DTC P0120 Throttle / Pedal Position Sensor / Switch "A" Circuit Malfunction |
DTC P0121 Throttle / Pedal Position Sensor / Switch "A" Circuit Range / Performance Problem |
DTC P0122 Throttle / Pedal Position Sensor / Switch "A" Circuit Low Input |
DTC P0123 Throttle / Pedal Position Sensor / Switch "A" Circuit High Input |
DTC P0220 Throttle / Pedal Position Sensor / Switch "B" Circuit |
DTC P0222 Throttle / Pedal Position Sensor / Switch "B" Circuit Low Input |
DTC P0223 Throttle / Pedal Position Sensor / Switch "B" Circuit High Input |
DTC P2135 Throttle / Pedal Position Sensor / Switch "A" / "B" Voltage Correlation |

| DTC No. | DTC Detection Conditions | Trouble Areas |
| P0120 | Output voltage of VTA1 quickly fluctuates beyond lower and upper malfunction thresholds for 2 seconds when accelerator pedal depressed (1 trip detection logic) |
|
| P0121 | Difference between VTA1 and VTA2 voltages less than 0.8 V, or more than 1.6 V for 2 seconds (1 trip detection logic) |
|
| P0122 | Output voltage of VTA1 0.2 V or less for 2 seconds when accelerator pedal depressed (1 trip detection logic) |
|
| P0123 | Output voltage of VTA1 4.535 V or more for 2 seconds when accelerator pedal depressed (1 trip detection logic) |
|
| P0220 | Output voltage of VTA2 quickly fluctuates beyond lower and upper malfunction thresholds for 2 seconds when accelerator pedal depressed (1 trip detection logic) |
|
| P0222 | Output voltage of VTA2 1.75 V or less for 2 seconds when accelerator pedal depressed (1 trip detection logic) |
|
| P0223 | Output voltage of VTA2 4.8 V or more, and VTA1 between 0.2 V and 2.02 V, for 2 seconds when accelerator pedal depressed (1 trip detection logic) |
|
| P2135 | Either condition (a) or (b) met (1 trip detection logic): (a) Difference between output voltages of VTA1 and VTA2 0.02 V or less for 0.5 seconds or more (b) Output voltage of VTA1 0.2 V or less, and VTA2 1.75 V or less, for 0.4 seconds or more |
|
| Tester Display | Accelerator Pedal Fully Released | Accelerator Pedal Fully Depressed |
| Throttle Position No. 1 | 0.5 to 1.1 V | 3.2 to 4.8 V |
| Throttle Position No. 2 | 2.1 to 3.1 V | 4.6 to 5.0 V |

| 1.READ VALUE USING INTELLIGENT TESTER (THROTTLE POSITION NO. 1 AND THROTTLE POSITION NO. 2) |
Connect an intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Select the following menu items: Powertrain / Engine and ECT / Data List / Throttle Position No. 1 and Throttle Position No. 2.
Read the values displayed on the tester.
| TP No. 1 (VTA1) When Accelerator Pedal Released | TP No. 2 (VTA2) When Accelerator Pedal Released | TP No. 1 (VTA1) When Accelerator Pedal Depressed | TP No. 2 (VTA2) When Accelerator Pedal Depressed | Trouble Areas | Proceed To |
| 0 to 0.2 V | 0 to 0.2 V | 0 to 0.2 V | 0 to 0.2 V | VC circuit open | A |
| 4.5 to 5.0 V | 4.5 to 5.0 V | 4.5 to 5.0 V | 4.5 to 5.0 V | E2 circuit open | |
| 0 to 0.2 V, or 4.5 to 5.0 V | 2.1 to 3.1 V (Fail-safe) | 0 to 0.2 V, or 4.5 to 5.0 V | 2.1 to 3.1 V (Fail-safe) | VTA1 circuit open or ground short | |
| 0.6 to 1.4 V (Fail-safe) | 0 to 0.2 V, or 4.5 to 5.0 V | 0.6 to 1.4 V (Fail-safe) | 0 to 0.2 V, or 4.5 to 5.0 V | VTA2 circuit open or ground short | |
| 0.5 to 1.1 V | 2.1 to 3.1 V | 3.2 to 4.8 V (Not fail-safe) | 4.6 to 5.0 V (Not fail-safe) | TP sensor circuit normal | B |
|
| ||||
| A | |
| 2.CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM) |
![]() |
Disconnect the C17 throttle body connector.
Disconnect the C20 ECM connector.
Check the resistance.
| Tester Connections | Specified Conditions |
| VC (C17-5) - VCTA (C20-67) | Below 1 Ω |
| VTA (C17-6) - VTA1 (C20-115) | |
| VTA2 (C17-4) - VTA2 (C20-114) | |
| E2 (C17-3) - ETA (C20-91) |
| Tester Connections | Specified Conditions |
| VC (C17-5) or VCTA (C20-67) - Body ground | 10 kΩ or higher |
| VTA (C17-6) or VTA1 (C20-115) - Body ground | |
| VTA2 (C17-4) or VTA2 (C20-114) - Body ground |
Reconnect the throttle body connector.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 3.INSPECT ECM (VC VOLTAGE) |
![]() |
Disconnect the C17 throttle body connector.
Turn the ignition switch to ON.
Measure the voltage between the terminals of the throttle body connector.
| Tester Connections | Specified Conditions |
| VC (C17-5) - E2 (C17-3) | 4.5 to 5.5 V |
Reconnect the throttle body connector.
|
| ||||
| OK | |
| 4.REPLACE THROTTLE BODY ASSEMBLY |
Replace the throttle body assembly (Click here).
| NEXT | |
| 5.CHECK WHETHER DTC OUTPUT RECURS (THROTTLE POSITION SENSOR DTCS) |
Connect an intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Clear DTCs (Click here).
Start the engine.
Allow the engine to idle for 15 seconds or more.
Select the following menu items: Powertrain / Engine and ECT / DTC.
Read DTCs.
| Display (DTC Output) | Proceed To |
| P0120, P0121, P0122, P0123, P0220, P0222, P0223, and/or P2135 | A |
| No output | B |
|
| ||||
| A | ||
| ||