DTC P0171 System Too Lean (Bank 1) |
DTC P0172 System Too Rich (Bank 1) |
| DTC No. | DTC Detection Conditions | Trouble Areas |
| P0171 | With warm engine and stable air-fuel ratio feedback, fuel trim considerably in error to lean side (2 trip detection logic) |
|
| P0172 | With warm engine and stable air-fuel ratio feedback, fuel trim considerably in error to rich side (2 trip detection logic) |
|

| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0171 OR P0172) |
Connect an intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Select the following menu items: Powertrain / Engine and ECT / DTC.
Read DTCs.
| Display (DTC Output) | Proceed To |
| P0171 or P0172 | A |
| P0171 or P0172 and other DTCs | B |
|
| ||||
| A | |
| 2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME) |
Connect an intelligent tester to the DLC3.
Start the engine and turn the tester on.
Warm up the engine at an engine speed of 2,500 rpm for approximately 90 seconds.
Select the following menu items: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.
Perform the Active Test Control with the intelligent tester and check the heated oxygen sensor status.
| Case | Heated Oxygen Sensor (Sensor 1) Output Voltage | Heated Oxygen Sensor (Sensor 2) Output Voltage | Main Suspected Trouble Area |
| 1 | ![]() ![]() | ![]() ![]() | - |
| 2 | ![]() ![]() | ![]() ![]() |
|
| 3 | ![]() ![]() | ![]() ![]() |
|
| 4 | ![]() ![]() | ![]() ![]() |
|
| Result | Proceed To |
| Case 1 | C |
| Case 2 | B |
| Case 3 | A |
|
| ||||
|
| ||||
| A | |
| 3.READ VALUE USING INTELLIGENT TESTER (MAF) |
Connect an intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Select the following menu items: Powertrain / Engine and ECT / Data List / Coolant Temp and MAF.
Allow the engine to idle until the Coolant Temp reaches 75°C (167°F) or more.
Read the MAF with the engine in an idling condition and at an engine speed of 2,500 rpm.
|
| ||||
| OK | |
| 4.READ VALUE USING INTELLIGENT TESTER (COOLANT TEMP) |
Connect an intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Select the following menu items: Powertrain / Engine and ECT / Data List / Coolant Temp.
Read the Coolant Temp twice, when the engine is both cold and warmed up.
|
| ||||
| OK | |
| 5.CHECK PCV HOSE CONNECTIONS |
Check the PCV hose connections.
|
| ||||
| OK | |
| 6.CHECK AIR INDUCTION SYSTEM |
Check the air induction system for vacuum leakage.
|
| ||||
| OK | |
| 7.CHECK FOR SPARKS AND IGNITION |
![]() |
Disconnect the injector connectors, in order to prevent the engine from starting.
Install the spark plug onto the ignition coil.
Attach the spark plug assembly to the cylinder head.
Crank the engine for less than 2 seconds and check the spark.
Reconnect the injector connectors.
|
| ||||
| OK | |
| 8.CHECK FOR EXHAUST GAS LEAK |
Check for exhaust gas leakage.
|
| ||||
| OK | |
| 9.CHECK FUEL PRESSURE |
Check the fuel pressure .
|
| ||||
| OK | |
| 10.INSPECT FUEL INJECTOR ASSEMBLY (INJECTION AND VOLUME) |
Check the injection volume .
|
| ||||
| OK | |
| 11.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE) |
![]() |
Disconnect the C36 HO2 sensor (sensor 1) connector.
Check the resistance.
| Tester Connections | Specified Conditions |
| HT1A (1) - +B (2) | 5.3 to 7.5 Ω at 20 °C (68°F) |
| HT1A (1) - E2 (4) | 10 kΩ or higher |
Reconnect the HO2 sensor connector.
|
| ||||
| OK | |
| 12.INSPECT INTEGRATION NO.1 RELAY (EFI RELAY) |
![]() |
Remove the integration relay from the engine room relay block.
Inspect the EFI fuse.
Remove the EFI fuse from the integration relay.
Check the EFI fuse resistance.
Reinstall the EFI fuse.
Inspect the EFI relay.
Check the EFI relay resistance.
| Tester Connections | Specified Conditions |
| 1C-1 - 1A-4 | 10 kΩ or higher |
| Below 1 Ω (Apply battery voltage between terminals 1A-2 and 1A-3) |
Reinstall the integration relay.
|
| ||||
| OK | |
| 13.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR (SENSOR 1) - ECM) |
![]() ![]() |
Disconnect the C36 HO2 sensor connector.
Turn the ignition switch to ON.
Measure the voltage between the +B terminal of the HO2 sensor connector and the body ground.
| Tester Connections | Specified Conditions |
| +B (C36-2) - Body ground | 9 to 14 V |
Turn the ignition switch off.
Disconnect the C20 ECM connector.
Check the resistance.
| Tester Connections | Specified Conditions |
| HT1A (C36-1) - HT1A (C20-109) | Below 1 Ω |
| OX1A (C36-3) - OX1A (C20-112) | |
| E2 (C36-4) - EX1A (C20-90) |
| Tester Connections | Specified Conditions |
| HT1A (C36-1) or HT1A (C20-109) - Body ground | 10 kΩ or higher |
| OX1A (C36-3) or OX1A (C20-112) - Body ground | |
| E2 (C36-4) or EX1A- (C20-90) - Body ground |
Reconnect the ECM connector.
Reconnect the HO2 sensor connector.
|
| ||||
| OK | |
| 14.REPLACE HEATED OXYGEN SENSOR |
| NEXT | |
| 15.PERFORM CONFIRMATION DRIVING PATTERN |

| NEXT | |
| 16.CHECK WHETHER DTC OUTPUT RECURS (DTC P0171 OR P0172) |
Connect an intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Select the following menu items: Powertrain / Engine and ECT / DTC.
Read DTCs.
| Display (DTC Output) | Proceed To |
| No output | A |
| P0171 or P0172 | B |
|
| ||||
| A | ||
| ||