2005-2008 Yaris · Service Manual ENGINE

REPLACEMENT

Removal / installation · Vehicles built from Nov 2006


1. REPLACE INTAKE VALVE GUIDE BUSH
  1. Heat the cylinder head to between 80 and 100°C (176 to 212°F).

  1. Place the cylinder head on wooden blocks.

  1. A150967E01
    Using SST and a hammer, tap out the guide bush.
    SST
    09201-10000   (09201-01050)
    09950-70010   (09951-07100)

  1. A152649
    Using a caliper gauge, measure the bush bore diameter of the cylinder head.

    Cylinder bore diameter:
    10.285 to 10.306 mm (0.4049 to 0.4057 in.)

    Select a new guide bush (STD or O/S 0.05):
    Bush Size
    Bush Bore Diameter
    STD
    10.285 to 10.306 mm (0.4049 to 0.4057 in.)
    O/S 0.05
    10.335 to 10.356 mm (0.4069 to 0.4077 in.)

    If the bush bore diameter of the cylinder head is greater than 10.306 mm (0.4057 in.), machine the bush bore to the dimension of 10.335 to 10.356 mm (0.4069 to 0.4077 in.) to install an O/S 0.05 valve guide bush. If the bush bore diameter of the cylinder head is greater than 10.356 mm (0.4077 in.), replace the cylinder head.

  1. Heat the cylinder head to 80 to 100°C (176 to 212°F).

  1. Place the cylinder head on wooden blocks.

  1. A150969E01
    Using SST and a hammer, tap in a new guide bush to the specified protrusion height.
    SST
    09201-10000   (09201-01050)
    09950-70010   (09951-07100)

    Protrusion height:
    9.9 to 10.3 mm (0.3898 to 0.4055 in.)

  1. A150971
    Using a sharp 5.5 mm reamer, ream the guide bush to obtain the standard specified clearance between the guide bush and valve stem.

    Standard oil clearance:
    0.025 to 0.060 mm (0.0010 to 0.0024 in.)


2. REPLACE EXHAUST VALVE GUIDE BUSH
  1. Heat the cylinder head to between 80 and 100°C (176 to 212°F).

  1. Place the cylinder head on wooden blocks.

  1. A150968E01
    Using SST and a hammer, tap out the guide bush.
    SST
    09201-10000   (09201-01050)
    09950-70010   (09951-07100)

  1. A152650
    Using a caliper gauge, measure the bush bore diameter of the cylinder head.

    Diameter:
    10.285 to 10.306 mm (0.4049 to 0.4057 in.)

    Select a new guide bush (STD or O/S 0.05):
    Bush Size
    Bush Bore Diameter
    STD
    10.285 to 10.306 mm (0.4049 to 0.4057 in.)
    O/S 0.05
    10.335 to 10.356 mm (0.4069 to 0.4077 in.)

    If the bush bore diameter of the cylinder head is greater than 10.306 mm (0.4057 in.), machine the bush bore to the dimension of 10.335 to 10.356 mm (0.4069 to 0.4077 in.) to install an O/S 0.05 valve guide bush. If the bush bore diameter of the cylinder head is greater than 10.356 mm (0.4077 in.), replace the cylinder head.

  1. Heat the cylinder head to between 80 and 100°C (176 to 212°F).

  1. Place the cylinder head on wooden blocks.

  1. A150970E01
    Using SST and a hammer, tap in a new guide bush to the specified protrusion height.
    SST
    09201-10000   (09201-01050)
    09950-70010   (09951-07100)

    Protrusion height:
    11.15 to 11.55 mm (0.4390 to 0.4547 in.)

  1. A150972
    Using a sharp 5.5 mm reamer, ream the guide bush to obtain the standard specified clearance between the guide bush and valve stem.

    Standard oil clearance:
    0.030 to 0.065 mm (0.0012 to 0.0026 in.)


3. REPLACE RING PIN

NOTICE:
It is not necessary to remove the ring pin unless it is being replaced.

  1. Remove the 2 ring pins.

  1. A150959E01
    Using a plastic-faced hammer, tap in 2 new ring pins to the specified protrusion height.

    Protrusion height:
    6.5 to 7.5 mm (0.26 to 0.30 in.)


4. REPLACE STUD BOLT

NOTICE:
If the stud bolt is deformed or the threads are damaged, replace it.

  1. Remove the stud bolts.

  1. Using E8 "TORX" socket, install the stud bolts.

    Torque:
    9.5 N*m{ 97 kgf*cm , 84 in.*lbf }


    A150960E01

← INSPECTION (from Nov 2006)REASSEMBLY (from Nov 2006) →