2005-2008 Yaris · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built from Nov 2006


1. INSTALL TIMING CHAIN OR BELT COVER OIL SEAL

A157500E02
  1. Using SST and a hammer, tap in a new oil seal until its surface is flush with the timing chain cover edge.

    SST
    09223-22010  

    NOTICE:
    1. Do not tap the oil seal at an angle.
    2. Keep the lip free of foreign matter.

    HINT:
    The pressing-in depth should be within the range of -1 mm and 1 mm from the chain cover edge.

  1. Apply MP grease to the oil seal lip.


2. INSTALL CRANKSHAFT PULLEY
  1. Align the pulley set key with the key groove of the pulley.

  1. A150861E02
    Using SST, hold the pulley in place and tighten the bolt.
    SST
    09213-54015   (91651-60855)
    09330-00021  

    Torque:
    190 N*m{ 1940 kgf*cm , 140 ft.*lbf }


3. INSTALL FAN AND GENERATOR V BELT
  1. Provisionally install the fan and generator V belt onto each pulley.

    NOTICE:
    Make sure that the V belt is securely fitted into the rib groove of the pulley.


4. ADJUST FAN AND GENERATOR V BELT

  1. A161127E01
    Turn adjusting bolt C and adjust the tension of the V belt.

    NOTICE:
    Check that bolt D is tightened to the specified torque of 19 N*m (189 kgf*cm, 14 ft.*lbf).

  1. Tighten fixing bolts A and B.

    Torque:
    19 N*m{ 189 kgf*cm , 14 ft.*lbf } for bolt A
    43 N*m{ 438 kgf*cm , 32 ft.*lbf } for bolt B


5. INSPECT FAN AND GENERATOR V BELT

  1. A147660E02
    Check the V belt deflection and tension.

    Deflection:
    Item
    Specified Condition
    New belt
    7.5 to 8.6 mm (0.296 to 0.338 in.)
    Used belt
    8.0 to 10.0 mm (0.315 to 0.397 in.)

    Tension:
    Item
    Specified Condition
    New belt
    688 to 884 N (70 to 90 kg, 155 to 199 ld)
    Used belt
    402 to 598 N (40 to 61 kg, 90 to 134 ld)

    If the belt deflection is not as specified, adjust it.

    HINT:
    1. Check the V belt deflection at the specified point.
    2. When installing a new belt, set its tension to the specified value.
    3. When inspecting a belt which has been used for over 5 minutes, apply the Used Belt specifications.
    4. When reinstalling a belt which has been used for over 5 minutes, adjust its deflection and tension to the intermediate values of the Used Belt specifications.
    5. V belt tension and deflection should be checked after 2 revolutions of engine cranking.
    6. When checking the tension, use a sonic tension meter.

    Input Data for Sonic Tension Meter

    Weight:
    15 g/rib*m

    Width:
    6 ribs (21.36 mm)

    Span:
    188 mm (w/ A/C)
    282 mm (w/o A/C)


6. INSTALL NO. 2 CYLINDER HEAD COVER

  1. A158207
    Disengage the 4 fittings shown and install the No. 2 cylinder head cover by applying pressure to it.

    HINT:
    Make sure that the oil and the engine oil level dipstick are correctly installed before installing the No. 2 cylinder head cover.


7. INSPECT FOR ENGINE OIL LEAK

8. INSTALL ENGINE UNDER COVER RH
← REMOVAL (from Nov 2006)COMPONENTS (from Nov 2006) →