Home › STEERING › STEERING COLUMN › STEERING COLUMN ASSEMBLY (for Hatchback)

STEERING COLUMN ASSEMBLY (for Hatchback) > INSTALLATION

for Preparation Click here



1. INSTALL STEERING COLUMN ASSEMBLY
  1. Install the steering column assembly onto the instrument panel reinforcement assembly with the bolt and 2 nuts.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

  1. Connect all the connectors and clamp the wire harnesses onto the steering post assembly bracket.



2. INSTALL BRAKE PEDAL (for Automatic Transaxle)
  1. Apply MP grease No. 2 to the brake master cylinder push rod clevis pin and installation surfaces.

  1. Install the 2 brake pedal bushes, and install the brake pedal with the nut and brake pedal shaft.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }

  1. Apply MP grease No. 2 to the brake master cylinder push rod clevis pin and installation surfaces.

  1. Connect the brake master cylinder push rod clevis to the brake pedal with the brake master cylinder push rod clevis pin, install the clip onto the brake master cylinder push rod clevis pin, and then install the brake pedal return spring.



3. INSTALL BRAKE PEDAL SUPPORT SUB-ASSEMBLY (for Manual Transaxle)


C116881
  1. Install the pedal support with the bolt and 4 nuts.

    Torque:
    Bolt:
    24 N*m{ 241 kgf*cm , 17 ft.*lbf }
    Nut:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }



4. INSTALL BRAKE MASTER CYLINDER PUSH ROD CLEVIS (for Manual Transaxle)
  1. Apply lithium soap base glycol grease to the push rod pin.



    C116880
  1. Install the push rod clevis with the push rod pin and clip.

  1. Install the brake pedal return spring.



5. INSTALL NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY


G028410E06
  1. Connect all the connectors and clamp the wire harnesses onto the steering post assembly bracket.

  1. Align the matchmarks on No. 2 steering intermediate shaft assembly and the steering sliding yoke and provisionally install them with bolt C.
    Text in Illustration 
    *1
    Bolt A
    *2
    Bolt B
    *3
    Bolt C
    *a
    Matchmark

    Torque:
    35 N*m{ 360 kgf*cm , 26 ft.*lbf }

  1. Align the matchmarks on the steering sliding yoke and steering gear assembly and install them with bolt B.

    Torque:
    35 N*m{ 360 kgf*cm , 26 ft.*lbf }

  1. Tighten bolt A.

    Torque:
    35 N*m{ 360 kgf*cm , 26 ft.*lbf }



6. INSTALL COLUMN HOLE COVER SILENCER SHEET
  1. Install the column hole cover plate with the 2 clips.

  1. Install the floor carpet.



7. INSTALL INSTRUMENT PANEL UNDER TRAY (w/o Knee Airbag)


B108187
  1. Engage the 4 claws and install the instrument panel under tray.

  1. Install the 2 <A> screws.



    B108186
  1. Engage the 4 claws and install the instrument panel under tray.



8. INSTALL DRIVER SIDE KNEE AIRBAG ASSEMBLY (w/ Knee Airbag)


C125678E01
  1. Engage the 6 claws.

  1. Install the driver side knee airbag assembly with the 4 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Connect the airbag connector.

    NOTICE:
    Securely lock the locking button.



9. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    B114571
  1. Engage the 4 claws and install the instrument panel under cover.



10. CONNECT POWER STEERING ECU
  1. Connect the 2 steering post assembly connectors to the power steering ECU.

  1. Install the power steering motor harness and torque sensor wire harness clamps onto the side of the power steering ECU.

  1. Tilt the steering post assembly up and down to make sure that the power steering motor harness and torque sensor wire harness do not interfere with any components.



11. INSTALL INSTRUMENT PANEL SUB-ASSEMBLY UPPER


B108233E01
  1. Using a nipper, cut off both ends of the runner portion shown in the illustration (When installing a new one).

  1. Engage the 5 claws at the upper side of the instrument panel.



  1. Engage the claw and the 3 clips at the lower side of the instrument panel.


    B105355E01

  1. Install the instrument panel upper with the 2 <C> bolts and the 4 <B> screws.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf } for bolt



  1. Connect the connectors.


    B105354E01



    B108182
  1. Connect the passenger airbag connector and clamp.



12. INSTALL SWITCH BASE HOLE COVER


B108201
  1. Disengage the 2 clips and 2 claws and install the switch hole base.



13. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY


B105352
  1. Engage the claw of the hinge portion in the horizontal direction to install the glove compartment door assembly.

    NOTICE:
    Engage the claw in the horizontal direction, otherwise, installation failure caused by excessive play around the hinge portion will result.



    B108202
  1. Slightly deform the upper portion of the glove compartment door assembly to engage the stopper.



14. INSTALL FRONT PILLAR GARNISH RH


    B114342E01
  1. w/ Curtain Shield Airbag:

    1. Remove the piece of cloth or nylon.



    B127672
  1. w/ Front No. 2 Speaker:

    1. Insert the hook into the body hole.

    2. Engage the clip and install the front speaker.



    3. B127674
    4. Connect the speaker connector.



    B114312
  1. Install the 3 antenna cord clamps.

  1. Connect the connector.



  1. w/ Curtain Shield Airbag:



      B117697E01
    1. Install a new special clip and the clip onto a new front pillar garnish.

    2. Engage the 2 clips and the 2 claws and install the front pillar garnish.



  1. w/o Curtain Shield Airbag:



      B117694
    1. Engage the 2 clips and the 2 claws and install the front pillar garnish.



15. INSTALL FRONT PILLAR GARNISH LH


    B114344E01
  1. w/ Curtain Shield Airbag:

    1. Remove the piece of cloth or nylon.



    B127671
  1. w/ Front No. 2 Speaker:

    1. Insert the hook into the body hole.

    2. Engage the clip and install the front speaker.



    3. B127673
    4. Connect the speaker connector.



    B114316
  1. Install the 4 wire harness clamps.



  1. w/ Curtain Shield Airbag:



      B117698E01
    1. Install a new special clip and the clip onto a new front pillar garnish.

    2. Engage the 2 clips and the 2 claws and install the front pillar garnish.



  1. w/o Curtain Shield Airbag:



      B114318
    1. Engage the 2 clips and the 2 claws and install the front pillar garnish.



16. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH
  1. Install the front door opening trim weatherstrip.



17. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

HINT:
Use the same procedure for the RH side as for the LH side.



18. INSTALL INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY CENTER


B132366E01
  1. Fit the 3 A claws of the instrument cluster finish panel into the upper instrument cluster finish panel center.



    B132367
  1. Engage the 4 claws and 5 clips and install the instrument cluster finish panel.



19. INSTALL COMBINATION METER ASSEMBLY


E107730
  1. Install the combination meter assembly with the 2 screws.

  1. Connect the 2 connectors.



20. INSTALL NO. 1 INSTRUMENT CLUSTER FINISH PANEL


B132366E01
  1. Fit the 3 A claws of the instrument cluster finish panel into the upper instrument cluster finish panel center.



    B132367
  1. Engage the 4 claws and 5 clips and install the instrument cluster finish panel.



21. INSTALL INSTRUMENT PANEL FINISH PANEL END RH


E107743
  1. with CD player

    1. Connect the connector.

    2. Engage the 4 claws and 3 clips and install the instrument panel finish panel end RH.



    E107744
  1. Except CD player

    1. Connect the connector.

    2. Engage the 5 claws and 3 clips and install the instrument panel finish panel end RH.



22. INSTALL INSTRUMENT PANEL FINISH PANEL END LH


E107741
  1. with CD player

    1. Connect the connector.

    2. Engage the 4 claws and 3 clips and install the instrument panel finish panel end LH.



    E107742
  1. Except CD player

    1. Connect the connector.

    2. Engage the 5 claws and 3 clips and install the instrument panel finish panel end LH.



23. INSTALL COMBINATION SWITCH ASSEMBLY


C117206
  1. Install the turn signal switch assembly with spiral cable onto the steering post assembly with the clamp.

  1. Connect all the connectors to the turn signal switch with spiral cable.



24. INSTALL STEERING COLUMN COVER


    C117205E01
  1. Engage the claw to install the steering column upper cover.



    C117204E01
  1. Engage the 2 claws to install the steering column lower cover.

  1. Install the 3 screws.



25. INSTALL STEERING WHEEL ASSEMBLY


    C117210E02
  1. Align the matchmarks and install the steering wheel assembly onto the steering column assembly.
    Text in Illustration 
    *a
    Matchmark

  1. Install the nut.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }

  1. Connect all connectors to the spiral cable.



26. INSTALL STEERING PAD (w/o Steering Pad Switch)


C117196E01

NOTICE:
Do not use a steering pad that has been dropped.

  1. Confirm that the ignition switch is turned to off.

  1. Confirm that the negative battery terminal is detached.

    CAUTION:
    Do not begin the operation for at least 90 seconds after the negative battery terminal is detached.

  1. Connect the horn terminal.

  1. Connect the airbag connector.

    NOTICE:
    Securely lock the locking button.



    C121183
  1. Install the steering pad.

  1. Using "TORX" socket wrench T30, tighten the 2 bolts.

    Torque:
    8.8 N*m{ 90 kgf*cm , 78 in.*lbf }

    NOTICE:
    Tighten the 2 bolts while holding the steering pad to prevent it moving upward.



27. INSTALL STEERING PAD (w/ Steering Pad Switch)


C117200E01
  1. Connect the horn terminal.

  1. Connect the airbag connector.

    NOTICE:
    Securely lock the locking button.



    C121184
  1. Install the steering pad.

  1. Using "TORX" socket wrench T30, tighten the 2 bolts.

    Torque:
    8.8 N*m{ 90 kgf*cm , 78 in.*lbf }

    NOTICE:
    Tighten the 2 bolts while holding the steering pad to prevent it moving upward.



28. POSITION FRONT WHEEL FACING STRAIGHT AHEAD


29. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



30. CHECK SRS WARNING LIGHT TURNS OFF
(Click here)


31. PERFORM CALIBRATION OF TORQUE SENSOR ZERO POINT
(Click here)