2005-2008 Yaris · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built from Nov 2005

NOTICE:
Always use "Torx" socket wrench E10 when installing the rear seat.


1. INSTALL NO. 2 FUEL EMISSION TUBE

A118747
  1. Install fuel emission tube No. 2 onto the fuel tank.


2. INSTALL FUEL TANK MAIN TUBE SUB-ASSEMBLY

A135333
  1. Install the fuel tank main tube onto the fuel tank.


3. INSTALL FUEL TANK ASSEMBLY

A118748
  1. Clean the bolt holes and remove any grease.

  1. Install the fuel tank with 4 new bolts.

    Torque:
    14 N*m{ 146 kgf*cm , 10 ft.*lbf }


4. CONNECT NO. 2 FUEL EMISSION TUBE

A118745E01
  1. Connect fuel emission tube No. 2 with the clamp.


5. CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

A118744E02
  1. Align the fuel tube connector with the pipe, push the fuel tube connector in until the retainer makes a click sound, then lock the cover of the connector.

    NOTICE:
    1. Check that there are no scratches or foreign matter on the disconnected parts of the fuel tube connector and pipe before performing this work.
    2. After connecting, pull the pipe and fuel tube connector to make sure that they are securely connected.


6. CONNECT FUEL TANK TO FILLER PIPE HOSE

A135331
  1. Connect the fuel tank to filler pipe hose with the clamp.

  1. Tighten the clamp bolt.


7. CONNECT FUEL TANK BREATHER HOSE

A135330
  1. Connect the fuel tank breather hose with the clamp.

  1. Tighten the clamp bolt.


8. INSTALL FUEL TANK COVER VENT CASE

A118751
  1. Install the fuel tank cover vent case with the bolt and clip.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


9. INSTALL NO. 4 FRONT FLOOR HEAT INSULATOR

A118749
  1. Install front No. 4 floor heat insulator with the 2 nuts.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


10. INSTALL FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

A118738
  1. Install a new fuel suction tube gasket onto the fuel tank.

  1. A118740
    Align the protrusion of the fuel pump with the cutout of the fuel tank and install the fuel suction with pump and gauge tube assembly.

    NOTICE:
    The arm of the sender gauge should not be bent.


11. INSTALL FUEL PUMP GAUGE RETAINER
  1. Align the end of the threads of the fuel pump gauge retainer with that of the fuel tank.

  1. A118736E01
    Set SST to the fuel pump gauge retainer.
    SST
    09808-14020   (09808-01410, 09808-01420, 09808-01430)

    NOTICE:
    1. Use SST. Do not use any other tools such as a screwdriver.
    2. As the fuel pipes are located on the track of SST, SST should be reset a few times to prevent it from coming into contact with the pipes when installing the fuel pump gauge retainer.

    HINT:
    Fit the cutout of SST into the rib on the fuel pump gauge retainer.

  1. A118737E01
    While holding the fuel pump assembly by hand, use SST to tighten the fuel pump gauge retainer one and half turns so that the mark on the retainer is within the range indicated in the illustration.


12. CONNECT NO. 1 CANISTER OUTLET HOSE SUB-ASSEMBLY

A131361
  1. Connect the canister outlet hose.


13. CONNECT NO. 2 FUEL EMISSION TUBE

A131360
  1. Connect fuel emission tube No. 2.


14. CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

A131362E01
  1. Insert the fuel tank main tube.

  1. Install the tube joint clip.

    NOTICE:
    1. Check that there are no scratches or foreign matter on the connecting parts.
    2. Check that the fuel tube joint is inserted securely.
    3. Check that the fuel tube joint clip is on the collar of the fuel tube joint.
    4. After installing the tube joint clip, check that the fuel tube joint has not been pulled off.
    5. Do not damage any of the clips. If a clip is damaged, replace it.


15. ADD FUEL

16. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


17. CHECK FOR FUEL LEAK

  1. A127178E01
    When using the intelligent tester.

    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch on (IG) and the intelligent tester main switch ON.

      NOTICE:
      Do not start the engine.

    3. Select the Active Test mode on the intelligent tester.

      HINT:
      Refer to the intelligent tester operator's manual for further details.

  1. Check that there is no fuel leakage anywhere in the fuel system after doing maintenance.


18. INSTALL REAR FLOOR SERVICE HOLE COVER

A127193
  1. Connect the fuel pump connector.

  1. A118729E01
    Install the rear floor service hole cover with new butyl tape.


19. INSTALL REAR SEAT ASSEMBLY

  1. B124363E01
    Insert the 2 locating pins through the 2 body holes and install the rear seat.

  1. Using "Torx" socket wrench E10, install the 4 bolts in the sequence shown in the illustration.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }

  1. B124331E01
    Install the rear seat cushion.

  1. Using "Torx" socket wrench E10, install the 3 bolts in the sequence shown in the illustration.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }


20. INSTALL NO. 2 REAR SEAT LEG COVER

  1. B124330
    Engage the 6 claws and install the No. 2 rear seat leg cover.


21. INSTALL DECK FLOOR BOX (w/ Deck Board)

  1. B106445
    Install the deck floor box and lock the 2 knobs.


22. INSTALL SPARE WHEEL COVER ASSEMBLY (w/ Deck Board)

  1. B138393
    Install the spare wheel cover.


23. INSTALL DECK BOARD SUB-ASSEMBLY (w/ Deck Board)

  1. B106447
    Set the deck board and lock the 2 knobs.


24. INSTALL REAR FLOOR CARPET ASSEMBLY (w/o Deck Board)

  1. B138393
    Install the spare wheel cover.


25. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Package Tray Trim)

  1. B114569E01
    Engage the 2 claws and install the package tray trim panel.

  1. Install the 5 pieces of hook tape.

  1. Install the 2 package tray trim suspenders.

← REMOVAL (from Nov 2005)PRECAUTION (from Nov 2006) →