2005-2008 Yaris · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built from Nov 2006


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

2. REMOVE COLUMN HOLE COVER SILENCER SHEET

  1. A116501
    Remove the floor carpet and 2 clips and remove the column hole cover silencer.


3. REMOVE STEERING SLIDING YOKE SUB-ASSEMBLY

  1. C117212
    Use a seat belt to fix the steering wheel assembly, in order to avoid breakage of the spiral cable.

  1. C118005E03
    Place matchmarks on the sliding yoke of the steering intermediate shaft assembly and the power steering.

  1. Loosen bolt A, remove bolt B and separate the steering intermediate shaft assembly.


4. REMOVE FRONT WHEELS

5. REMOVE ENGINE UNDER COVER LH

6. REMOVE ENGINE UNDER COVER RH

7. DRAIN TRANSAXLE OIL
  1. Remove the filler plug and the gasket.

  1. Remove the drain plug and gasket, and then drain the manual transaxle oil.

  1. Install a new gasket and the drain plug.

    Torque:
    39 N*m{ 400 kgf*cm , 29 ft.*lbf }


8. REMOVE HOOD SUB-ASSEMBLY

9. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH
  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.

  1. E113850
    Remove the nut and front wiper arm.


10. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.


11. REMOVE HOOD TO COWL TOP SEAL

E113851
  1. Disengage the 7 clips and remove the hood to cowl top seal.


12. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for LHD)

E117641
  1. Disengage the 2 hooks and remove cowl top ventilator louver center No. 1.

  1. E113852
    Disconnect the washer hose.

  1. Disengage the 11 claws and clip.

  1. E113854
    Disconnect the washer hose and remove the cowl top ventilator louver sub-assembly.


13. REMOVE COWL TOP VENTILATOR LOUVER LH (for LHD)

E113853
  1. Remove the 2 clips.

  1. Disengage the 4 claws and remove the cowl top ventilator louver LH.


14. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for RHD)

E113855
  1. Disconnect the washer hose.

  1. Disengage the 10 claws and clip and remove the cowl top ventilator louver sub-assembly.


15. REMOVE COWL TOP VENTILATOR LOUVER LH (for RHD)

E113856
  1. Remove the clip.

  1. Disengage the 4 claws and remove the cowl top ventilator louver LH.


16. REMOVE WINDSHIELD WIPER MOTOR AND LINK

E113857
  1. Remove the 2 bolts.

  1. Slide the wiper link. Disengage the meshing of the rubber pin, then disconnect the connector and remove the front wiper motor and link.


17. REMOVE NO. 2 COWL TO REGISTER DUCT SUB-ASSEMBLY

A108437
  1. Disengage the claw and remove the No. 2 cowl to register duct sub-assembly.


18. REMOVE COWL TOP PANEL OUTER

A108438
  1. Disengage the wire harness clamp.

  1. A115392
    Remove the 9 bolts and remove the cowl top panel outer.


19. REMOVE NO. 2 CYLINDER HEAD COVER

  1. A163755
    Disengage the 2 fittings shown in the illustration.

  1. A163756
    Disengage the 2 fittings shown in the illustration, then remove the No. 2 cylinder head cover.


20. REMOVE AIR CLEANER ASSEMBLY

A147547E01
  1. Separate the intake air flow meter connector and wire harness clamp.

  1. Separate the ventilation hose from the air cleaner hose.

  1. Unfasten the 2 clamps.

  1. Remove the air cleaner cap sub-assembly with air cleaner hose.

  1. Remove the air cleaner element.

  1. A104895
    Separate the wire harness clamp from the air cleaner case.

  1. Remove the 2 bolts and remove the air cleaner case with air cleaner inlet.


21. REMOVE AIR CLEANER BRACKET

C106369
  1. Remove the 2 bolts and the air cleaner bracket.


22. REMOVE BATTERY CLAMP SUB-ASSEMBLY

23. REMOVE BATTERY

24. REMOVE BATTERY TRAY

25. REMOVE BATTERY CARRIER

C106370
  1. Remove the 5 bolts and the battery carrier.


26. SEPARATE CLUTCH RELEASE CYLINDER ASSEMBLY

C106371
  1. Remove the 4 bolts, then separate the clutch release cylinder.

    HINT:
    Suspend the clutch release cylinder with a piece of rope so as not to overload the clutch pipe.


27. SEPARATE TRANSMISSION CONTROL CABLE ASSEMBLY

C115305
  1. Remove the 2 clips and the 2 washers, and disconnect the 2 cables from the transaxle.

  1. Remove the 2 clips and disconnect the 2 cables from the control cable bracket.


28. REMOVE CONTROL CABLE BRACKET

C106374
  1. Remove the 2 bolts and the control cable bracket.


29. DISCONNECT WIRE HARNESS

C108079
  1. Remove the bolt, then disconnect the wire harness.


30. DISCONNECT CONNECTOR
  1. Disconnect the back-up light switch connector.


31. REMOVE STARTER ASSEMBLY

  1. A159354
    Remove the terminal cap.

  1. Remove the nut and disconnect terminal 30.

  1. Disconnect the connector.

  1. A159355
    Remove the 2 bolts and remove the starter assembly.


32. REMOVE FRONT AXLE HUB NUT LH

C085629E01
  1. Using SST and a hammer, release the staked part of the axle hub nut.

    SST
    09930-00010  

    NOTICE:
    1. Insert SST into the groove with the flat surface facing up.
    2. Do not damage the tip of SST using grinders.
    3. Completely unstake the staked part before removing the axle hub nut.
    4. Do not damage the threads of the drive shaft.

  1. Using a 30 mm socket wrench, remove the axle hub nut.


33. REMOVE FRONT AXLE HUB NUT RH

HINT:
The removal procedure for the RH side is the same as that for the LH side.


34. SEPARATE FRONT SPEED SENSOR LH

C125274
  1. Remove the bolt and separate the speed sensor and flexible hose.

  1. C112274
    Remove the bolt and separate the speed sensor from the steering knuckle.

    NOTICE:
    1. Keep the speed sensor tip and installation portion free of foreign matter.
    2. Remove the speed sensor without turning it from its original installation angle.


35. SEPARATE FRONT SPEED SENSOR RH

HINT:
The separation procedure for the RH side is the same as that for the LH side.


36. SEPARATE FRONT LOWER SUSPENSION ARM SUB-ASSEMBLY LH

C107513
  1. Remove the clip and castle nut.

  1. C107514E01
    Using SST, separate the lower arm.
    SST
    09628-00011  

    NOTICE:
    1. Do not damage the lower ball joint dust cover.
    2. Suspend SST with a piece of string or the equivalent.


37. SEPARATE FRONT LOWER SUSPENSION ARM SUB-ASSEMBLY RH

HINT:
The separation procedure for the RH side is the same as that for the LH side.


38. SEPARATE TIE ROD END SUB-ASSEMBLY LH
  1. Remove the cotter pin and castle nut.

  1. C116895E01
    Using SST, separate the tie rod end from the steering knuckle.
    SST
    09628-62011  

    NOTICE:
    Do not damage the tie rod end dust cover.


39. SEPARATE TIE ROD END SUB-ASSEMBLY RH

HINT:
The separation procedure for the RH side is the same as that for the LH side.


40. SEPARATE FRONT STABILIZER LINK ASSEMBLY LH

C106044
  1. Remove the nut and separate the stabilizer link from the shock absorber.

    HINT:
    If the ball joint turns together with the nut, use a socket hexagon wrench 6 to hold the stud.


41. SEPARATE FRONT STABILIZER LINK ASSEMBLY RH

HINT:
The separation procedure for the RH side is the same as that for the LH side.


42. SEPARATE FRONT AXLE ASSEMBLY LH

C085629E01
  1. Using SST and a hammer, release the staked part of the axle hub nut.

    SST
    09930-00010  

    NOTICE:
    1. Insert SST into the groove with the flat surface facing up.
    2. Do not damage the tip of SST using grinders.
    3. Completely unstake the staked part before removing the axle hub nut.
    4. Do not damage the threads of the drive shaft.

  1. Using a 30 mm socket wrench, remove the axle hub nut.


43. SEPARATE FRONT AXLE ASSEMBLY RH

HINT:
The separation procedure for the RH side is the same as that for the LH side.


44. REMOVE FRONT DRIVE SHAFT ASSEMBLY LH

C107924
  1. Using SST, remove the drive shaft.

    SST
    09520-01010  
    09520-24010   (09520-32040)

    NOTICE:
    1. Do not damage the oil seal.
    2. Do not damage the inboard joint boot.
    3. Do not drop the drive shaft.


45. REMOVE FRONT DRIVE SHAFT ASSEMBLY RH

C116896
  1. Using a screwdriver and hammer, remove the drive shaft.

    NOTICE:
    1. Do not damage the oil seal.
    2. Do not damage the inboard joint boot.
    3. Do not drop the drive shaft.


46. SUSPEND ENGINE ASSEMBLY

C152814
  1. Install the 2 hangers in the correct direction.

  1. Attach the engine chain hoist to the hangers.

    CAUTION:
    Do not attempt to hang the engine by hooking the chain to any other part.

    Parts No.:
    Engine Hanger No. 1: 12281-37020
    Engine Hanger No. 2: 12282-37010

    Bolt:
    91552-81050

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }


47. REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

  1. C107979
    Remove the bolt and separate the engine moving control rod.

  1. Support the front suspension crossmember with a transmission jack.

  1. C107982
    Remove the 6 bolts and remove the suspension crossmember.


48. REMOVE TRANSVERSE ENGINE ENGINE MOUNTING CONTROL BRACKET

C116856
  1. Remove the 4 bolts and the engine mounting control bracket.


49. SUPPORT MANUAL TRANSAXLE ASSEMBLY

50. REMOVE TRANSVERSE ENGINE ENGINE MOUNTING INSULATOR

C106372
  1. Remove the bolt and nut, then separate the engine mounting insulator LH.

  1. Remove the 5 bolts and the engine mounting insulator LH.


51. REMOVE TRANSVERSE ENGINE ENGINE MOUNTING BRACKET

C152812
  1. Remove the 6 bolts and the engine mounting bracket LH.


52. REMOVE MANUAL TRANSAXLE ASSEMBLY

C063143
  1. Remove the 7 bolts and the manual transaxle.


53. REMOVE CLUTCH COVER ASSEMBLY

D025280E04
  1. Put the matchmarks on the clutch cover assembly and the flywheel.

  1. Loosen each set bolt one turn at a time until the spring tension is released.

  1. Remove the set bolts and pull off the clutch cover.

    NOTICE:
    Do not drop the clutch disc.


54. REMOVE CLUTCH DISC ASSEMBLY

55. REMOVE FLYWHEEL SUB-ASSEMBLY

  1. A156219E02
    Hold the crankshaft with SST.
    SST
    09213-54015   (91651-60855)
    09330-00021  

  1. A157843
    Remove the 8 bolts and remove the flywheel sub-assembly.


56. REMOVE ENGINE REAR OIL SEAL

A156257E01
  1. Using a knife, cut off the oil seal lip.

  1. Using a screwdriver with its tip taped, pry out the oil seal.

    NOTICE:
    After removing the oil seal, check the crankshaft for damage. If it is damaged, smooth the surface with 400-grit sandpaper.

← COMPONENTS (from Nov 2006)INSTALLATION (from Nov 2006) →