2005-2008 Yaris · Service Manual RESTRAINTS

INSTALLATION

Removal / installation · Vehicles built from Jan 2006

CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (Click here).

HINT:
The procedure described below is for the RH side. Use the same procedure for both the RH and LH sides, unless otherwise specified.


1. INSTALL FRONT SHOULDER BELT ANCHOR ADJUSTER ASSEMBLY

  1. B134898
    Insert the hook into the body hole and install the shoulder belt anchor adjuster with the 2 bolts.

    Torque:
    42 N*m{ 430 kgf*cm , 31 ft.*lbf }


2. INSTALL SHOULDER BELT ANCHORAGE PLATE COVER

  1. B134897
    Engage the 2 claws and install the shoulder belt anchorage plate cover.


3. INSTALL CENTER PILLAR UPPER GARNISH

  1. B134768
    Engage the 2 hooks and 2 clips and install the center pillar upper garnish.


4. INSTALL FRONT SEAT OUTER BELT ASSEMBLY

  1. B114426E01
    Check the angle of inclination required to lock the retractor.

    1. Gently incline the retractor from its initial position. Check that the belt does not lock when the retractor is inclined 15 ° or less in any direction. Also, check that the belt locks when the inclination of the retractor is 45 ° or more.

      NOTICE:
      Do not disassemble the retractor.

      If the operation is not as specified, replace the front seat outer belt.

  1. B134896E01
    Hook the lower stay of the retractor onto the 2 body hooks and provisionally install the retractor with the 2 bolts.

  1. Tighten bolt A and then bolt B.

    Torque:
    4.9 N*m{ 50 kgf*cm , 43 in.*lbf } for bolt A
    42 N*m{ 430 kgf*cm , 31 ft.*lbf } for bolt B

  1. B134894E01
    Connect the pretensioner connector.

    1. Connect the pretensioner connector.

    2. Lock the locking button.

      NOTICE:
      Securely lock the locking button.

  1. B114296
    Install the shoulder anchor with the bolt.

    Torque:
    42 N*m{ 430 kgf*cm , 31 ft.*lbf }

  1. B134892
    Install the floor anchor with the bolt.

    Torque:
    42 N*m{ 430 kgf*cm , 31 ft.*lbf }

  1. Check that the ELR locks.

    NOTICE:
    1. The check should be performed with the front seat outer belt installed.
    2. Do not allow the anchor part of the front seat outer belt and the protruding parts of the floor panel to overlap.


    1. With the belt installed, check that the belt locks when it is pulled out quickly.
      If the operation is not as specified, replace the front seat outer belt.


5. INSTALL LAP BELT OUTER ANCHOR COVER

  1. B134891
    Engage the 3 claws and install the lap belt outer anchor cover.


6. INSTALL SEAT BELT ANCHOR COVER CAP

  1. B114428
    Engage the 3 claws and install the seat belt anchor cover cap.


7. INSTALL CENTER PILLAR LOWER GARNISH

  1. B134767
    Engage the 2 clips and 3 claws and install the center pillar lower garnish.


8. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP

  1. B138446
    Install the rear door opening trim weatherstrip.


9. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP

  1. B138445
    Install the front door opening trim weatherstrip.


10. INSTALL REAR DOOR SCUFF PLATE

  1. B134771
    Engage the 7 claws and install the rear door scuff plate.


11. INSTALL FRONT DOOR SCUFF PLATE

  1. B134764
    Engage the 11 claws and install the front door scuff plate.


12. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


13. INSPECT SRS WARNING LIGHT
(Click here)
← REMOVAL (from Jan 2006)DISPOSAL (from Jan 2006) →