuts and separate the water pipe.

  1. A128326
    Remove the bolt, 2 nuts and the ECM.


15. REMOVE ECM (for LHD)

  1. A128325
    Remove the 2 lock knobs and harness clamp.

  1. Disconnect the 2 ECM connectors.

  1. A128326
    Remove the bolt, 2 nuts and the ECM.


16. REMOVE ECM (for RHD)

  1. A128335
    Remove the 2 lock knobs and harness clamp.

  1. Disconnect the 2 ECM connectors.

  1. A128332
    Remove the bolt, 2 nuts and the ECM.

← COMPONENTS (from Nov 2005)INSTALLATION (from Nov 2005) →