Home › BRAKE › BRAKE CONTROL › ANTI-LOCK BRAKE SYSTEM (for Sedan)

DTC    C0273/13    Open or Short Circuit in ABS Motor Relay Circuit

DTC    C0274/14    Short to B+ in ABS Motor Relay Circuit

for Preparation Click here


DESCRIPTION

The ABS motor relay supplies the power to the ABS pump motor. While the ABS is activated, the skid control ECU switches the motor relay ON and operates the ABS pump motor.

DTC No.
DTC Detecting Conditions
Trouble Areas
C0273/13
When either of following conditions (1 or 2) detected:
  1. All of following conditions continue for 0.2 seconds or more.
    1. IG1 terminal voltage between 9.5 V and 17.2 V.
    2. During initial check or ABS operation.
    3. Relay contact open when relay on.
  2. Both of following conditions continue for 0.2 seconds or more.
    1. IG1 terminal voltage 9.5 V or less.
    2. Relay contact remains open when relay on.
  1. ABS1/VSC1 fuse
  2. Wire harness (+BM circuit)
  3. Brake actuator
C0274/14
When motor relay off, motor relay remains closed for 4 seconds or more.
  1. ABS1/VSC1 fuse
  2. Wire harness (+BM circuit)
  3. Brake actuator

HINT:
C0273/13 and C0274/14: The skid control ECU begins to detect these DTCs when the vehicle speed exceeds 6 km/h (4 mph).


WIRING DIAGRAM

Click here.

INSPECTION PROCEDURE

1.INSPECT FUSE (ABS1/VSC1)


    C117863E05
  1. Remove the ABS1/VSC1 fuse from the engine room R/B.

  1. Measure the resistance.

    Standard Resistance:
    Below 1 Ω



NG
CHECK FOR SHORTS IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSE
OK


2.CHECK HARNESS AND CONNECTOR (BATTERY - SKID CONTROL ECU - BODY GROUND)
  1. Confirm that there are no defects in the skid control ECU connector fitting.

  1. Disconnect the skid control ECU connector.

  1. Inspect both the connector case and the terminal for deformation and corrosion.

    OK:
    No deformation or corrosion.



    C117862E02
  1. Measure the voltage.

    Standard Voltage:
    Tester Connection
    Specified Condition
    A15-23 (+BM) - Body ground
    11 to 14 V

  1. Measure the resistance.

    Standard Resistance:
    Tester Connection
    Specified Condition
    A15-2 (GND1) - Body ground
    Below 1 Ω
    A15-24 (GND2) - Body ground
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER


    A107926E08
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Clear the DTCs (Click here).

  1. Perform the active test using the intelligent tester.
    Select the following menu items: Chassis / ABS/VSC/TRC / Active Test.

    ACTIVE TEST: ABS 
    Item (Display)
    Vehicle Condition / Test Details
    Diagnostic Note
    Motor Relay
    Turns ABS motor relay ON / OFF
    Operating sound of motor can be heard

  1. Check the operation sound of the ABS motor when operating it with the intelligent tester.

    OK:
    The operation sound of the ABS motor can be heard.



NG
REPLACE BRAKE ACTUATOR
OK


4.RECONFIRM DTC
  1. Clear the DTC(s) (Click here).

  1. Start the engine.

  1. Drive the vehicle at 6 km/h (4 mph) or more to activate the initial check.

  1. Check if the same DTC(s) is output (Click here).

    Result
    Proceed to
    DTC output
    A
    DTC not output
    B



B
END
A

REPLACE BRAKE ACTUATOR