Home › BODY › WINDSHIELD / WINDOWGLASS › WINDSHIELD GLASS (for Hatchback)

WINDSHIELD GLASS (for Hatchback) > INSTALLATION

for Preparation Click here



1. CLEAN WINDSHIELD GLASS


B073128E01
  1. Using a scraper, remove the damaged stoppers, dam and adhesive from the windshield glass.

  1. Clean the outer circumference of the windshield glass with a non-residue solvent.

    NOTICE:
    1. Do not touch the windshield glass surface after cleaning it.
    2. Even if using a new windshield glass, clean the windshield glass with a non-residue solvent.



2. CLEAN VEHICLE BODY


B073084E02
  1. Clean and shape the contact surface of the vehicle body.

    1. Using a knife, cut away any rough adhesive on the contact surface of the vehicle body to ensure the appropriate surface shape.

      NOTICE:
      Do not damage the vehicle body.

      HINT:
      Leave as much adhesive on the vehicle body as possible.

    2. Clean the contact surface of the vehicle body with a shop rag or piece of cloth saturated with cleaner.

      HINT:
      Clean the vehicle body even if all the adhesive has been removed.



3. INSTALL WINDSHIELD GLASS STOPPER NO. 1


B107866
  1. Install 2 new stoppers onto the vehicle body, as shown in the illustration.



4. INSTALL WINDSHIELD GLASS STOPPER NO. 2


B107883E01
  1. Apply Primer G to the installation parts of the stoppers.

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Throw away any leftover Primer G.
    3. Do not apply too much Primer G.

  1. Install 2 new stoppers onto the windshield glass, as shown in the illustration.

    Specification:
    Area
    Measurement
    a
    40 mm (1.57 in.)
    b
    14.5 mm (0.571 in.)



5. INSTALL WINDSHIELD OUTSIDE MOULDING


B127221E01
  1. Using a brush or sponge, coat the edge of the glass and the contact surface with Primer G.

    NOTICE:
    1. Allow the primer coating to dry for 3 minutes or more.
    2. Do not coat the adhesive with Primer G.
    3. Throw away any leftover Primer G.

  1. Install the moulding onto the windshield glass, as shown in the illustration.

    Specification:
    Area
    Measurement
    a
    0.1mm (0.004 in.)



6. INSTALL WINDOW GLASS ADHESIVE DAM
  1. Apply Primer G to the installation part of a new dam, as shown in the illustration.

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Throw away any leftover Primer G.
    3. Do not apply too much Primer G.



    B107885E01
  1. Install the new dam with double-sided tape as shown in the illustration.

    Specification:
    Area
    Measurement
    a
    32 mm (1.26 in.)



7. INSTALL WINDSHIELD GLASS


    B116960E01
  1. Position the windshield glass.

    1. Using suction cups, place the windshield glass in the correct position.

    2. Check that the entire contact surface of the windshield glass rim is perfectly even.

    3. Place matchmarks on the windshield glass and vehicle body.

      NOTICE:
      Check that the stoppers are correctly attached to the vehicle body.

      HINT:
      When reusing a windshield glass, check and correct the matchmark positions.

    4. Using suction cups, remove the windshield glass.



    B106027E01
  1. Using a brush, apply Primer M to the exposed part of the vehicle body.

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Do not apply Primer M to the adhesive.
    3. Throw away any leftover Primer M.
    4. Do not apply too much Primer M.



  1. Using a brush or sponge, apply Primer G to the edge of the windshield glass and the contact surface.


    B107886E01

    Specification:
    Area
    Measurement
    a
    8.0 mm (0.315 in.)
    b
    19 mm (0.748 in.)

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Throw away any leftover Primer G.
    3. Do not apply too much Primer G.

    HINT:
    If Primer G is applied to any areas other than those specified, wipe off the primer with a clean shop rag or piece of cloth before it dries.



  1. Apply adhesive.

    Adhesive:
    Toyota Genuine Windshield Glass Adhesive or equivalent




      B106205E01
    1. Cut the tip off the cartridge nozzle, as shown in the illustration.

      HINT:
      After cutting off the tip, use all adhesive within the times indicated in the table below.

      Usage time frame:
      Temperature
      Usage Time Frame
      35°C (95°F)
      15 minutes
      20°C (68°F)
      1 hour 40 minutes
      5°C (41°F)
      8 hours

    2. Load the sealer gun with the cartridge.



    3. Apply adhesive to the windshield glass, as shown in the illustration.


      B107887E01

      Specification:
      Area
      Measurement
      a
      8 mm (0.315 in.)
      b
      12 mm (0.472 in.)
      c
      10 mm (0.394 in.)
      d
      17.5 mm (0.689 in.)



    B116960E02
  1. Install the windshield glass onto the vehicle body.

    1. Using suction cups, position the windshield glass so that the matchmarks are aligned. Gently press it in along the rim.

      NOTICE:
      1. Allow the primer to dry for 3 minutes or more.
      2. Check that the stoppers are attached to the vehicle body correctly.
      3. Check that there is a small gap between the vehicle body and the windshield glass.

    2. Gently press the front surface of the windshield glass to ensure that the windshield glass is securely fitted to the vehicle body.



    3. B073131
    4. Using a scraper, remove any excessive or protruding adhesive.

      HINT:
      Apply adhesive to the windshield glass rim.

      NOTICE:
      Do not to drive the vehicle within the time indicated in the table below.

      Minimum time:
      Temperature
      Minimum time prior to driving vehicle
      35°C (95°F)
      1 hour 30 minutes
      20°C (68°F)
      5 hours
      5°C (41°F)
      24 hours



8. CHECK FOR LEAKAGE AND REPAIR
  1. Conduct a leak test by applying water to the adhesive portions after the adhesive has completely hardened.

  1. Seal any leaks with auto glass sealer.



9. INSTALL INNER REAR VIEW MIRROR ASSEMBLY


B087505
  1. Slide the inner rear view mirror to install it.



    B118044
  1. Engage the 2 claws and install the cover.



10. INSTALL ROOF HEADLINING


11. INSTALL FRONT PILLAR GARNISH RH


    B114342E01
  1. w/ Curtain Shield Airbag:

    1. Remove the piece of cloth or nylon.



    B127672
  1. w/ Front No. 2 Speaker:

    1. Insert the hook into the body hole.

    2. Engage the clip and install the front speaker.



    3. B127674
    4. Connect the speaker connector.



    B114312
  1. Install the 3 antenna cord clamps.

  1. Connect the connector.



  1. w/ Curtain Shield Airbag:



      B117697E01
    1. Install a new special clip and the clip onto a new front pillar garnish.

    2. Engage the 2 clips and the 2 claws and install the front pillar garnish.



  1. w/o Curtain Shield Airbag:



      B117694
    1. Engage the 2 clips and the 2 claws and install the front pillar garnish.



12. INSTALL FRONT PILLAR GARNISH LH


    B114344E01
  1. w/ Curtain Shield Airbag:

    1. Remove the piece of cloth or nylon.



    B127671
  1. w/ Front No. 2 Speaker:

    1. Insert the hook into the body hole.

    2. Engage the clip and install the front speaker.



    3. B127673
    4. Connect the speaker connector.



    B114316
  1. Install the 4 wire harness clamps.



  1. w/ Curtain Shield Airbag:



      B117698E01
    1. Install a new special clip and the clip onto a new front pillar garnish.

    2. Engage the 2 clips and the 2 claws and install the front pillar garnish.



  1. w/o Curtain Shield Airbag:



      B114318
    1. Engage the 2 clips and the 2 claws and install the front pillar garnish.



13. INSTALL MAP LIGHT ASSEMBLY


E114447
  1. Connect the connector.

  1. Engage the 4 claws and install the map light.



14. INSTALL VISOR HOLDER RH


    B114350E01
  1. Engage the 2 claws by turning the visor holder clockwise between 60 to 120° and install the visor holder.



15. INSTALL VISOR HOLDER LH

HINT:
Use the same procedure as for the RH side.



16. INSTALL VISOR ASSEMBLY RH


    B114304
  1. Engage the 2 springs and install the visor.

  1. Install the visor shaft into the visor holder.



    B114351
  1. Engage the 4 claws and install the visor bracket cover.



17. INSTALL VISOR ASSEMBLY LH

HINT:
Use the same procedure as for the RH side.



18. INSTALL ASSIST GRIP SUB-ASSEMBLY


B114302

HINT:
The number of the assist grips varies with the specifications.

  1. Engage the 2 springs and install the assist grip.



19. INSTALL ASSIST GRIP COVER


B114352

HINT:
The number of the assist grip covers varies with the specifications.

  1. Engage the 2 claws and install the assist grip cover.



20. INSTALL ROOF HEADLINING SERVICE HOLE COVER (w/o Curtain Shield Airbag)


B114353

HINT:
The number of the roof headlining service hole covers varies with the specifications.

  1. Install the roof headlining service hole cover.



21. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH


    B130371E01
  1. Align the location mark with the paint mark first, and install the front door opening trim weatherstrip, as shown in the illustration.
    Paint mark: 
    Area
    Color
    RH side
    Gold
    LH side
    Silver



22. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

HINT:
Use the same procedure as for the RH side.



23. INSTALL COWL SIDE TRIM BOARD RH


    B114285
  1. Engage the claw and stud bolt and install the cowl side trim board.



24. INSTALL COWL SIDE TRIM BOARD LH

HINT:
Use the same procedure as for the RH side.



25. INSTALL FRONT DOOR SCUFF PLATE RH


    B114284
  1. Engage the 8 claws and install the front door scuff plate.



26. INSTALL FRONT DOOR SCUFF PLATE LH

HINT:
Use the same procedure as for the RH side.



27. INSTALL COWL TOP VENTILATOR LOUVER LH (for LHD)


E113853
  1. Engage the 4 claws and install the cowl top ventilator louver LH.

  1. Install the 2 clips.



28. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for LHD)


E113854
  1. Connect the washer hose.



    E113852
  1. Engage the 11 claws and install the cowl top ventilator louver sub-assembly.

  1. Install the clip.

  1. Connect the washer hose.



    E117641
  1. Engage the 2 hooks and install cowl top ventilator louver center No. 1.



29. INSTALL COWL TOP VENTILATOR LOUVER LH (for RHD)


E113856
  1. Engage the 4 claws and install the cowl top ventilator louver LH.

  1. Install the clip.



30. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for RHD)


E113855
  1. Engage the 10 claws and install the cowl top ventilator louver sub-assembly.

  1. Install the clip.

  1. Connect the washer hose.



31. INSTALL HOOD TO COWL TOP SEAL


E113851
  1. Engage the 7 clips and install the hood to cowl top seal.



32. INSTALL FRONT WIPER ARM BLADE ASSEMBLY LH


E058837E10
  1. Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.



    E113862E01
  1. Align the blade tip with the mark on the windshield glass, as shown in the illustration.

  1. Tighten the nut of the front wiper arm.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }



33. INSTALL FRONT WIPER ARM BLADE ASSEMBLY RH


E058837E10
  1. Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.



    E113863E01
  1. Align the blade tip with the mark on the windshield glass, as shown in the illustration.

  1. Tighten the nut of the front wiper arm.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }



34. INSTALL FRONT WIPER ARM HEAD CAP


E113849
  1. Engage the claw and install the 2 front wiper arm head caps.



35. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



36. INSPECT SRS WARNING LIGHT
(Click here)