DTC P0617 Starter Relay Circuit High |

| DTC No. | DTC Detection Conditions | Trouble Areas |
| P0617 | When conditions (a), (b) and (c) met for 20 seconds (1 trip detection logic):
|
|

| 1.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL) |
Connect an intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Select the following menu items: Powertrain / Engine and ECT / Data List / Starter Signal.
Read the value displayed on the tester when the ignition switch is turned to ON and the engine starts.
| Conditions | Starter Signal |
| Ignition switch to ON | OFF |
| Engine start | ON |
|
| ||||
| NG | |
| 2.INSPECT PARK/NEUTRAL POSITION SWITCH OR CLUTCH START SWITCH |
![]() |
Inspect the Park/Neutral Position (PNP) switch (for A/T models).
Disconnect the C27 PNP switch connector.
Check the resistance when the transmission gear selector lever is moved to each position.
| Gear Selector Lever Positions | Tester Connections | Specified Conditions |
| P | 2 - 6, 4 - 5 | Below 1 Ω |
| R | 1 - 2 | |
| N | 2 - 9, 4 - 5 | |
| D | 2 - 7 | |
| 2 | 2 - 3 | |
| L | 2 - 8 |
Reconnect the PNP switch connector.
![]() |
Inspect the clutch start switch (for M/T models).
Disconnect the A16 clutch start switch connector.
Check the resistance when the clutch start switch is ON and OFF.
| Switch Positions | Tester Connections | Specified Conditions |
| ON (pushed) | 1 - 2 | Below 1 Ω |
| OFF (free) | 1 - 2 | 10 kΩ or higher |
Reconnect the clutch start switch connector.
|
| ||||
| NG | |
| 3.REPLACE PARK/NEUTRAL POSITION SWITCH OR CLUTCH START SWITCH |
| NEXT | |
| 4.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL) |
Connect an intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Select the following menu items: Powertrain / Engine and ECT / Data List / Starter Signal.
Read the value displayed on the tester when the ignition switch is turned to ON and the engine starts.
| Conditions | Starter Signal |
| Ignition switch to ON | OFF |
| Engine start | ON |
|
| ||||
| NG | |
| 5.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY |
![]() |
Disconnect the D8 ignition switch connector.
Check the resistance.
| Ignition Switch Positions | Tester Connections | Specified Conditions |
| LOCK | All Terminals | 10 kΩ or higher |
| ACC | 2 - 4 | Below 1 Ω |
| ON | 1 - 2, 1 - 4, 2 - 4, 5 - 6 | |
| START | 1 - 3, 1 - 4, 3 - 4, 5 - 6, 5 - 7, 6 - 7 |
Reconnect the ignition switch connector.
|
| ||||
| NG | |
| 6.REPLACE IGNITION OR STARTER SWITCH ASSEMBLY |
| NEXT | |
| 7.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL) |
Connect an intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Select the following menu items: Powertrain / Engine and ECT / Data List / Starter Signal.
Read the value displayed on the tester when the ignition switch is turned to ON and the engine starts.
| Conditions | Starter Signal |
| Ignition switch to ON | OFF |
| Engine start | ON |
|
| ||||
| NG | |
| 8.REPAIR OR REPLACE HARNESS OR CONNECTOR (PNP SWITCH OR CLUTCH START SWITCH - STA TERMINAL OF ECM) |
| NEXT | |
| 9.CHECK WHETHER DTC OUTPUT RECURS (DTC P0617) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Clear DTCs (Click here).
Drive the vehicle at more than 20 km/h (12.4 mph) for over 20 seconds.
Select the following menu items: Powertrain / Engine and ECT/ DTC.
Read DTCs.
| Display (DTC Output) | Proceed To |
| P0617 | A |
| No DTC | B |
|
| ||||
| A | ||
| ||