Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › SPIRAL CABLE (for Sedan)

SPIRAL CABLE (for Sedan) > INSTALLATION

for Preparation Click here


CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (Click here).



1. INSTALL STEERING SENSOR (w/ VSC)


C108994E01
  1. Engage the 6 claws and insert the 2 pins into the holes to install the steering sensor onto the spiral cable.



2. INSTALL SPIRAL CABLE (w/ VSC)
  1. Check that the ignition switch is turned to off.

  1. Confirm that the cable is disconnected from the negative battery terminal.

    CAUTION:
    Do not begin the operation for at least 90 seconds after the disconnected from the negative battery terminal.

  1. Confirm that the front tires face straight forward.

  1. Confirm that the turn signal switch is in the neutral position.

    NOTICE:
    Perform the operation when the turn signal switch is in the neutral position. Otherwise, the pin of the turn signal will break.



    C139099
  1. Engage the 3 claws and install the spiral cable.

    NOTICE:
    Pull the lock pin out before installing the steering wheel, when replacing the spiral cable with a new one.



    B109372E02
  1. Connect the steering sensor connector.
    Text in Illustration 
    *1
    Housing

  1. Connect the airbag connector.

  1. Connect the horn connector.



3. INSTALL SPIRAL CABLE (w/o VSC)
  1. Check that the ignition switch is turned to off.

  1. Confirm that the cable is disconnected from the negative battery terminal.

    CAUTION:
    Do not begin the operation for at least 90 seconds after the disconnected from the negative battery terminal.

  1. Confirm that the front tires face straight forward.

  1. Confirm that the turn signal switch is in the neutral position.

    NOTICE:
    Perform the operation when the turn signal switch is in the neutral position. Otherwise, the pin of the turn signal will break.



    C139099
  1. Engage the 3 claws and install the spiral cable.

    NOTICE:
    Pull the lock pin out before installing the steering wheel, when replacing the spiral cable with a new one.



    B108278E02
  1. Connect the airbag connector.
    Text in Illustration 
    *1
    Housing

  1. Connect the horn connector.



4. INSTALL STEERING COLUMN COVER


    C139094E01
  1. Engage the 2 claws and install the steering column upper cover.



    C139093
  1. Engage the 2 claws and install the steering column lower cover.

  1. Tighten the 3 screws.



5. ADJUST SPIRAL CABLE


    B108279
  1. Center the spiral cable.

    1. Turn the spiral cable counterclockwise until it locks.

      HINT:
      The spiral cable turns a maximum of approximately 5 times.



    2. B108280E03
    3. Turn the spiral cable 2.5 times clockwise from its locked position and align the center marks.
      Text in Illustration 
      *1
      Center Mark



6. INSTALL STEERING WHEEL ASSEMBLY


    C139086E01
  1. Align the matchmarks and install the steering wheel assembly onto the steering column assembly.

  1. Install the nut.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }

  1. Connect all connectors to the spiral cable.



7. INSTALL STEERING PAD


C117196E02
Text in Illustration 
*1
Locking Button
  1. Connect the horn connector.

  1. Connect the airbag connector.

    NOTICE:
    1. Align the color of the airbag connector with that of the steering pad assembly, and install the airbag connector.
    2. Securely lock the locking button.



    C139083
  1. Install the steering pad.

  1. Using "TORX" socket wrench T30, tighten the 2 bolts.

    Torque:
    8.8 N*m{ 90 kgf*cm , 78 in.*lbf }



8. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



9. INSPECT SRS WARNING LIGHT
(Click here)