2005-2008 Yaris · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built from Nov 2006


1. INSTALL ENGINE REAR OIL SEAL

  1. A156258E01
    Using SST and a hammer, evenly tap the oil seal until its surface is flush with the rear oil seal retainer edge.
    SST
    09223-15030  
    09950-70010   (09951-07100)

    NOTICE:
    1. Keep the lip free from foreign materials.
    2. Do not tap on the oil seal at an angle.

    HINT:
    The pressing-in depth should be within the range of -1 mm and 1 mm from the rear oil seal retainer edge.

  1. Apply MP grease to a new oil seal lip.

    NOTICE:
    Wipe off extra grease on the crankshaft.


2. INSTALL FLYWHEEL SUB-ASSEMBLY

  1. A156219E02
    Hold the crankshaft with SST.
    SST
    09213-54015   (91651-60855)
    09330-00021  

  1. Clean the 8 bolts and their holes.

  1. A057108E01
    Apply adhesive to the 2 or 3 end threads of the bolts.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent.

  1. A157841E01
    Install the flywheel with the 8 bolts in the order shown in the illustration.

    Torque:
    49 N*m{ 500 kgf*cm , 38 ft.*lbf }

  1. A157844E01
    Mark paint marks on the upper edge of the bolt heads.

  1. Tighten the bolts 90° in the sequence order shown in the illustration.

    NOTICE:
    Do not start the engine for at least 1 hour after performing the installation.


3. INSTALL CLUTCH DISC ASSEMBLY

D029848E03
  1. Insert SST into the clutch disc assembly, then insert them both into the flywheel sub-assembly.

    SST
    09301-00110  

    NOTICE:
    Insert clutch disc assembly in the correct direction.


4. INSTALL CLUTCH COVER ASSEMBLY

D026323E03
  1. Align the matchmark on the clutch cover assembly with that on the flywheel sub-assembly.

  1. Following the procedures shown in the illustration, tighten the 6 bolts in order, starting with the bolt located near the knock pin at the top.

    Torque:
    19 N*m{ 195 kgf*cm , 14 ft.*lbf }

    HINT:
    1. Following the order in the illustration, tighten the bolts evenly one at a time.
    2. Move SST up and down, right and left lightly after checking that the disc is in the center, and tighten the bolts.

    SST
    09301-00110  


5. INSPECT AND ADJUST CLUTCH COVER ASSEMBLY

C062961
  1. Using a dial indicator with a roller instrument, check the diaphragm spring tip alignment.

    Maximum non-alignment:
    0.5 mm (0.020 in.)

  1. D029849E01
    If the alignment is not as specified, using SST, adjust the diaphragm spring tip alignment.
    SST
    09333-00013  


6. INSTALL MANUAL TRANSAXLE ASSEMBLY

C063143
  1. Align the input shaft with the clutch disc and install the manual transaxle onto the engine.

  1. Install the 7 bolts.

    Torque:
    33 N*m{ 336 kgf*cm , 24 ft.*lbf }


7. INSTALL TRANSVERSE ENGINE ENGINE MOUNTING BRACKET

C152812
  1. Install the engine mounting bracket LH with the 6 bolts.

    Torque:
    64 N*m{ 653 kgf*cm , 47 ft.*lbf }


8. INSTALL TRANSVERSE ENGINE ENGINE MOUNTING INSULATOR

C106372
  1. Install the engine mounting insulator LH with the 5 bolts.

    Torque:
    52 N*m{ 530 kgf*cm , 38 ft.*lbf }

  1. Install the engine mounting bracket LH and engine insulator LH with the bolt and nut.

    Torque:
    52 N*m{ 530 kgf*cm , 38 ft.*lbf }


9. INSTALL TRANSVERSE ENGINE ENGINE MOUNTING CONTROL BRACKET

C116856
  1. Install the engine mounting control bracket with the 4 bolts.

    Torque:
    64 N*m{ 653 kgf*cm , 47 ft.*lbf }


10. INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY
  1. Support the front suspension crossmember with a transmission jack.

  1. A108973E02
    Provisionally install the front suspension crossmember onto the body with the 6 bolts.
    Bolt
    Underhead Length (mm)
    A
    38
    B
    99
    C
    41

  1. By inserting SST into the datum holes in the front suspension crossmembers RH and LH alternately, tighten bolts A, B and C on both sides to the specified torque, in several steps.

    SST
    09670-00011  

    Torque:
    70 N*m{ 714 kgf*cm , 52 ft.*lbf } for Bolt A
    160 N*m{ 1,631 kgf*cm , 118 ft.*lbf } for Bolt B
    95 N*m{ 969 kgf*cm , 70 ft.*lbf } for Bolt C

    NOTICE:
    1. Insert SST into the datum hole in a vertical orientation.
    2. If SST can not be inserted into the datum hole vertically, loosen all the bolts and then insert SST again.


    A109226E01

  1. C107979E01
    Install the engine moving control rod with the bolt.

    Torque:
    120 N*m{ 1,224 kgf*cm , 89 ft.*lbf }


11. INSTALL FRONT DRIVE SHAFT ASSEMBLY LH
  1. Coat the spline of the inboard joint with gear oil.

  1. C116899
    Align the inboard joint splines and install the drive shaft with a screwdriver and hammer.

    NOTICE:
    1. Face the cut area of the front drive shaft hole snap ring downward.
    2. Do not damage the oil seal.
    3. Do not damage the inboard joint boot.

    HINT:
    Confirm whether the drive shaft is securely driven in by checking the reaction force and sound.


12. INSTALL FRONT DRIVE SHAFT ASSEMBLY RH

HINT:
The installation procedure for the RH side is the same as that for the LH side.


13. INSTALL FRONT AXLE ASSEMBLY LH
  1. Push the front axle out of the vehicle to align the spline of the drive shaft with the front axle and insert the front axle.

    NOTICE:
    1. Do not push the front axle further out of the vehicle than is necessary.
    2. Do not damage the outboard joint boot.
    3. Check for any foreign matter on the speed sensor rotor and insertion part.
    4. Do not damage the speed sensor rotor.


14. INSTALL FRONT AXLE ASSEMBLY RH

HINT:
The installation procedure for the RH side is the same as that for the LH side.


15. INSTALL FRONT STABILIZER LINK ASSEMBLY LH

  1. C106044
    Install the stabilizer link with the nut.

    Torque:
    74 N*m{ 755 kgf*cm , 55 ft.*lbf }

    HINT:
    If the ball joint turns together with the nut, use a socket hexagon wrench 6 to hold the stud.


16. INSTALL FRONT STABILIZER LINK ASSEMBLY RH

HINT:
The installation procedure for the RH side is the same as that for the LH side.


17. INSTALL TIE ROD END SUB-ASSEMBLY LH

  1. C107961
    Install the tie rod end onto the steering knuckle with a new castle nut.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }

    NOTICE:
    If the holes for the clip are not aligned, tighten the nut by a further turn of up to 60°.

  1. Install a new cotter pin.


18. INSTALL TIE ROD END SUB-ASSEMBLY RH

HINT:
The installation procedure for the RH side is the same as that for the LH side.


19. INSTALL FRONT LOWER SUSPENSION ARM SUB-ASSEMBLY LH

  1. C107513
    Install the lower arm onto the steering knuckle with a new castle nut.

    Torque:
    98 N*m{ 1000 kgf*cm , 72 ft.*lbf }

    NOTICE:
    If the holes for the clip are not aligned, tighten the nut by a further turn of up to 60°.

  1. Install a new clip.


20. INSTALL FRONT LOWER SUSPENSION ARM SUB-ASSEMBLY RH

HINT:
The installation procedure for the RH side is the same as that for the LH side.


21. INSTALL FRONT SPEED SENSOR LH

C112274
  1. Install the speed sensor onto the steering knuckle with the bolt.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

    NOTICE:
    1. Check that the speed sensor tip and installation portion are free of foreign matter.
    2. Install the speed sensor without turning it from its original installation angle.

  1. C125274
    Install the flexible hose and speed sensor with the bolt.

    Torque:
    29 N*m{ 300 kgf*cm , 22 ft.*lbf }

    NOTICE:
    Install the flexible hose and speed sensor without twisting them.


22. INSTALL FRONT SPEED SENSOR RH

HINT:
The installation procedure for the RH side is the same as that for the LH side.


23. INSTALL FRONT AXLE HUB NUT LH

C057566
  1. Using a 30 mm socket wrench, install a new axle hub nut.

    Torque:
    216 N*m{ 2203 kgf*cm , 160 ft.*lbf }

  1. Using a chisel and hammer, caulk the axle hub nut.


24. INSTALL FRONT AXLE HUB NUT RH

HINT:
The installation procedure for the RH side is the same as that for the LH side.


25. INSTALL STARTER ASSEMBLY

  1. A159355
    Install the starter assembly with the 2 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

  1. A159354
    Connect the connector.

  1. Connect terminal 30 with the nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. Close the terminal cap.


26. CONNECT CONNECTOR
  1. Connect the back-up light switch connector.


27. CONNECT WIRE HARNESS

C108079
  1. Connect the wire harness with the bolt.

    Torque:
    26 N*m{ 260 kgf*cm , 19 ft.*lbf }


28. INSTALL CONTROL CABLE BRACKET

C106374
  1. Install the control cable bracket with the 2 bolts.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }


29. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

C115305
  1. Connect the 2 cable ends and install the 2 washers and the 2 clips.

  1. Install 2 new clips onto the control cable bracket.


30. INSTALL CLUTCH RELEASE CYLINDER ASSEMBLY

C106371E01
  1. Install the clutch release cylinder and clutch pipe with the 4 bolts.

    Torque:
    12 N*m{ 120 kgf*cm , 8.7 ft.*lbf } for bolt A
    12 N*m{ 122 kgf*cm , 8.9 ft.*lbf } for bolt B


31. INSTALL BATTERY CARRIER

C106370
  1. Install the battery carrier with the 5 bolts.

    Torque:
    17 N*m{ 175 kgf*cm , 13 ft.*lbf }


32. INSTALL BATTERY TRAY

33. INSTALL BATTERY

34. INSTALL BATTERY CLAMP SUB-ASSEMBLY

35. INSTALL AIR CLEANER BRACKET

C106369
  1. Install the air cleaner bracket with the 2 bolts.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }


36. INSTALL AIR CLEANER ASSEMBLY

A104895
  1. Install the air cleaner case with air cleaner inlet with the 2 bolts.

    Torque:
    7.8 N*m{ 80 kgf*cm , 69 in.*lbf }

  1. Connect the wire harness to the air cleaner case.

  1. Install the air cleaner element.

  1. A147547
    Install and lock the air cleaner cap with air cleaner hose and then tighten the air cleaner hose clamp.

    Torque:
    3.0 N*m{ 31 kgf*cm , 27 in.*lbf }

  1. Connect the ventilation hose to the air cleaner hose.

  1. Connect the intake air flow meter connector and wire harness clamp.


37. INSTALL NO. 2 CYLINDER HEAD COVER

  1. A158207
    Disengage the 4 fittings shown and install the No. 2 cylinder head cover by applying pressure to it.

    HINT:
    Make sure that the oil and the engine oil level dipstick are correctly installed before installing the No. 2 cylinder head cover.


38. INSTALL COWL TOP PANEL OUTER

A115392
  1. Install the cowl top panel with the 9 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }

  1. A108438
    Connect the wire harness clamp.


39. INSTALL NO. 2 COWL TO REGISTER DUCT SUB-ASSEMBLY

A108437
  1. Engage the claw to install No. 2 cowl to register duct.


40. INSTALL WINDSHIELD WIPER MOTOR AND LINK

E113861
  1. Connect the connector.

  1. Slide the wiper link as shown in the illustration and engage the rubber pin with the body.

  1. Install the front wiper motor and link with the 2 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }


41. INSTALL COWL TOP VENTILATOR LOUVER LH (for LHD)

E113853
  1. Engage the 4 claws and install the cowl top ventilator louver LH.

  1. Install the 2 clips.


42. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for LHD)

E113854
  1. Connect the washer hose.

  1. E113852
    Engage the 11 claws and install the cowl top ventilator louver sub-assembly.

  1. Install the clip.

  1. Connect the washer hose.

  1. E117641
    Engage the 2 hooks and install cowl top ventilator louver center No. 1.


43. INSTALL COWL TOP VENTILATOR LOUVER LH (for RHD)

E113856
  1. Engage the 4 claws and install the cowl top ventilator louver LH.

  1. Install the clip.


44. INSPECT COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for RHD)

E113855
  1. Engage the 10 claws and install the cowl top ventilator louver sub-assembly.

  1. Install the clip.

  1. Connect the washer hose.


45. INSTALL HOOD TO COWL TOP SEAL

E113851
  1. Engage the 7 clips and install the hood to cowl top seal.


46. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH

E058837E10
  1. Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.

  1. E113862E01
    Align the blade tip with the mark on the windshield glass, as shown in the illustration.

  1. Tighten the nut of the front wiper arm.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }


47. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH

E058837E10
  1. Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.

  1. E113863E01
    Align the blade tip with the mark on the windshield glass, as shown in the illustration.

  1. Tighten the nut of the front wiper arm.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }


48. INSTALL HOOD SUB-ASSEMBLY

49. INSPECT HOOD SUB-ASSEMBLY

  1. Check that the clearance measurements are within the standard ranges.

    B118065E01

    Standard:
    Area
    Measurement
    Area
    Measurement
    A
    1.7 to 5.7 mm
    (0.067 to 0.224 in.)
    G
    -1.55 to 2.45 mm
    (-0.061 to 0.096 in.)
    B
    -2 to 2 mm
    (-0.079 to 0.079 in.)
    H
    1.75 to 5.75 mm
    (0.067 to 0.226 in.)
    C
    4.45 to 10.45 mm
    (0.175 to 0.411 in.)
    I
    -1.25 to 2.75 mm
    (-0.049 to 0.108 in.)
    D
    -0.95 to 5.05 mm
    (-0.037 to 0.199 in.)
    J
    -1.5 to 1.5 mm
    (-0.059 to 0.059 in.)
    E
    7.55 to 13.55 mm
    (0.297 to 0.533 in.)
    K
    2.0 to 5.0 mm
    (0.079 to 0.197 in.)
    F
    1.65 to 5.65 mm
    (0.065 to 0.222 in.)
    -
    -


50. ADJUST HOOD SUB-ASSEMBLY

  1. B106963
    Loosen the hood side hinge bolts.

  1. Move the hood to adjust the clearance to within the standard range.

  1. Tighten the hood side hinge bolts after the adjustment.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }

  1. B106965
    Adjust the height of the hood front end by turning the cushion rubber.

    HINT:
    The cushion rubber can be raised and lowered by turning it.

  1. B106964
    Adjust the hood lock.

    1. Loosen the 3 bolts.

    2. Adjust the hood lock position so that the striker can enter it smoothly.

    3. Tighten the 3 bolts after the adjustment.

      Torque:
      7.5 N*m{ 76 kgf*cm , 66 in.*lbf }


51. ADD TRANSAXLE OIL

52. INSPECT AND ADJUST TRANSAXLE OIL

D025304E01
  1. Stop the vehicle in a level place.

  1. Remove the transmission filler plug and the gasket.

  1. Check that the oil surface is within 5 mm (0.20 in.) of the bottom of the transmission filler plug opening.

    NOTICE:
    1. Excessively large or small amounts of oil may cause problems.
    2. After replacing the oil, drive the vehicle and check the oil level again.

  1. Check for oil leakage when the oil level is low.

  1. Install the transmission filler plug and a new gasket.

    Torque:
    39 N*m{ 400 kgf*cm , 29 ft.*lbf }


53. INSTALL FRONT WHEELS

54. INSTALL STEERING SLIDING YOKE SUB-ASSEMBLY

C118005E03
  1. Align the matchmarks and install the sliding yoke onto the intermediate shaft.

    Torque:
    28 N*m{ 290 kgf*cm , 21 ft.*lbf }

  1. Tighten bolt A.

    Torque:
    28 N*m{ 290 kgf*cm , 21 ft.*lbf }


55. INSTALL COLUMN HOLE COVER SILENCER SHEET

A116501
  1. Install the column hole cover silencer sheet with the 2 clips.

  1. Install the floor carpet.


56. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


57. INSPECT ABS SPEED SENSOR SIGNAL

58. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT
(Click here)

59. INSPECT FOR EXHAUST GAS LEAK

60. INSPECT FOR TRANSAXLE OIL LEAK

61. INSTALL ENGINE UNDER COVER RH

62. INSTALL ENGINE UNDER COVER LH
← REMOVAL (from Nov 2006)COMPONENTS (from Nov 2006) →