WINDSHIELD GLASS (for Sedan) > INSTALLATION |
| 1. CLEAN WINDSHIELD GLASS |
![]() |
Using a scraper, remove the stoppers, dam and adhesive from the windshield glass.
Clean the outer circumference of the windshield glass with a non-residue solvent.
| 2. CLEAN VEHICLE BODY |
![]() |
Clean and shape the contact surface of the vehicle body.
Using a knife, cut away any rough adhesive on the contact surface of the vehicle body to ensure the appropriate surface shape.
Clean the contact surface of the vehicle body with a shop rag or piece of cloth saturated with cleaner.
| 3. INSTALL WINDSHIELD GLASS STOPPER NO. 1 |
![]() |
Install 2 new stoppers onto the vehicle body, as shown in the illustration.
| 4. INSTALL WINDSHIELD GLASS STOPPER NO. 2 |
![]() |
Apply Primer G to the installation parts of the stoppers.
Install 2 new stoppers onto the windshield glass, as shown in the illustration.
| Area | Measurement |
| a | 40 mm (1.57 in.) |
| b | 14.5 mm (0.571 in.) |
| 5. INSTALL WINDOW GLASS ADHESIVE DAM |
Apply Primer G to the installation part of a new dam, as shown in the illustration.
Install the new dam with double-sided tape as shown in the illustration.

| Area | Measurement |
| a | 7.0 mm (0.276 in.) |
| b | 29.4 mm (1.157 in.) |
| 6. INSTALL WINDSHIELD GLASS |
![]() |
Position the windshield glass.
Using suction cups, place the windshield glass in the correct position.
Check that the entire contact surface of the windshield glass rim is perfectly even.
Place matchmarks on the windshield glass and vehicle body.
Using suction cups, remove the windshield glass.
![]() |
Using a brush, apply Primer M to the exposed part of the vehicle body.
Using a brush or sponge, apply Primer G to the edge of the windshield glass and the contact surface.

| Area | Measurement |
| a | 7.0 mm (0.276 in.) |
| b | 7.0 mm (0.276 in.) |
| c | 16 mm (0.630 in.) |
Apply adhesive.
![]() |
Cut the tip off the cartridge nozzle, as shown in the illustration.
| Temperature | Usage Time Frame |
| 35°C (95°F) | 15 minutes |
| 20°C (68°F) | 1 hour 40 minutes |
| 5°C (41°F) | 8 hours |
Load the sealer gun with the cartridge.
Apply adhesive to the windshield glass, as shown in the illustration.

| Area | Measurement |
| a | 8 mm (0.315 in.) |
| b | 12 mm (0.472 in.) |
| c | 3 mm (0.118 in.) |
| d | 3 mm (0.118 in.) |
| e | 17.4 mm (0.685 in.) |
![]() |
Install the windshield glass onto the vehicle body.
Using suction cups, position the windshield glass so that the matchmarks are aligned. Gently press it in along the rim.
Gently press the front surface of the windshield glass to ensure that the windshield glass is securely fitted to the vehicle body.
![]() |
Using a scraper, remove any excessive or protruding adhesive.
| Temperature | Minimum time prior to driving vehicle |
| 35°C (95°F) | 1 hour 30 minutes |
| 20°C (68°F) | 5 hours |
| 5°C (41°F) | 24 hours |
| 7. INSTALL WINDSHIELD OUTSIDE MOULDING |
![]() |
Using a brush or sponge, coat the edge of the glass and the contact surface with Primer G.
Install a new moulding onto the windshield glass, as shown in the illustration.
| Area | Measurement |
| a | 2 mm (0.0787 in.) |
| 8. CHECK FOR LEAKAGE AND REPAIR |
Conduct a leak test by applying water to the adhesive portions after the adhesive has completely hardened.
Seal any leaks with auto glass sealer.
| 9. INSTALL ROOF HEADLINING ASSEMBLY |
| 10. INSTALL INNER REAR VIEW MIRROR |
![]() |
Slide the inner rear view mirror to install it.
![]() |
Engage the 2 claws and install the cover.
| 11. INSTALL MAP LIGHT ASSEMBLY |
![]() |
Connect the connector.
Engage the 4 claws and install the map light.
| 12. INSTALL ROOM LIGHT ASSEMBLY |
Install room light bulb No. 1.
![]() |
Engage the 4 claws and install the room light switch base.
Install the roof wire into the claw of the room light.
![]() |
Engage the 4 claws and install the room light.
![]() |
Engage the 4 claws and install the 2 covers.
![]() |
Engage the 4 claws and install the room light lens.
| 13. INSTALL VISOR HOLDER RH |
![]() |
Engage the 2 claws by turning the visor holder clockwise between 60 to 120° and install the visor holder.
| 14. INSTALL VISOR HOLDER LH |
| 15. INSTALL VISOR ASSEMBLY RH |
![]() |
Engage the 2 springs and install the visor.
Install the visor shaft into the visor holder.
![]() |
Engage the 4 claws and install the visor bracket cover.
| 16. INSTALL VISOR ASSEMBLY LH |
| 17. INSTALL ASSIST GRIP SUB-ASSEMBLY |
![]() |
![]() |
Engage the 2 springs and install the assist grip.
| 18. INSTALL ASSIST GRIP COVER |
![]() |
![]() |
Engage the 2 claws and install the assist grip cover.
| 19. INSTALL ROOF HEADLINING SERVICE HOLE COVER (w/o Curtain Shield Airbag) |
![]() |
![]() |
Install the roof headlining service hole cover.
| 20. INSTALL FRONT PILLAR GARNISH RH |
![]() |
w/ Curtain Shield Airbag:
Remove the piece of cloth or nylon.
![]() |
Install the 3 clamps.
Connect the antenna connector.
![]() |
w/ Curtain Shield Airbag:
Install a new special clip and the clip onto the front pillar garnish.
Engage the 2 clips and the 2 claws and install the front pillar garnish.
![]() |
w/o Curtain Shield Airbag:
Engage the 2 clips and the 2 claws and install the front pillar garnish.
| 21. INSTALL FRONT PILLAR GARNISH LH |
![]() |
w/ Curtain Shield Airbag:
Remove the piece of cloth or nylon.
![]() |
Install the 4 clamps.
![]() |
w/ Curtain Shield Airbag:
Install a new special clip and the clip onto the front pillar garnish.
Engage the 2 clips and the 2 claws and install the front pillar garnish.
![]() |
w/o Curtain Shield Airbag:
Engage the 2 clips and the 2 claws and install the front pillar garnish.
| 22. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH |
![]() |
Align the location mark with the paint mark first, and install the front door opening trim weatherstrip, as shown in the illustration.
| Area | Color |
| RH side | Blue |
| LH side | Pink |
| 23. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH |
| 24. INSTALL COWL SIDE TRIM BOARD RH |
![]() |
Engage the stud bolt and the claw and install the cowl side trim board.
| 25. INSTALL COWL SIDE TRIM BOARD LH |
| 26. INSTALL FRONT DOOR SCUFF PLATE RH |
![]() |
Engage the 11 claws and install the front door scuff plate.
| 27. INSTALL FRONT DOOR SCUFF PLATE LH |
| 28. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for RHD) |
![]() |
Connect the washer hoses.
Engage the 5 hooks.
![]() |
Engage the 10 hooks and the 6 claws.
Install the cowl top ventilator louver sub-assembly with the 2 clips.
| 29. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for LHD) |
![]() |
Connect the washer hoses.
Engage the 5 hooks.
![]() |
Engage the 8 hooks and the 4 claws.
Install the cowl top ventilator louver sub-assembly with the 3 clips.
| 30. INSTALL COWL SIDE VENTILATOR SUB-ASSEMBLY LH |
![]() |
Engage the 3 claws and install the cowl side ventilator sub-assembly LH.
| 31. INSTALL COWL SIDE VENTILATOR SUB-ASSEMBLY RH |
| 32. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH |
![]() |
Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).
Clean the wiper pivot serrations with a wire brush.
Operate the wiper, then stop the windshield wiper motor in the automatic stop position.
![]() |
Align the blade tip with the mark on the windshield glass, as shown in the illustration.
Tighten the nut of the front wiper arm.
| 33. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH |
![]() |
Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).
Clean the wiper pivot serrations with a wire brush.
Operate the wiper, then stop the windshield wiper motor in the automatic stop position.
![]() |
Align the blade tip with the mark on the windshield glass, as shown in the illustration.
Tighten the nut of the front wiper arm.
| 34. INSTALL FRONT WIPER ARM HEAD CAP |
![]() |
Engage the claw and install the 2 front wiper arm head caps.
| 35. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 36. INSPECT SRS WARNING LIGHT |