DTC P2120 Throttle / Pedal Position Sensor / Switch "D" Circuit |
DTC P2122 Throttle / Pedal Position Sensor / Switch "D" Circuit Low Input |
DTC P2123 Throttle / Pedal Position Sensor / Switch "D" Circuit High Input |
DTC P2125 Throttle / Pedal Position Sensor / Switch "E" Circuit |
DTC P2127 Throttle / Pedal Position Sensor / Switch "E" Circuit Low Input |
DTC P2128 Throttle / Pedal Position Sensor / Switch "E" Circuit High Input |
DTC P2138 Throttle / Pedal Position Sensor / Switch "D" / "E" Voltage Correlation |

| DTC No. | DTC Detection Conditions | Trouble Areas |
| P2120 | VPA fluctuates rapidly beyond upper and lower malfunction thresholds for 0.5 seconds or more (1 trip detection logic) |
|
| P2122 | VPA 0.4 V or less for 0.5 seconds or more when accelerator pedal fully released (1 trip detection logic) |
|
| P2123 | VPA 4.8 V or more for 2.0 seconds or more (1 trip detection logic) |
|
| P2125 | VPA2 fluctuates rapidly beyond upper and lower malfunction thresholds for 0.5 seconds or more (1 trip detection logic) |
|
| P2127 | VPA2 1.2 V or less for 0.5 seconds or more when accelerator pedal fully released (1 trip detection logic) |
|
| P2128 | Conditions (a) and (b) continue for 2.0 seconds or more (1 trip detection logic): (a) VPA2 4.8 V or more (b) VPA between 0.4 V and 3.45 V |
|
| P2138 | Condition (a) or (b) continues for 2.0 seconds or more (1 trip detection logic): (a) Difference between VPA and VPA2 0.02 V or less (b) VPA 0.4 V or less and VPA2 1.2 V or less |
|
| Trouble Areas | Accelerator Position No. 1 When Accelerator Pedal Released | Accelerator Position No. 2 When Accelerator Pedal Released | Accelerator Position No. 1 When Accelerator Pedal Depressed | Accelerator Position No. 2 When Accelerator Pedal Depressed |
| VCP circuit open | 0 to 0.2 V | 0 to 0.2 V | 0 to 0.2 V | 0 to 0.2 V |
| Open or ground short in VPA circuit | 0 to 0.2 V | 1.2 to 2.0 V | 0 to 0.2 V | 3.4 to 5.0 V |
| Open or ground short in VPA2 circuit | 0.5 to 1.1 V | 0 to 0.2 V | 2.6 to 4.5 V | 0 to 0.2 V |
| EPA circuit open | 4.5 to 5.0 V | 4.5 to 5.0 V | 4.5 to 5.0 V | 4.5 to 5.0 V |
| Normal condition | 0.5 to 1.1 V | 1.2 to 2.0 V | 2.6 to 4.5 V | 3.4 to 5.0 V |

| 1.READ VALUE USING INTELLIGENT TESTER (ACCELERATOR POSITION NO. 1 AND ACCELERATOR POSITION NO. 2) |
![]() |
Connect an intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Select the following menu items: Powertrain / Engine and ECT / Data List / Accelerator Position No. 1 and Accelerator Position No. 2.
Read the value displayed on the tester.
| Accelerator Pedal Operations | Accelerator Position No. 1 | Accelerator Position No. 2 |
| Released → Depressed → Released | 0.5 to 4.5 V | 1.2 to 5.0 V |
| Difference between Accelerator Position No. 1 and Accelerator Position No. 2 is greater than 0.02 V | Difference between Accelerator Position No. 1 and Accelerator Position No. 2 is greater than 0.02 V |
|
| ||||
| NG | |
| 2.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM) |
![]() |
Disconnect the A20 Accelerator Pedal Position (APP) sensor connector.
Disconnect the A21 ECM connector.
Check the resistance.
| Tester Connections | Specified Conditions |
| VPA (A20-6) - VPA (A21-55) | Below 1 Ω |
| EPA (A20-5) - EPA (A21-59) | |
| VCPA (A20-4) - VCPA (A21-57) | |
| VPA2 (A20-3) - VPA2 (A21-56) | |
| EPA2 (A20-2) - EPA2 (A21-60) | |
| VCP2 (A20-1) - VCP2 (A21-58) |
| Tester Connections | Specified Conditions |
| VPA (A20-6) or VPA (A21-55) - Body ground | 10 kΩ or higher |
| EPA (A20-5) or EPA (A21-59) - Body ground | |
| VCPA (A20-4) or VCPA (A21-57) - Body ground | |
| VPA2 (A20-3) or VPA2 (A21-56) - Body ground | |
| EPA2 (A20-2) or EPA2 (A21-60) - Body ground | |
| VCP2 (A20-1) or VCP2 (A21-58) - Body ground |
Reconnect the APP sensor connector.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 3.INSPECT ECM (VCPA AND VCP2 VOLTAGE) |
![]() |
Disconnect the A20 APP sensor connector.
Turn the ignition switch to ON.
Measure the voltage between the terminals of the A20 APP sensor connector.
| Tester Connections | Specified Conditions |
| VCPA (A20-4) - EPA (A20-5) | 4.5 to 5.5 V |
| VCP2 (A20-1) - EPA2 (A20-2) |
Reconnect the APP sensor connector.
|
| ||||
| OK | |
| 4.REPLACE ACCELERATOR PEDAL ASSEMBLY |
| NEXT | |
| 5.CHECK WHETHER DTC OUTPUT RECURS (ACCELERATOR PEDAL POSITION SENSOR DTCS) |
Connect an intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Clear DTCs (Click here).
Start the engine.
Allow the engine to idle for 15 seconds.
Select the following menu items: Powertrain / Engine and ECT / DTC.
Read DTCs.
| Display (DTC Output) | Proceed To |
| P2120, P2122, P2123, P2125, P2127, P2128, and/or P2138 | A |
| No output | B |
|
| ||||
| A | ||
| ||