Home › HEATER & AIR CONDITIONING SYSTEM › AIR CONDITIONING › AIR CONDITIONING UNIT (for Hatchback)

AIR CONDITIONING UNIT (for Hatchback) > INSTALLATION

for Preparation Click here



1. INSTALL AIR CONDITIONING UNIT


I101189
  1. Install the air conditioning unit with the 3 screws.



2. INSTALL AIR CONDITIONING AMPLIFIER ASSEMBLY


I101243
  1. Install the air conditioning amplifier with the screw.



3. INSTALL INSTRUMENT PANEL REINFORCEMENT


I101241
  1. Provisionally tighten the air conditioning unit with the 3 screws.



    I101242
  1. Connect the connector and 3 clamps.



  1. Install the instrument panel reinforcement and the air conditioning unit with the 9 bolts.


    I101186



  1. Install the 3 screws, 3 bolts and nut in the sequence shown in the illustration.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf } for screw
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf } for nut
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf } for bolt



    I101545E01



  1. Install the wire harness with the clamps and connect the connectors (for LHD).


    I104813



  1. Install the wire harness with the clamps and connect the connectors (for RHD).


    I104814



  1. Engage the clamps (for LHD).


    I101182



  1. Engage the clamps (for RHD).


    I101184



  1. Connect the connectors (for LHD).


    I101604



  1. Connect the connectors (for RHD).


    I101605



    I101180
  1. Install the ground wire with the bolt.

    Torque:
    3.2 N*m{ 33 kgf*cm , 28 in.*lbf }



    I101179E01
  1. Install the drain hose into the position shown in the illustration.

    NOTICE:
    1. Install the drain hose with its UP mark facing upward, within the 90 degree range shown in the illustration.
    2. Install the drain hose without twisting it.



4. INSTALL CONNECTOR NO. 2 HOLDER


I100717
  1. Connect the connectors and install the wire harness.



    I101240
  1. Install the connector holder with the bolt.

    Torque:
    3.2 N*m{ 33 kgf*cm , 28 in.*lbf }



5. INSTALL MAIN BODY ECU (for LHD)


I101239
  1. Install the main body ECU with the 2 bolts.

    Torque:
    3.2 N*m{ 33 kgf*cm , 28 in.*lbf }



    I101238
  1. Connect the 5 connectors and the 3 clamps.



6. INSTALL MAIN BODY ECU (for RHD)


I101537
  1. Install the main body ECU with the 2 bolts.

    Torque:
    32 N*m{ 33 kgf*cm , 28 in.*lbf }



    I101536
  1. Connect the 5 connectors and the 5 clamps.



7. INSTALL INSTRUMENT PANEL BRACE SUB-ASSEMBLY (for LHD)


    I101593
  1. w/ Driver Side Knee Airbag:

    1. Install the instrument panel brace with the 2 bolts, screw and nut.

      Torque:
      9.8 N*m{ 100 kgf*cm , 87 in.*lbf } for screw
      9.8 N*m{ 100 kgf*cm , 87 in.*lbf } for nut
      9.8 N*m{ 100 kgf*cm , 87 in.*lbf } for bolt

    2. Engage the clamp.



    I101595
  1. w/o Driver Side Knee Airbag:

    1. Install the instrument panel brace with the bolt, screw and nut.

      Torque:
      9.8 N*m{ 100 kgf*cm , 87 in.*lbf } for screw
      9.8 N*m{ 100 kgf*cm , 87 in.*lbf } for nut
      9.8 N*m{ 100 kgf*cm , 87 in.*lbf } for bolt

    2. Engage the clamp.



8. INSTALL INSTRUMENT PANEL BRACE SUB-ASSEMBLY (for RHD)


    I101594
  1. w/ Driver Side Knee Airbag:

    1. Install the instrument panel brace with the 2 bolts, screw and nut.

      Torque:
      9.8 N*m{ 100 kgf*cm , 87 in.*lbf } for screw
      9.8 N*m{ 100 kgf*cm , 87 in.*lbf } for nut
      9.8 N*m{ 100 kgf*cm , 87 in.*lbf } for bolt

    2. Engage the 3 clamps.



    I101596
  1. w/o Driver Side Knee Airbag:

    1. Install the instrument panel brace with the bolt, screw and nut.

      Torque:
      9.8 N*m{ 100 kgf*cm , 87 in.*lbf } for screw
      9.8 N*m{ 100 kgf*cm , 87 in.*lbf } for nut
      9.8 N*m{ 100 kgf*cm , 87 in.*lbf } for bolt

    2. Engage the 3 clamps.



9. INSTALL DEFROSTER NOZZLE ASSEMBLY
  1. Engage the 5 claws and install the defroster nozzle.



  1. Connect the clamps and connectors and install the wire harness.


    I101175



10. INSTALL STEERING COLUMN ASSEMBLY
  1. Install the steering column assembly onto the instrument panel reinforcement assembly with the bolt and 2 nuts.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

  1. Connect all the connectors and clamp the wire harnesses onto the steering post assembly bracket.



11. INSTALL BRAKE PEDAL SUPPORT SUB-ASSEMBLY (for Manual Transaxle)


C116881
  1. Install the pedal support with the bolt and 4 nuts.

    Torque:
    Bolt:
    24 N*m{ 241 kgf*cm , 17 ft.*lbf }
    Nut:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }



12. INSTALL BRAKE MASTER CYLINDER PUSH ROD CLEVIS (for Manual Transaxle)
  1. Apply lithium soap base glycol grease to the push rod pin.



    C116880
  1. Install the push rod clevis with the push rod pin and clip.

  1. Install the brake pedal return spring.



13. INSTALL BRAKE PEDAL (for Automatic Transaxle)
  1. Apply MP grease No. 2 to the brake master cylinder push rod clevis pin and installation surfaces.

  1. Install the 2 brake pedal bushes, and install the brake pedal with the nut and brake pedal shaft.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }

  1. Apply MP grease No. 2 to the brake master cylinder push rod clevis pin and installation surfaces.

  1. Connect the brake master cylinder push rod clevis to the brake pedal with the brake master cylinder push rod clevis pin, install the clip onto the brake master cylinder push rod clevis pin, and then install the brake pedal return spring.



14. INSTALL STEERING SLIDING YOKE SUB-ASSEMBLY


C118005E04
  1. Align the matchmarks and install the sliding yoke onto the power steering assembly with bolt B.

    Torque:
    35 N*m{ 360 kgf*cm , 26 ft.*lbf }

  1. Tighten bolt A.

    Torque:
    35 N*m{ 360 kgf*cm , 26 ft.*lbf }



15. INSTALL COLUMN HOLE COVER SILENCER SHEET
  1. Install the column hole cover plate with the 2 clips.

  1. Install the floor carpet.



16. CONNECT POWER STEERING ECU
  1. Connect the 2 steering post assembly connectors to the power steering ECU.

  1. Install the power steering motor harness and torque sensor wire harness clamps onto the side of the power steering ECU.

  1. Tilt the steering post assembly up and down to make sure that the power steering motor harness and torque sensor wire harness do not interfere with any components.



17. INSTALL COMBINATION SWITCH ASSEMBLY


C117206
  1. Install the turn signal switch assembly with spiral cable onto the steering post assembly with the clamp.

  1. Connect all the connectors to the turn signal switch with spiral cable.



18. INSTALL STEERING COLUMN COVER


    C117205E01
  1. Engage the claw to install the steering column upper cover.



    C117204E01
  1. Engage the 2 claws to install the steering column lower cover.

  1. Install the 3 screws.



19. INSTALL STEERING WHEEL ASSEMBLY


    C117210E02
  1. Align the matchmarks and install the steering wheel assembly onto the steering column assembly.
    Text in Illustration 
    *a
    Matchmark

  1. Install the nut.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }

  1. Connect all connectors to the spiral cable.



20. INSTALL STEERING PAD
  1. w/o Steering Pad Switch:

    1. Install the steering pad.

  1. w/ Steering Pad Switch:

    1. Install the steering pad.



21. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY


    B108232E01
  1. Using a nipper, cut off both ends of the runner portion shown in the illustration (When installing a new one).

  1. w/ Driver Side Knee Airbag

    1. Apply butyl tape to install a new instrument panel safety pad No. 1 onto the instrument panel lower (When installing a new one).

    2. Apply butyl tape to install a new instrument panel safety pad No. 2 onto the instrument panel lower (When installing a new one).

  1. Install the lower instrument panel with the 5 <D> bolts, 2 <E> bolts, screw <G> and screw <H>.

    NOTICE:
    Do not excessively tighten the <D> bolts, otherwise, it may damage the area not being tightened.



  1. Connect the clamps and connectors.


    B108193E01



    B108192
  1. Engage the 2 claws to connect the DLC3 connector.



22. CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY


B108191
  1. Engage the 3 claws to connect the control lever.



23. CONNECT ANTENNA CORD SUB-ASSEMBLY


B108200
  1. for LHD:

    1. Connect the 2 antenna cord clamps.



    B108160E01
  1. for RHD:

    1. Connect the 3 antenna cord clamps.



24. INSTALL NO. 6 HEATER TO REGISTER DUCT ASSEMBLY


B108190
  1. Engage the 4 claws and install the heater to register duct.



25. INSTALL INSTRUMENT PANEL BOX


B108189E01
  1. Insert the stopper of the instrument panel box from the cutout of the instrument panel lower.

  1. Engage the 2 hinges with the instrument panel open.

  1. Close the instrument panel box.



26. INSTALL DRIVER SIDE KNEE AIRBAG ASSEMBLY (w/ Driver Side Knee Airbag)


C125678E01
  1. Engage the 6 claws.

  1. Install the driver side knee airbag assembly with the 4 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Connect the airbag connector.

    NOTICE:
    Securely lock the locking button.



27. INSTALL STEERING COLUMN COVER (w/ Driver Side Knee Airbag)


    C117205E01
  1. Engage the claw to install the steering column upper cover.



    C117204E01
  1. Engage the 2 claws to install the steering column lower cover.

  1. Install the 3 screws.



28. INSTALL INSTRUMENT PANEL UNDER TRAY


B108187
  1. Engage the 4 claws and install the instrument panel under tray.

  1. Install the 2 <A> screws.



    B108186
  1. Engage the 4 claws and install the instrument panel under tray.



29. INSTALL CONSOLE BOX ASSEMBLY REAR


B118993
  1. Engage the 2 clips and install the console box rear.

  1. Install bolt <F>.



30. INSTALL CONSOLE BOX CARPET


B118992
  1. Install the console box carpet.



31. INSTALL CONSOLE BOX COVER REAR


B118991
  1. Engage the 8 claws and install the console box rear cover.



32. INSTALL SHIFTING HOLE COVER SUB-ASSEMBLY (for Manual Transaxle)


B208631
  1. Engage the 6 claws and install the shifting hole cover.



33. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transaxle)


B208628
  1. Install the shift lever knob.



34. INSTALL COWL SIDE TRIM BOARD RH


    B114285
  1. Engage the claw and stud bolt and install the cowl side trim board.



35. INSTALL COWL SIDE TRIM BOARD LH

HINT:
Use the same procedure as for the RH side.



36. INSTALL INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY LH


    B114571
  1. Engage the 4 claws and install the instrument panel under cover.



37. INSTALL INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY RH


    B114572
  1. Engage the 3 claws and install the instrument panel under cover.

  1. Tighten the 2 screws.



38. INSTALL FRONT DOOR SCUFF PLATE RH


    B114284
  1. Engage the 8 claws and install the front door scuff plate.



39. INSTALL FRONT DOOR SCUFF PLATE LH

HINT:
Use the same procedure as for the RH side.



40. INSTALL UPPER INSTRUMENT PANEL SUB-ASSEMBLY


B108233E01
  1. Using a nipper, cut off both ends of the runner portion shown in the illustration (When installing a new one).

  1. Engage the 5 claws at the upper side of the instrument panel.



  1. Engage the claw and the 3 clips at the lower side of the instrument panel.


    B105355E01

  1. Install the instrument panel upper with the 2 <C> bolts and the 4 <B> screws.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf } for bolt



  1. Connect the connectors.


    B105354E01



    B108182
  1. Connect the passenger airbag connector and clamp.



41. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY


B105352
  1. Engage the claw of the hinge portion in the horizontal direction to install the glove compartment door assembly.

    NOTICE:
    Engage the claw in the horizontal direction, otherwise, installation failure caused by excessive play around the hinge portion will result.



    B108202
  1. Slightly deform the upper portion of the glove compartment door assembly to engage the stopper.



42. INSTALL NO. 1 SWITCH HOLE BASE


B108201
  1. Disengage the 2 clips and 2 claws and install the switch hole base.



43. INSTALL FRONT PILLAR GARNISH RH


    B114342E01
  1. w/ Curtain Shield Airbag:

    1. Remove the piece of cloth or nylon.



    B127672
  1. w/ Front No. 2 Speaker:

    1. Insert the hook into the body hole.

    2. Engage the clip and install the front speaker.



    3. B127674
    4. Connect the speaker connector.



    B114312
  1. Install the 3 antenna cord clamps.

  1. Connect the connector.



  1. w/ Curtain Shield Airbag:



      B117697E01
    1. Install a new special clip and the clip onto a new front pillar garnish.

    2. Engage the 2 clips and the 2 claws and install the front pillar garnish.



  1. w/o Curtain Shield Airbag:



      B117694
    1. Engage the 2 clips and the 2 claws and install the front pillar garnish.



44. INSTALL FRONT PILLAR GARNISH LH


    B114344E01
  1. w/ Curtain Shield Airbag:

    1. Remove the piece of cloth or nylon.



    B127671
  1. w/ Front No. 2 Speaker:

    1. Insert the hook into the body hole.

    2. Engage the clip and install the front speaker.



    3. B127673
    4. Connect the speaker connector.



    B114316
  1. Install the 4 wire harness clamps.



  1. w/ Curtain Shield Airbag:



      B117698E01
    1. Install a new special clip and the clip onto a new front pillar garnish.

    2. Engage the 2 clips and the 2 claws and install the front pillar garnish.



  1. w/o Curtain Shield Airbag:



      B114318
    1. Engage the 2 clips and the 2 claws and install the front pillar garnish.



45. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH
  1. Install the front door opening trim weatherstrip.



46. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH
  1. Install the front door opening trim weatherstrip.



47. CONNECT AIR INLET DAMPER CONTROL CABLE SUB-ASSEMBLY


I101159
  1. Engage the 2 claws and connect the air inlet damper control cable.



48. CONNECT DEFROSTER DAMPER CONTROL CABLE SUB-ASSEMBLY


I101158
  1. Engage the 2 claws and connect the defroster damper control cable.



49. CONNECT AIR MIX DAMPER CONTROL CABLE SUB-ASSEMBLY


I101157
  1. Engage the 2 claws and connect the air mix control cable clamp.

  1. Connect the defroster damper control cable to the clamp.



50. INSTALL AIR CONDITIONER PANEL SUB-ASSEMBLY


I101156
  1. Connect the 3 connectors and the clamp.



    I101155
  1. Engage the 3 clips and 2 claws and install the air conditioning panel.



51. INSTALL RADIO TUNER OPENING COVER (w/o Radio Receiver)


B108169
  1. Install the radio tuner opening cover with the 4 bolts.



52. INSTALL RADIO RECEIVER ASSEMBLY


E116762
  1. w/ Cassette Tape Player:

    1. Connect the connectors.

    2. Install the radio receiver with the 4 screws.



    I101590
  1. w/ CD Player:

    1. Connect the connectors.

    2. Engage the 4 clips and 2 claws and install the radio receiver.

    3. Install the 4 screws.



53. INSTALL INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY CENTER (Except CD Player)


E116764
  1. Engage the 4 clips and 2 claws and install the instrument cluster finish panel.



54. INSTALL COMBINATION METER ASSEMBLY


E107730
  1. Install the combination meter assembly with the 2 screws.

  1. Connect the 2 connectors.



55. INSTALL INSTRUMENT CLUSTER FINISH PANEL NO.1


B132366E01
  1. Fit the 3 A claws of the instrument cluster finish panel into the upper instrument cluster finish panel center.



    B132367
  1. Engage the 4 claws and 5 clips and install the instrument cluster finish panel.



56. INSTALL INSTRUMENT PANEL FINISH PANEL END RH


E107743
  1. with CD player

    1. Connect the connector.

    2. Engage the 4 claws and 3 clips and install the instrument panel finish panel end RH.



    E107744
  1. Except CD player

    1. Connect the connector.

    2. Engage the 5 claws and 3 clips and install the instrument panel finish panel end RH.



57. INSTALL INSTRUMENT PANEL FINISH PANEL END LH


E107741
  1. with CD player

    1. Connect the connector.

    2. Engage the 4 claws and 3 clips and install the instrument panel finish panel end LH.



    E107742
  1. Except CD player

    1. Connect the connector.

    2. Engage the 5 claws and 3 clips and install the instrument panel finish panel end LH.



58. CONNECT HEATER WATER HOSE INLET A


I101173E01
  1. Install the heater water inlet hose onto the heater unit.

    NOTICE:
    Perform the installation with the hose clip and mark at the correct angle as shown in the illustration.



59. CONNECT HEATER WATER OUTLET HOSE A (FROM HEATER UNIT)


I101172E01
  1. Install the heater water outlet hose onto the heater unit.

    NOTICE:
    Perform the installation with the hose clip and mark at the correct angle as shown in the illustration.



60. INSTALL LIQUID TUBE SUB-ASSEMBLY
  1. Remove the vinyl tape from liquid tube and the connecting portion of the unit.

  1. Apply sufficient compressor oil (ND-OIL8) to a new O-ring and the connecting part of liquid tube.

    Compressor oil:
    ND-OIL8 or the equivalent

  1. Install the O-ring onto liquid tube.

  1. connect liquid tube to the unit.



61. INSTALL SUCTION TUBE SUB-ASSEMBLY
  1. Remove the vinyl tape from the suction tube and the connecting part of the unit.

  1. Apply sufficient compressor oil (ND-OIL8) to a new O-ring and the connecting part of the suction tube.

    Compressor oil:
    ND-OIL8 or the equivalent

  1. Install the O-ring onto the suction tube.



    I101237
  1. Insert the tube joints securely into the fitting holes and tighten the bolt.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }



62. INSTALL COWL TOP PANEL OUTER


A108438
  1. Disengage the wire harness clamp.



    A115392
  1. Remove the 9 bolts and remove the cowl top panel outer.



63. INSTALL NO. 2 COWL TO REGISTER DUCT SUB-ASSEMBLY


A108951
  1. Disengage the claw and remove cowl to register duct sub-assembly No. 2.



64. INSTALL FRONT WIPER MOTOR AND LINK


E113861
  1. Connect the connector.

  1. Slide the wiper link as shown in the illustration and engage the rubber pin with the body.

  1. Install the front wiper motor and link with the 2 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



65. INSTALL COWL TOP VENTILATOR LOUVER LH (for LHD)


E113853
  1. Engage the 4 claws and install the cowl top ventilator louver LH.

  1. Install the 2 clips.



66. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for LHD)


E113854
  1. Connect the washer hose.



    E113852
  1. Engage the 11 claws and install the cowl top ventilator louver sub-assembly.

  1. Install the clip.

  1. Connect the washer hose.



    E117641
  1. Engage the 2 hooks and install cowl top ventilator louver center No. 1.



67. INSTALL COWL TOP VENTILATOR LOUVER LH (for RHD)


E113856
  1. Engage the 4 claws and install the cowl top ventilator louver LH.

  1. Install the clip.



68. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for RHD)


E113855
  1. Engage the 10 claws and install the cowl top ventilator louver sub-assembly.

  1. Install the clip.

  1. Connect the washer hose.



69. INSTALL HOOD TO COWL TOP SEAL


E113851
  1. Engage the 7 clips and install the hood to cowl top seal.



70. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH


E058837E10
  1. Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.



    E113862E01
  1. Align the blade tip with the mark on the windshield glass, as shown in the illustration.

  1. Tighten the nut of the front wiper arm.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }



71. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH


E058837E10
  1. Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.



    E113863E01
  1. Align the blade tip with the mark on the windshield glass, as shown in the illustration.

  1. Tighten the nut of the front wiper arm.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }



72. INSTALL FRONT WIPER ARM HEAD CAP


E113849
  1. Engage the claw and install the 2 front wiper arm head caps.



73. ADD ENGINE COOLANT (for 1NZ-FE)
  1. Tighten all the plugs.

  1. Pour engine coolant into the radiator assembly until it overflows.

    Capacity:
    M/T 4.8 liters (5.1 USqts, 4.5 lmp. qts)
    A/T 4.7 liters (5.0 USqts, 4.4 lmp. qts)

    NOTICE:
    Do not substitute water for engine coolant.

    HINT:
    1. Use of improper engine coolant may damage the engine coolant system.
    2. Use only Toyota Super Long Life Coolant or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, and non-borate engine coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).

  1. Check the engine coolant level inside the radiator assembly by squeezing the inlet and outlet radiator hoses several times by hand. If the engine coolant level goes down, add engine coolant.

  1. Install the radiator cap sub-assembly securely.

  1. Slowly pour engine coolant into the radiator reservoir until it reaches the FULL line.

  1. Warm up the engine until the cooling fan operates.

    1. Set the air conditioning as follows while warming up the engine.

      Item
      Manual air conditioning system
      Automatic air conditioning system
      Set control as follows
      Fan speed - Any setting except "OFF"
      Temperature - Toward WARM
      Air conditioning switch "OFF"
      Fan speed - Any setting except "OFF"
      Temperature - To the highest temperature
      Air conditioning switch "OFF"
      "AUTO" switch "OFF"

    2. Maintain the engine speed at 2,000 to 2,500 rpm and warm up the engine until the cooling fan operates.

  1. Stop the engine and wait until the coolant cools down.

  1. If the engine coolant level is below the full level, perform steps (b) through (g) again and repeat the operation until the engine coolant level stays at the full level.

  1. Recheck the engine coolant level inside the radiator reservoir tank assembly. If it is below the full level, add the engine coolant.

  1. Visually check for engine coolant leakage.



74. ADD ENGINE COOLANT (for 2NZ-FE)
  1. Tighten all the plugs.

  1. Pour engine coolant into the radiator assembly until it overflows.

    Capacity:
    w/o Fan Shroud Ventilation Duct: M/T 4.9 liters (5.2 USqts, 4.6 lmp. qts)
    w/o Fan Shroud Ventilation Duct: A/T 4.8 liters (5.1 USqts, 4.5 lmp. qts)
    w/ Fan Shroud Ventilation Duct: M/T 5.1 liters (5.4 USqts, 4.7 lmp. qts)
    w/ Fan Shroud Ventilation Duct: A/T 5.0 liters (5.3 USqts, 4.6 lmp. qts)

    NOTICE:
    Do not substitute water for engine coolant.

    HINT:
    1. Use of improper engine coolant may damage the engine coolant system.
    2. Use only Toyota Super Long Life Coolant or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, and non-borate engine coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).

  1. Check the engine coolant level inside the radiator assembly by squeezing the inlet and outlet radiator hoses several times by hand. If the engine coolant level goes down, add engine coolant.

  1. Install the radiator cap sub-assembly securely.

  1. Slowly pour engine coolant into the radiator reservoir until it reaches the FULL line.

  1. Warm up the engine until the cooling fan operates.

    1. Set the air conditioning as follows while warming up the engine.

      Item
      Manual air conditioning system
      Automatic air conditioning system
      Set control as follows
      Fan speed - Any setting except "OFF"
      Temperature - Toward WARM
      Air conditioning switch "OFF"
      Fan speed - Any setting except "OFF"
      Temperature - To the highest temperature
      Air conditioning switch "OFF"
      "AUTO" switch "OFF"

    2. Maintain the engine speed at 2,000 to 2,500 rpm and warm up the engine until the cooling fan operates.

  1. Stop the engine and wait until the coolant cools down.

  1. If the engine coolant level is below the full level, perform steps (b) through (g) again and repeat the operation until the engine coolant level stays at the full level.

  1. Recheck the engine coolant level inside the radiator reservoir tank assembly. If it is below the full level, add the engine coolant.



75. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



76. CHECK SRS WARNING LIGHT
(Click here)


77. CHARGE REFRIGERANT



I100449E02

NOTICE:
Charge refrigerant in accordance with the equipment manual.

  1. Perform vacuum purging using a vacuum pump.

  1. Charge refrigerant HFC-134a (R134a).

    SST
    09985-20010   (09985-02010, 09985-02050, 09985-02060, 09985-02070, 09985-02080, 09985-02090, 09985-02110, 09985-02130, 09985-02140, 09985-02150)

    Standard:
    330 to 390 g (11.64 to 13.76 oz.) w/o Fan Shroud Ventilation Duct
    350 to 410 g (12.35 to 14.46 oz.) w/ Fan Shroud Ventilation Duct

    NOTICE:
    Do not start the engine before charging it with refrigerant as the cooler compressor doesn't work properly without sufficient refrigerant. This could cause the compressor to overheat.

    HINT:

    1. The relationship between the refrigerant charge amount and the pressure is as follows.


      I101544E02

    2. High Charge Range:
      If the refrigerant is overcharged, the pressure rises on the high-pressure side. High-pressure cut off frequently occurs. This causes insufficient cooling performance and also insufficient compressor lubrication.
    3. Low Charge Range:
      Shortage of refrigerant causes insufficient cooling performance and low circulation of refrigerant oil, which shortens the compressor life. Operation with insufficient coolant raises the refrigerant temperature and causes heat deterioration of the rubber seals and hoses. Cracking and thus refrigerant leakage may occur.


    1. Install the caps onto the service valves on the refrigerant line.



78. WARM UP ENGINE

NOTICE:
Warm up the engine at less than 2000 rpm for 1 minute or more after charging it with refrigerant.



79. CHECK FOR ENGINE COOLANT LEAK (for 1NZ-FE)

CAUTION:
To avoid the danger of being burned, do not remove the radiator cap sub-assembly while the engine and radiator assembly are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator assembly.



    A106594
  1. Fill the radiator assembly with engine coolant, then attach a radiator cap tester.

  1. Pump the tester to 137 kPa (1.4 kgf/cm2, 19.9 psi), then check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator assembly and water pump assembly for leakage. If there are no signs or traces of external engine coolant leakage, check the heater core, cylinder block and head.



80. CHECK FOR ENGINE COOLANT LEAK (for 2NZ-FE)

CAUTION:
To avoid the danger of being burned, do not remove the radiator cap sub-assembly while the engine and radiator assembly are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator assembly.



    A106594
  1. Fill the radiator assembly with engine coolant, then attach a radiator cap tester.

  1. Pump the tester to 137 kPa (1.4 kgf/cm2, 19.9 psi), then check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator assembly and water pump assembly for leakage. If there are no signs or traces of external engine coolant leakage, check the heater core, cylinder block and head.



81. CHECK FOR REFRIGERANT LEAK
  1. After recharging the refrigerant gas, check for refrigerant gas leakage using a halogen leak detector.

  1. Perform the operation as follows:

    1. Stop the engine.
    2. Secure good ventilation (the halogen leak detector may react to volatile gases other than refrigerant, such as evaporated gasoline or exhaust gas).
    3. Repeat the test 2 or 3 times.
    4. Make sure that some refrigerant remains in the refrigeration system.
      When the compressor is off: approximately 392 to 588 kPa (4 to 6 kgf*cm2, 57 to 85 psi)

    HINT:
    It is impossible for the above pressure to be maintained if there is leakage.



    I101569E02
  1. Using the halogen leak detector, check the refrigerant line, especially at the connection points, for leakage.



    I100587E02
  1. Bring the halogen leak detector close to the drain hose before performing the test.

    HINT:
    1. After the blower motor has stopped, leave the cooling unit for at least 15 minutes.
    2. Place the halogen leak detector sensor under the drain hose.
    3. When bringing the halogen leak detector close to the drain hose, make sure that the halogen leak detector does not react to the volatile gases.

    If such a reaction is unavoidable, the vehicle must be lifted up.

  1. If no gas leakage is detected from the drain hose, remove the blower motor from the cooling unit. Insert the halogen leak detector sensor into the unit and perform the test.

  1. Disconnect the pressure switch connector and leave it for approximately 20 minutes. Bring the halogen leak detector close to the pressure switch and perform the test.



82. POSITION FRONT WHEELS FACING STRAIGHT AHEAD


83. PERFORM CALIBRATION OF TORQUE SENSOR ZERO POINT
(Click here)