2005-2008 Yaris · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built from Nov 2006


1. INSTALL FUEL INJECTOR ASSEMBLY

  1. A158250E01
    Apply a light coat of gasoline to new O-rings, then install one onto each fuel injector.

  1. Apply a light coat of gasoline to the contact surfaces of the fuel delivery pipe and the O-ring of the fuel injector.

  1. A158251E01
    While turning the fuel injector left and right, install it onto the fuel delivery pipe.

    NOTICE:
    1. Do not twist the O-ring.
    1. After installing the fuel injectors, check that they turn smoothly. If not, replace the O-ring with a new one.


2. INSTALL INJECTOR VIBRATION INSULATOR

  1. A158248
    Install 4 new injector vibration insulators onto the cylinder head.


3. INSTALL NO. 1 DELIVERY PIPE SPACER

  1. A159387
    Install the 2 No. 1 delivery pipe spacers onto the cylinder head.

    NOTICE:
    Install the No. 1 delivery pipe spacers in the correct direction.


4. INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY

  1. A159388
    Install the fuel delivery pipe with the 4 fuel injectors, then provisionally install the 3 bolts.

    NOTICE:
    1. Do not drop the fuel injectors when installing the fuel delivery pipe.
    1. Check that the fuel injectors rotate smoothly after installing the fuel delivery pipe.

  1. Tighten the 3 bolts to the specified torque.

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }


5. CONNECT FUEL TUBE SUB-ASSEMBLY

  1. A158252
    Insert the fuel tube connector into the fuel pipe until a click sound can be heard.

    NOTICE:
    1. Check that there are no scratches or foreign matter around the disconnected parts of the fuel tube connector and pipe before performing this work.
    1. After connecting the fuel tube, check that the fuel tube connector and pipe are securely connected by pulling them.


6. INSTALL FUEL PIPE CLAMP

  1. A158243
    Install the fuel pipe clamp.


7. CONNECT VACUUM HOSE

  1. A158242
    Connect the vacuum hose.


8. CONNECT NO. 1 FUEL VAPOR FEED HOSE

  1. A158241
    Connect the No. 1 fuel vapor feed hose.


9. INSTALL HARNESS BRACKET

  1. A158240
    Install the 2 harness brackets with the 2 bolts.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }


10. INSTALL ENGINE WIRE HARNESS

  1. A158239
    Connect the 4 wire harness clamps shown in the illustration.


11. INSTALL NO. 2 VENTILATION HOSE

  1. A158237
    Install the No. 2 ventilation hose.


12. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


13. INSPECT FOR FUEL LEAK
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and the intelligent tester main switch ON.

    NOTICE:
    Do not start the engine.

  1. Select the following menu items: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump /Speed.

  1. Check that there is no fuel leakage anywhere in the fuel system after doing maintenance.


14. INSTALL NO. 2 CYLINDER HEAD COVER

  1. A158207
    Disengage the 4 fittings shown and install the No. 2 cylinder head cover by applying pressure to it.

    HINT:
    Make sure that the oil and the engine oil level dipstick are correctly installed before installing the No. 2 cylinder head cover.

← INSPECTION (from Nov 2006)COMPONENTS (from Nov 2006) →