Home › ENGINE · 1NZ-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0100    Mass or Volume Air Flow Circuit

DTC    P0102    Mass or Volume Air Flow Circuit Low Input

DTC    P0103    Mass or Volume Air Flow Circuit High Input

for Preparation Click here


DESCRIPTION

The Mass Air Flow (MAF) meter is a sensor that measures the amount of air flowing through the throttle valve.
The ECM uses this information to determine the fuel injection time and to provide the appropriate air-fuel ratio.
Inside the MAF meter, there is a heated platinum wire which is exposed to the flow of intake air.
By applying a specific electrical current to the wire, the ECM heats it to a given temperature. The flow of incoming air cools both the wire and an internal thermistor, affecting their resistance. To maintain a constant current value, the ECM varies the voltage applied to these components in the MAF meter. The voltage level is proportional to the airflow through the sensor, and the ECM uses it to calculate the intake air volume.
The circuit is constructed so that the platinum hot wire and the temperature sensor create a bridge circuit, and the power transistor is controlled so that the potentials of A and B remain equal to maintain the predetermined temperature.

HINT:
When any of these DTCs are set, the ECM enters fail-safe mode. During fail-safe mode, the ignition timing is calculated by the ECM, according to the engine RPM and throttle valve position. Fail-safe mode continues until a pass condition is detected.


A122492E01


DTC No.
DTC Detection Conditions
Trouble Areas
P0100
MAF meter voltage less than 0.2 V, or more than 4.9 V for 3 seconds
(1 trip detection logic)
  1. Open or short in MAF meter circuit
  2. MAF meter
  3. ECM
P0102
MAF meter voltage less than 0.2 V for 3 seconds
(1 trip detection logic)
P0103
MAF meter voltage more than 4.9 V for 3 seconds
(1 trip detection logic)

HINT:
When any of these DTCs are set, check the air-flow rate by selecting the following menu items on an intelligent tester: Powertrain / Engine and ECT / Data List / MAF.

Mass Air Flow Rate (g/sec)
Malfunctions
Approximately 0.0
  1. Open in Mass Air Flow (MAF) meter power source circuit
  2. Open or short in VG circuit
271.0 or more
  1. Open in EVG circuit


WIRING DIAGRAM


A128485E01


INSPECTION PROCEDURE

HINT:
Read freeze frame data using an intelligent tester. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data, from the time the malfunction occurred.

1.READ VALUE USING INTELLIGENT TESTER (MASS AIR FLOW RATE)
  1. Connect an intelligent tester to the DLC3.

  1. Start the engine and turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / MAF.

  1. Read the values displayed on the tester.

    Result:
    Mass Air Flow Rate (g/sec)
    Proceed To
    0.0
    A
    271.0 or more
    B
    Between 1.0 and 270.0 (*1)
    C

    *1: The value must be changed when the throttle valve is open or closed with the engine running.



B
Go to step 6

C
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A


2.INSPECT MASS AIR FLOW METER (POWER SOURCE VOLTAGE)
A054396E39
  1. Disconnect the C26 Mass Air Flow (MAF) meter connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage between the terminal of the wire harness side connector and body ground.

    Standard voltage:
    Tester Connections
    Specified Conditions
    +B (C26-1) - Body ground
    9 to 14 V

  1. Reconnect the MAF meter connector.



NG
Go to step 5
OK


3.INSPECT MASS AIR FLOW METER (VG VOLTAGE)
A112625E01
  1. Output voltage inspection.

    1. Disconnect the C26 MAF meter connector.

    2. Apply battery voltage across terminals +B and E2G.

    3. Connect the positive (+) tester probe to terminal VG, and negative (-) tester probe to terminal E2G.

    4. Check the voltage.

      Standard voltage:
      Tester Connections
      Specified Conditions
      VG (3) - E2G (2)
      0.2 to 4.9 V

    5. Reconnect the MAF meter connector.



NG
REPLACE MASS AIR FLOW METER (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
A107856E13
  1. Disconnect the C26 MAF meter connector.

  1. Disconnect the C20 ECM connector.

  1. Check the resistance.

    Standard resistance (Check for open):
    Tester Connections
    Specified Conditions
    VG (C26-3) - VG (C20-118)
    Below 1 Ω
    E2G (C26-2) - E2G (C20-116)

    Standard resistance (Check for short):
    Tester Connections
    Specified Conditions
    VG (C26-3) or VG (C20-118) - Body ground
    10 kΩ or higher

  1. Reconnect the MAF meter connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)  

5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - INTEGRATION RELAY)
A112609E01
  1. Disconnect the C26 MAF meter connector.

  1. Remove the integration relay from the engine room relay block.

  1. Check the resistance.

    Standard resistance (Check for open):
    Tester Connections
    Specified Conditions
    +B (C26-1) - 1A-4
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connections
    Specified Conditions
    +B (C26-1) or 1A-4 - Body ground
    10 kΩ or higher

  1. Reconnect the MAF meter connector.

  1. Reinstall the integration relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CHECK ECM POWER SOURCE CIRCUIT (Click here)  

6.CHECK HARNESS AND CONNECTOR (SENSOR GROUND)


    A107942E01
  1. Disconnect the C26 MAF meter connector.

  1. Check the resistance.

    Standard resistance:
    Tester Connections
    Specified Conditions
    E2G (C26-2) - Body ground
    Below 1 Ω

  1. Reconnect the MAF meter connector.



OK
REPLACE MASS AIR FLOW METER (Click here)
NG


7.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
A107856E01
  1. Disconnect the C26 MAF meter connector.

  1. Disconnect the C20 ECM connector.

  1. Check the resistance.

    Standard resistance (Check for open):
    Tester Connections
    Specified Conditions
    VG (C26-3) - VG (C20-118)
    Below 1 Ω
    E2G (C26-2) - E2G (C20-116)

    Standard resistance (Check for short):
    Tester Connections
    Specified Conditions
    VG (C26-3) or VG (C20-118) - Body ground
    10 kΩ or higher

  1. Reconnect the MAF meter connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)