2005-2008 Yaris · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built from Nov 2005

NOTICE:
Always use "Torx" socket wrench E10 when removing the rear seat.


1. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Package Tray Trim)

  1. B114569E01
    Remove the 2 package tray trim suspenders.

  1. Remove the 5 pieces of hook tape.

  1. Disengage the 2 claws and remove the package tray trim.


2. REMOVE DECK BOARD SUB-ASSEMBLY (w/ Deck Board)

  1. B106371
    Release the 2 knobs and remove the deck board.


3. REMOVE SPARE WHEEL COVER ASSEMBLY (w/ Deck Board)

  1. B138393
    Remove the spare wheel cover.


4. REMOVE DECK FLOOR BOX (w/ Deck Board)

  1. B106373
    Release the 2 knobs and remove the deck floor box.


5. REMOVE REAR FLOOR CARPET ASSEMBLY (w/o Deck Board)

  1. B138392
    Remove the rear floor carpet.


6. REMOVE NO. 2 REAR SEAT LEG COVER

  1. B124330
    Disengage the 6 claws and remove the No. 2 rear seat leg cover.


7. REMOVE REAR SEAT ASSEMBLY

  1. B124331
    Using "Torx" socket wrench E10, remove the 3 bolts and pull up the rear seat cushion.

  1. B124315
    Using "Torx" socket wrench E10, remove the 4 bolts and the rear seat.


8. REMOVE REAR FLOOR SERVICE HOLE COVER

A118713
  1. Remove the clip from the floor carpet.

  1. A118728
    Remove the rear floor service hole cover.

  1. A127193
    Disconnect the fuel pump connector.


9. DISCHARGE FUEL SYSTEM PRESSURE
(Click here)

10. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

11. DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

A131359
  1. Widen the tip of the tube joint clip and pull out the clip.

  1. Pull out the fuel tank main tube to disconnect it.

    NOTICE:
    1. Keep the O-ring free of any foreign matter, as it becomes contaminated easily.
    2. Do not use any tools in this procedure.
    3. Do not forcefully bend or twist the tube.
    4. Put the tube in a plastic bag to prevent damage and contamination.
    5. If the fuel suction plate and tube are stuck together, pinch the tube and turn it carefully to disconnect it.
    6. Do not damage any clip. If a clip is damaged, replace it.


12. DISCONNECT NO. 2 FUEL EMISSION TUBE

A131360
  1. Loosen the clamp and disconnect No. 2 fuel emission tube.


13. DISCONNECT NO. 1 CANISTER OUTLET HOSE SUB-ASSEMBLY

A131361
  1. Disconnect the canister outlet hose.


14. REMOVE FUEL PUMP GAUGE RETAINER

A118736E01
  1. Using SST, remove the fuel pump gauge retainer.

    SST
    09808-14020   (09808-01410, 09808-01420, 09808-01430)

    HINT:
    Fit the rib on the fuel pump gauge retainer into the cutout the SST.


15. REMOVE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

A118739
  1. Remove the fuel suction with pump and gauge tube assembly.

    NOTICE:
    Do not bend the arm of the sender gauge.

  1. A118738
    Remove the fuel suction tube gasket from the fuel tank.


16. DRAIN FUEL

17. REMOVE NO. 4 FRONT FLOOR HEAT INSULATOR

A118749
  1. Remove the 2 nuts and remove front floor heat insulator No. 4.


18. REMOVE NO. 1 FUEL TANK PROTECTOR

A118750E03
  1. Pinch and remove the clip as shown in the illustration.

  1. Remove the bolt and the No. 1 fuel tank protector.


19. DISCONNECT FUEL TANK BREATHER HOSE

A135330
  1. Loosen the clamp bolt and disconnect the fuel tank breather hose.


20. DISCONNECT FUEL TANK TO FILLER PIPE HOSE

A135331
  1. Loosen the clamp and disconnect the fuel tank to filler pipe hose.


21. DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

A118743E02
  1. Release the lock as shown in the illustration, then pull and remove the fuel tank main tube.

    NOTICE:
    1. Remove any dirt and foreign matter from the clip before performing this work.
    2. Avoid any scratches or foreign matter on the parts when disconnecting, as the quick connector has the O-ring that seals the plug.
    3. Perform this work by hand. Do not use any tools.
    4. Do not forcibly bend, twist or turn the nylon tube.
    5. Protect the disconnected parts by covering them with a plastic bag.
    6. If the connector and pipe are stuck, disconnect the nylon tube by turning it by hand to release it.


22. DISCONNECT NO. 2 FUEL EMISSION TUBE

A118746
  1. Loosen the clamp and disconnect fuel emission tube No. 2.


23. REMOVE FUEL TANK ASSEMBLY

A118748
  1. Set a mission jack under the fuel tank.

  1. Remove the 4 bolts and the fuel tank.


24. REMOVE FUEL TANK MAIN TUBE SUB-ASSEMBLY

A135333
  1. Remove the fuel tank main tube from the fuel tank.


25. REMOVE NO. 2 FUEL EMISSION TUBE

A118747
  1. Remove fuel emission tube No. 2 from the fuel tank.

← COMPONENTS (from Nov 2005)INSTALLATION (from Nov 2005) →