2005-2008 Yaris · Service Manual ENGINE

P0120 Throttle / Pedal Position Sensor / Switch "A" Circuit

Diagnostic trouble codes · Vehicles built from Nov 2005

Also covers:

CAUTION / NOTICE / HINT

HINT:
These DTCs relate to the Throttle Position (TP) sensor.


DESCRIPTION

The Throttle Position (TP) sensor is mounted on the throttle body assembly, and detects the opening angle of the throttle valve. This sensor is a non-contact type, and uses Hall-effect elements in order to yield accurate signals even under extreme driving conditions, such as at high speeds and very low speeds.
The TP sensor has two sensor circuits which each transmit a signal, VTA1 and VTA2. VTA1 is used to detect the throttle valve angle and VTA2 is used to detect malfunctions in VTA1. The sensor signal voltages vary between 0 V and 5 V in proportion to the throttle valve opening angle, and are transmitted to the VTA terminals of the ECM.
As the valve closes, the sensor output voltage decreases and as the valve opens, the sensor output voltage increases. The ECM calculates the throttle valve opening angle according to these signals and controls the throttle actuator in response to driver inputs. These signals are also used in calculations such as air-fuel ratio correction, power increase correction and fuel-cut control.
A122559E01
DTC No.
DTC Detection Conditions
Trouble Areas
P0120
Output voltage of VTA1 quickly fluctuates beyond lower and upper malfunction thresholds for 2 seconds when accelerator pedal depressed
(1 trip detection logic)
  1. Throttle Position (TP) sensor (built into throttle body assembly)
  2. ECM
P0122
Output voltage of VTA1 0.2 V or less for 2 seconds when accelerator pedal depressed
(1 trip detection logic)
  1. TP sensor (built into throttle body assembly)
  2. Short in VTA1 circuit
  3. Open in VC circuit
  4. ECM
P0123
Output voltage of VTA1 4.535 V or more for 2 seconds when accelerator pedal depressed
(1 trip detection logic)
  1. TP sensor (built into throttle body assembly)
  2. Open in VTA1 circuit
  3. Open in E2 circuit
  4. Short between VC and VTA1 circuits
  5. ECM
P0220
Output voltage of VTA2 quickly fluctuates beyond lower and upper malfunction thresholds for 2 seconds when accelerator pedal depressed
(1 trip detection logic)
  1. TP sensor (built into throttle body assembly)
  2. ECM
P0222
Output voltage of VTA2 1.75 V or less for 2 seconds when accelerator pedal depressed
(1 trip detection logic)
  1. TP sensor (built into throttle body assembly)
  2. Short in VTA2 circuit
  3. Open in VC circuit
  4. ECM
P0223
Output voltage of VTA2 4.8 V or more, and VTA1 between 0.2 V and 2.02 V, for 2 seconds when accelerator pedal depressed
(1 trip detection logic)
  1. TP sensor (built into throttle body assembly)
  2. Open in VTA2 circuit
  3. Open in E2 circuit
  4. Short between VC and VTA2 circuits
  5. ECM
P2135
Either condition (a) or (b) met (1 trip detection logic):
(a) Difference between output voltages of VTA1 and VTA2 0.02 V or less for 0.5 seconds or more
(b) Output voltage of VTA1 0.2 V or less, and VTA2 1.75 V or less, for 0.4 seconds or more
  1. Short between VTA1 and VTA2 circuits
  2. TP sensor (built into throttle body assembly)
  3. ECM

HINT:
  1. When any of these DTCs are set, check the throttle valve opening angle by selecting the following menu items on an intelligent tester: Powertrain / Engine and ECT / Data List / Throttle Position No. 1 and Throttle Position No. 2.
  1. Throttle Position No. 1 denotes the VTA1 signal, and Throttle Position No. 2 denotes the VTA2 signal.

    Reference (Normal Condition):
    Tester Display
    Accelerator Pedal Fully Released
    Accelerator Pedal Fully Depressed
    Throttle Position No. 1
    0.5 to 1.1 V
    3.3 to 4.9 V
    Throttle Position No. 2
    2.1 to 3.1 V
    4.6 to 5.0 V


FAIL-SAFE

When any of these DTCs, or other DTCs relating to ETCS (Electronic Throttle Control System) malfunctions, are set, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator off, and the throttle valve is returned to a 8° throttle angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing, in accordance with the accelerator pedal opening angle, to allow the vehicle to continue at a minimal speed. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly. Fail-safe mode continues until a pass condition is detected, and the ignition switch is then turned off.

WIRING DIAGRAM

A112574E05

INSPECTION PROCEDURE

HINT:
Read freeze frame data using an intelligent tester. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data, from the time the malfunction occurred.


1. READ VALUE USING INTELLIGENT TESTER (THROTTLE POSITION NO. 1 AND THROTTLE POSITION NO. 2)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Throttle Position No. 1 and Throttle Position No. 2.

  1. Read the values displayed on the tester.

    Result:
    TP No. 1 (VTA1)
    When Accelerator Pedal Released
    TP No. 2 (VTA2)
    When Accelerator Pedal Released
    TP No. 1 (VTA1)
    When Accelerator Pedal Depressed
    TP No. 2 (VTA2)
    When Accelerator Pedal Depressed
    Trouble Areas
    Proceed To
    0 V to 0.2 V
    0 V to 0.2 V
    0 V to 0.2 V
    0 V to 0.2 V
    VC circuit open
    A
    4.5 V to 5.0 V
    4.5 V to 5.0 V
    4.5 V to 5.0 V
    4.5 V to 5.0 V
    E2 circuit open
    0 V to 0.2 V,
    or 4.5 V to 5.0 V
    2.4 V to 3.4 V
    (Fail-safe)
    0 V to 0.2 V,
    or 4.5 V to 5.0 V
    2.4 V to 3.4 V
    (Fail-safe)
    VTA1 circuit open or ground short
    0.7 V to 1.3 V
    (Fail-safe)
    0 V to 0.2 V,
    or 4.5 V to 5.0 V
    0.7 V to 1.3 V
    (Fail-safe)
    0 V to 0.2 V,
    or 4.5 V to 5.0 V
    VTA2 circuit open or ground short
    0.5 V to 1.1 V
    2.1 V to 3.1 V
    3.3 V to 4.9 V
    (Not fail-safe)
    4.6 V to 5.0 V
    (Not fail-safe)
    TP sensor circuit normal
    B

HINT:
TP No. 1 denotes Throttle Position No. 1 , and TP No. 2 denotes Throttle Position No. 2.



B
Go to step 5
A


2. CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM)
A107944E05
  1. Disconnect the C17 throttle body connector.

  1. Disconnect the C20 ECM connector.

  1. Check the resistance.

    Standard resistance (Check for open):
    Tester Connections
    Specified Conditions
    VC (C17-5) - VCTA (C20-67)
    Below 1 Ω
    VTA (C17-6) - VTA1 (C20-115)
    VTA2 (C17-4) - VTA2 (C20-114)
    E2 (C17-3) - ETA (C20-91)

    Standard resistance (Check for short):
    Tester Connections
    Specified Conditions
    VC (C17-5) or VCTA (C20-67) - Body ground
    10 kΩ or higher
    VTA (C17-6) or VTA1 (C20-115) - Body ground
    VTA2 (C17-4) or VTA2 (C20-114) - Body ground

  1. Reconnect the throttle body connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. INSPECT ECM (VC VOLTAGE)
A107895E05
  1. Disconnect the C17 throttle body connector.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage between the terminals of the throttle body connector.

    Standard voltage:
    Tester Connections
    Specified Conditions
    VC (C17-5) - E2 (C17-3)
    4.5 to 5.5 V

  1. Reconnect the throttle body connector.



NG
REPLACE ECM
OK


4. REPLACE THROTTLE BODY ASSEMBLY

NEXT


5. CHECK WHETHER DTC OUTPUT RECURS (THROTTLE POSITION SENSOR DTCS)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester on.

  1. Clear DTCs (Click here).

  1. Start the engine.

  1. Allow the engine to idle for 15 seconds or more.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result:
    Display (DTC Output)
    Proceed To
    P0120, P0122, P0123, P0220, P0222, P0223, and/or P2135
    A
    No output
    B



B
SYSTEM OK
A

REPLACE ECM


← P0116 Engine Coolant Temperature Circuit Range / Performance Problem (from Nov 2005)P0121 Throttle / Pedal Position Sensor / Switch "A" Circuit Range / Performance Problem (from Nov 2005) →