Home › BODY › WINDSHIELD / WINDOWGLASS › BACK WINDOW GLASS (for Sedan)

BACK WINDOW GLASS (for Sedan) > INSTALLATION

for Preparation Click here



1. CLEAN BACK WINDOW GLASS


B073128E01
  1. Using a scraper, remove the stoppers, dam and adhesive from the back window glass.

  1. Clean the outer circumference of the back window glass with a non-residue solvent.

    NOTICE:
    1. Do not touch the back window glass surface after cleaning it.
    2. Even if using a new back window glass, clean the back window glass with a non-residue solvent.



2. CLEAN VEHICLE BODY


B073084E02
  1. Clean and shape the contact surface of the vehicle body.

    1. Using a knife, cut away any rough adhesive on the contact surface of the vehicle body to ensure the appropriate surface shape.

      NOTICE:
      Do not damage the vehicle body.

      HINT:
      Leave as much adhesive on the vehicle body as possible.

    2. Clean the contact surface of the vehicle body with a shop rag or piece of cloth saturated with cleaner.

      HINT:
      Clean the vehicle body even if all the adhesive has been removed.



3. INSTALL BACK WINDOW GLASS STOPPER NO. 1


B136261
  1. Install 2 new stoppers onto the vehicle body, as shown in the illustration.



4. INSTALL BACK WINDOW GLASS STOPPER NO. 2


B136262E01
  1. Apply Primer G to the installation parts of the stoppers.

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Throw away any leftover Primer G.
    3. Do not apply too much Primer G.

  1. Install 2 new stoppers onto the windshield glass, as shown in the illustration.

    Specification:
    Area
    Measurement
    a
    40 mm (1.57 in.)
    b
    14.9 mm (0.587 in.)



5. INSTALL BACK WINDOW GLASS ADHESIVE DAM
  1. Apply Primer G to the installation part of a new dam, as shown in the illustration.

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Throw away any leftover Primer G.
    3. Do not apply too much Primer G.



    B136264E01
  1. Install the new dam with double-sided tape as shown in the illustration.

    Specification:
    Area
    Measurement
    a
    4.0 mm (0.157 in.)



6. INSTALL BACK WINDOW GLASS


    B136260E01
  1. Position the back window glass.

    1. Using suction cups, place the back window glass in the correct position.

    2. Check that the entire contact surface of the back window glass rim is perfectly even.

    3. Place matchmarks on the back window glass and vehicle body.

      NOTICE:
      Check that the stoppers are correctly attached to the vehicle body.

      HINT:
      When reusing the back window glass, check and correct the matchmark positions.

    4. Using suction cups, remove the back window glass.



    B106027E01
  1. Using a brush, apply Primer M to the exposed part of the vehicle body.

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Do not apply Primer M to the adhesive.
    3. Throw away any leftover Primer M.
    4. Do not apply too much Primer M.



  1. Using a brush or sponge, apply Primer G to the edge of the back window glass and the contact surface.


    B136265E01

    Specification:
    Area
    Measurement
    a
    11 mm (0.433 in.)
    b
    11 mm (0.433 in.)
    c
    11 mm (0.433 in.)

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Throw away any leftover Primer G.
    3. Do not apply too much Primer G.

    HINT:
    If Primer G is applied to any areas other than those specified, wipe off the primer with a clean shop rag or piece of cloth before it dries.



  1. Apply adhesive.

    Adhesive:
    Toyota Genuine Windshield Glass Adhesive or the equivalent.




      B106205E01
    1. Cut the tip off the cartridge nozzle, as shown in the illustration.

      HINT:
      After cutting off the tip, use all adhesive within the times indicated in the table below.

      Usage time frame:
      Temperature
      Usage Time Frame
      35°C (95°F)
      15 minutes
      20°C (68°F)
      1 hour 40 minutes
      5°C (41°F)
      8 hours

    2. Load the sealer gun with the cartridge.



    3. Apply adhesive to the back window glass, as shown in the illustration.


      B136266E01

      Specification:
      Area
      Measurement
      a
      8 mm (0.315 in.)
      b
      12 mm (0.472 in.)
      c
      9.3 mm (0.366 in.)
      d
      9.4 mm (0.370 in.)
      e
      13 mm (0.512 in.)



    B136260E01
  1. Install the back window glass onto the vehicle body.

    1. Using suction cups, position the back window glass so that the matchmarks are aligned. Gently press it in along the rim.

      NOTICE:
      1. Allow the primer to dry for 3 minutes or more.
      2. Check that the stoppers are attached to the vehicle body correctly.
      3. Check that there is a small gap between the vehicle body and the back window glass.

    2. Gently press the front surface of the back window glass to ensure that the back window glass is securely fitted to the vehicle body.

      NOTICE:
      Open and close the door gently to prevent the window glass from becoming loose due to the air pressure when the door is closed.



    3. B073131
    4. Using a scraper, remove any excessive or protruding adhesive.

      HINT:
      Apply adhesive to the back window glass rim.

      NOTICE:
      Do not to drive the vehicle within the time indicated in the table below.

      Minimum time:
      Temperature
      Minimum time prior to driving vehicle
      35°C (95°F)
      1 hour 30 minutes
      20°C (68°F)
      5 hours
      5°C (41°F)
      24 hours



7. INSTALL BACK WINDOW OUTSIDE MOULDING

NOTICE:
After the installation of the window glass, install the moulding before the adhesive hardens.



    B136263E01
  1. Using a brush or sponge, coat the edge of the glass and the contact surface with Primer G.

    NOTICE:
    1. Allow the primer coating to dry for 3 minutes or more.
    2. Do not coat the adhesive with Primer G.
    3. Throw away any leftover Primer G.

  1. Install a new moulding onto the back window glass, as shown in the illustration.

    Specification:
    Area
    Measurement
    a
    1.9 mm (0.075 in.)
    b
    1.0 mm (0.039 in.)

    NOTICE:
    Make sure that the moulding is securely installed.



8. CHECK FOR LEAKAGE AND REPAIR
  1. Conduct a leak test by applying water to the adhesive portions after the adhesive has completely hardened.

  1. Seal any leaks with auto glass sealer.



9. INSTALL ROOF HEADLINING ASSEMBLY


10. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY


    B134912
  1. for 3 Point Type Rear Center Seat Belt:

    1. Engage the 5 claws and install the package tray trim.

    2. Install the 4 clips.



    B134913
  1. for 2 Point Type Rear Center Seat Belt:

    1. Engage the 5 claws and install the package tray trim.

    2. Install the 3 clips.



11. INSTALL HIGH MOUNTED STOP LIGHT ASSEMBLY (w/o Rear Spoiler)


    E127792
  1. Connect the connector.

  1. Engage the 4 claws and install the high mounted stop light assembly.



12. INSTALL ASSIST GRIP SUB-ASSEMBLY


B134786

HINT:
The number of the assist grips varies with the specifications.



    B114302
  1. Engage the 2 springs and install the assist grip.



13. INSTALL ASSIST GRIP COVER


B134785

HINT:
The number of the assist grip covers varies with the specifications.



    B114352
  1. Engage the 2 claws and install the assist grip cover.



14. INSTALL ROOF SIDE INNER GARNISH RH


    B134775E01
  1. w/ Curtain Shield Airbag:

    1. Install a new special clip and the clip onto the roof side inner garnish.

    2. Engage the 4 clips and the claw and install the roof side inner garnish.



    B134774
  1. w/o Curtain Shield Airbag:

    1. Engage the 4 clips and the claw and install the roof side inner garnish.



15. INSTALL ROOF SIDE INNER GARNISH LH

HINT:
Use the same procedure as for the RH side.



16. INSTALL REAR SEAT SIDE COVER RH


    B134776
  1. Engage the 2 clips and the 4 claws and install the rear seat side cover.



17. INSTALL REAR SEAT SIDE COVER LH

HINT:
Use the same procedure as for the RH side.



18. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH


    B134773E01
  1. Align the location mark with the paint mark first, and install the rear door opening trim weatherstrip, as shown in the illustration.

    Paint mark:
    Area
    Color
    RH side
    Green
    LH side
    Red



19. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

HINT:
Use the same procedure as for the RH side.



20. INSTALL REAR DOOR SCUFF PLATE RH


    B134771
  1. Engage the 7 claws and install the rear door scuff plate.



21. INSTALL REAR DOOR SCUFF PLATE LH

HINT:
Use the same procedure as for the RH side.



22. INSTALL LUGGAGE COMPARTMENT TRIM INNER PAD (for 60/40 Split Seat Type)


B136275
  1. Install the luggage compartment trim inner pad.



23. INSTALL SPARE WHEEL COVER ASSEMBLY (for 60/40 Split Seat Type)


B136270
  1. Install the spare wheel cover.



24. INSTALL LUGGAGE COMPARTMENT FLOOR MAT (for 60/40 Split Seat Type)


B136269
  1. Install the luggage compartment floor mat.



25. INSTALL REAR SEATBACK ASSEMBLY LH (for 60/40 Split Seat Type)


    B134926E01
  1. Insert the 2 hooks into the rear seatback frame hole and install the rear seatback tightening the 2 bolts in the sequence shown in the illustration.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }



    B134925
  1. Install the rear seatback cover with the 2 clips.

  1. Pull up the rear seatback.



    B134924
  1. Install the rear seat outer belt into the rear seat shoulder belt guide.



26. INSTALL REAR SEATBACK ASSEMBLY RH (for 60/40 Split Seat Type)


    B134945E01
  1. Insert the 2 hooks into the rear seatback frame hole and install the rear seatback tightening the 2 bolts in the sequence shown in the illustration.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }



    B134944
  1. Install the rear seatback cover with the 2 clips.

  1. Pull up the rear seatback.



    B134943
  1. Install the rear seat outer belt into the rear seat shoulder belt guide.

  1. for 3 Point Type Rear Seat Belt:

    1. Install the rear center seat outer belt into the rear center seat shoulder belt guide.



27. INSTALL REAR SEATBACK ASSEMBLY (for Fixed Seat Type)


    B134981
  1. Engage the 3 hooks and install the rear seatback.

  1. Tighten the 3 bolts.

    Torque:
    7.9 N*m{ 80 kgf*cm , 70 in.*lbf }



    B138450E02
  1. Install the rear seat outer belt into the rear seat shoulder belt guide.

    HINT:
    Use the same procedure for both sides.

  1. for 3 Point Type Rear Center Seat belt:

    1. Install the rear center seat outer belt into the rear center seat shoulder belt guide.



28. INSTALL REAR SEAT CUSHION COVER PAD SUB-ASSEMBLY
  1. for 60/40 Split Seat Type:

    1. Install the rear seat cushion cover pad sub-assembly .

  1. for Fixed Seat Type:

    1. Install the rear seat cushion cover pad sub-assembly .



29. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



30. INSPECT SRS WARNING LIGHT
(Click here)