2005-2008 Yaris · Service Manual STEERING

INSTALLATION

Removal / installation · Vehicles built from Jan 2006


1. INSTALL STEERING COLUMN ASSEMBLY

  1. C139089
    Install the steering column assembly onto the instrument panel reinforcement assembly with the bolt and 2 nuts.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

  1. Connect all the connectors and clamp the wire harnesses onto the steering post assembly bracket.


2. INSTALL BRAKE PEDAL (for Automatic Transaxle)
  1. Apply MP grease No. 2 to the brake master cylinder push rod clevis pin and installation surfaces.

  1. Install the 2 brake pedal bushes, and install the brake pedal with the nut and brake pedal shaft.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }

  1. C119065
    Apply MP grease No. 2 to the brake master cylinder push rod clevis pin and installation surfaces.

  1. Connect the brake master cylinder push rod clevis to the brake pedal with the brake master cylinder push rod clevis pin, install the clip onto the brake master cylinder push rod clevis pin, and then install the brake pedal return spring.


3. INSTALL BRAKE PEDAL SUPPORT SUB-ASSEMBLY (for Manual Transaxle)

C116881
  1. Install the pedal support with the bolt and 4 nuts.

    Torque:
    Bolt:
    24 N*m{ 241 kgf*cm , 17 ft.*lbf }
    Nut:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }


4. INSTALL BRAKE MASTER CYLINDER PUSH ROD CLEVIS (for Manual Transaxle)
  1. Apply lithium soap base glycol grease to the push rod pin.

  1. C116880
    Install the push rod clevis with the push rod pin and clip.

  1. Install the brake pedal return spring.


5. INSTALL NO.2 STEERING INTERMEDIATE SHAFT ASSEMBLY

  1. G028410E01
    Connect all the connectors and clamp the wire harnesses onto the steering post assembly bracket.

  1. Align the matchmarks on No. 2 steering intermediate shaft assembly and the steering sliding yoke and provisionally install them with bolt C.

    Torque:
    28 N*m{ 290 kgf*cm , 21 ft.*lbf }

  1. Align the matchmarks on the steering sliding yoke and steering gear assembly and install them with bolt B.

    Torque:
    28 N*m{ 290 kgf*cm , 21 ft.*lbf }

  1. Tighten bolt A.

    Torque:
    28 N*m{ 290 kgf*cm , 21 ft.*lbf }


6. INSTALL COLUMN HOLE COVER SILENCER SHEET

  1. A116501
    Install the column hole cover plate with the 2 clips.

  1. Install the floor carpet.


7. INSTALL INSTRUMENT PANEL UNDER TRAY

B132333
  1. Engage the 6 claws and install the instrument panel under tray.

  1. Install the 2 <A> screws.

  1. B132390
    Engage the 4 claws and install the instrument panel under tray.


8. INSTALL POWER STEERING ECU

  1. C117192
    Connect the 2 steering post assembly connectors to the power steering ECU.

  1. Install the power steering motor harness and torque sensor wire harness clamps onto the side of the power steering ECU.

  1. Tilt the steering post assembly up and down to make sure that the power steering motor harness and torque sensor wire harness do not interfere with any components.


9. INSTALL UPPER INSTRUMENT PANEL SUB-ASSEMBLY

B130309E01
  1. Using a nipper, cut off both ends of the runner portion shown in the illustration (When installing a new one).

  1. Engage the 5 claws at the front side of the instrument panel.

  1. Engage the 7 clips at the rear side of the instrument panel.

    B132324

  1. Install the upper instrument panel with the 2 <C> bolts and the 2 <B> screws.

    B132323E01

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf } for bolt <C>

  1. B132386
    Connect the passenger airbag connector and clamp.


10. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY

B132321E01
  1. Engage the claws of the hinge portions by pushing the glove compartment door in the horizontal direction to install the glove compartment door assembly.

    NOTICE:
    Engage the claw by pushing it in the horizontal direction, otherwise, installation failure caused by excessive play around the hinge portion will result.

  1. B132319E01
    Slightly flex the upper portion of the glove compartment door assembly to engage the stopper.

  1. Install the glove compartment door stopper onto the glove compartment door.


11. INSTALL FRONT PILLAR GARNISH RH

  1. B138439E01
    w/ Curtain Shield Airbag:

    1. Remove the piece of cloth or nylon.

  1. B134787
    Install the 3 clamps.

  1. Connect the antenna connector.

  1. B134781E01
    w/ Curtain Shield Airbag:

    1. Install a new special clip and the clip onto the front pillar garnish.

    2. Engage the 2 clips and the 2 claws and install the front pillar garnish.

  1. B134779
    w/o Curtain Shield Airbag:

    1. Engage the 2 clips and the 2 claws and install the front pillar garnish.


12. INSTALL FRONT PILLAR GARNISH LH

  1. B138440
    w/ Curtain Shield Airbag:

    1. Remove the piece of cloth or nylon.

  1. B134789
    Install the 4 clamps.

  1. B134782E01
    w/ Curtain Shield Airbag:

    1. Install a new special clip and the clip onto the front pillar garnish.

    2. Engage the 2 clips and the 2 claws and install the front pillar garnish.

  1. B134780
    w/o Curtain Shield Airbag:

    1. Engage the 2 clips and the 2 claws and install the front pillar garnish.


13. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH
  1. Install the front door opening trim weatherstrip.


14. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH
  1. Install the front door opening trim weatherstrip.


15. INSTALL COMBINATION METER ASSEMBLY

E116835E01
  1. Install the combination meter assembly with the 2 screws.

    NOTICE:
    Install the combination meter so that the rib of the combination meter is held between the instrument panel and the instrument cluster finish panel.

  1. Connect the 2 connectors.


16. INSTALL INSTRUMENT CLUSTER FINISH PANEL

E116833
  1. Fit the 2 claws of the instrument cluster finish panel into the upper instrument cluster finish panel center.

  1. E116834
    Engage the 5 claws and 5 clips and install the instrument cluster finish panel.


17. INSTALL INSTRUMENT PANEL FINISH PANEL END RH

B132318
  1. Engage the 6 claws and 3 clips and install the instrument panel finish panel end RH.


18. INSTALL INSTRUMENT PANEL FINISH PANEL END LH

B132317
  1. Engage the 6 claws and 3 clips and install the instrument panel finish panel end LH.


19. INSTALL INSTRUMENT PANEL FINISH PANEL LOWER CENTER

B132316
  1. Engage the 2 claws and 2 clips and install the instrument panel finish panel lower center.


20. INSTALL COMBINATION SWITCH ASSEMBLY

  1. C139088
    Install the turn signal switch assembly with spiral cable onto the steering post assembly with the clamp.

  1. Connect all the connectors to the turn signal switch with spiral cable.


21. INSTALL STEERING COLUMN COVER

  1. C139094E01
    Engage the claw to install the steering column upper cover.

  1. C139093E01
    Engage the 2 claws to install the steering column lower cover.

  1. Install the 3 screws.


22. INSTALL STEERING WHEEL ASSEMBLY

  1. C139086E01
    Align the matchmarks and install the steering wheel assembly onto the steering column assembly.

  1. Install the nut.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }

  1. Connect all connectors to the spiral cable.


23. INSTALL STEERING PAD

C139082
  1. Using "Torx" socket wrench T30, loosen the 2 bolts completely.

  1. Pull the steering pad toward you.

  1. C139084E01
    Using a thin-bladed screwdriver, release the locking button.

  1. Using a thin-bladed screwdriver, disconnect the 2 connectors.

  1. Detach the horn terminal.


24. POSITION FRONT WHEELS FACING STRAIGHT AHEAD

25. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


26. CHECK SRS WARNING LIGHT
(Click here)

27. PERFORM CALIBRATION OF TORQUE SENSOR ZERO POINT
(Click here)
← REASSEMBLY (from Jan 2006)COMPONENTS (from Aug 2005) →