AIR CONDITIONING UNIT (for Sedan) > INSTALLATION |
| 1. INSTALL AIR CONDITIONING UNIT |
![]() |
Install the air conditioning unit with the 3 screws.
| 2. INSTALL AIR CONDITIONING AMPLIFIER ASSEMBLY |
![]() |
Install the air conditioning amplifier with the screw.
| 3. INSTALL INSTRUMENT PANEL REINFORCEMENT |
![]() |
Provisionally tighten the air conditioning unit with the 3 screws.
Install the instrument panel reinforcement and the air conditioning unit with the 9 bolts.

Install the 3 screws, 3 bolts and nut in the sequence shown in the illustration.

Install the wire harness with the clamps and connect the connectors (for LHD).

Install the wire harness with the clamps and connect the connectors (for RHD).

Engage the clamps (for LHD).

Engage the clamps (for RHD).

![]() |
Install the ground wire with the bolt.
![]() |
Install the drain hose into the position shown in the illustration.
| 4. INSTALL CONNECTOR NO. 2 HOLDER |
![]() |
Connect the connectors and install the wire harness.
![]() |
Install the connector holder with the bolt.
| 5. INSTALL MAIN BODY ECU (DRIVER SIDE J/B) (for LHD) |
![]() |
Install the main body ECU with the 2 bolts.
![]() |
Connect the 5 connectors and the 3 clamps.
| 6. INSTALL MAIN BODY ECU (DRIVER SIDE J/B) (for RHD) |
![]() |
Install the main body ECU with the 2 bolts.
![]() |
Connect the 5 connectors and the 5 clamps.
| 7. INSTALL INSTRUMENT PANEL BRACE SUB-ASSEMBLY (for LHD) |
![]() |
Install the instrument panel brace with the bolt, screw and nut.
Engage the clamp.
| 8. INSTALL INSTRUMENT PANEL BRACE SUB-ASSEMBLY (for RHD) |
![]() |
Install the instrument panel brace with the bolt, screw and nut.
Engage the 3 clamps.
| 9. INSTALL DEFROSTER NOZZLE ASSEMBLY |
![]() |
Engage the 5 claws and install the defroster nozzle.
Connect the 3 clamps and connector and install the wire harness.
| 10. INSTALL HEATER TO REGISTER DUCT ASSEMBLY |
![]() |
Engage the 3 claws and install the heater to register duct.
| 11. INSTALL STEERING COLUMN ASSEMBLY |
![]() |
Install the steering column assembly onto the instrument panel reinforcement assembly with the bolt and 2 nuts.
Connect all the connectors and clamp the wire harnesses onto the steering post assembly bracket.
| 12. INSTALL BRAKE PEDAL SUPPORT SUB-ASSEMBLY (for Manual Transaxle) |
![]() |
Install the pedal support with the bolt and 4 nuts.
| 13. INSTALL BRAKE MASTER CYLINDER PUSH ROD CLEVIS (for Manual Transaxle) |
Apply lithium soap base glycol grease to the push rod pin.
![]() |
Install the push rod clevis with the push rod pin and clip.
Install the brake pedal return spring.
| 14. INSTALL BRAKE PEDAL (for Automatic Transaxle) |
Apply MP grease No. 2 to the brake master cylinder push rod clevis pin and installation surfaces.
Install the 2 brake pedal bushes, and install the brake pedal with the nut and brake pedal shaft.
![]() |
Apply MP grease No. 2 to the brake master cylinder push rod clevis pin and installation surfaces.
Connect the brake master cylinder push rod clevis to the brake pedal with the brake master cylinder push rod clevis pin, install the clip onto the brake master cylinder push rod clevis pin, and then install the brake pedal return spring.
| 15. INSTALL STEERING SLIDING YOKE SUB-ASSEMBLY |
![]() |
Align the matchmarks and install the sliding yoke onto the power steering assembly with bolt B.
Tighten bolt A.
| 16. INSTALL COLUMN HOLE COVER SILENCER SHEET |
![]() |
Install the column hole cover plate with the 2 clips.
Install the floor carpet.
| 17. CONNECT POWER STEERING ECU |
![]() |
Connect the 2 steering post assembly connectors to the power steering ECU.
Install the power steering motor harness and torque sensor wire harness clamps onto the side of the power steering ECU.
Tilt the steering post assembly up and down to make sure that the power steering motor harness and torque sensor wire harness do not interfere with any components.
| 18. INSTALL COMBINATION SWITCH ASSEMBLY |
![]() |
Install the turn signal switch assembly with spiral cable onto the steering post assembly with the clamp.
Connect all the connectors to the turn signal switch with spiral cable.
| 19. INSTALL STEERING COLUMN COVER |
![]() |
Engage the claw to install the steering column upper cover.
![]() |
Engage the 2 claws to install the steering column lower cover.
Install the 3 screws.
| 20. INSTALL STEERING WHEEL ASSEMBLY |
![]() |
Align the matchmarks and install the steering wheel assembly onto the steering column assembly.
Install the nut.
Connect all connectors to the spiral cable.
| 21. INSTALL STEERING PAD |
![]() |
Confirm that the ignition switch is turned to OFF.
Confirm that the negative battery terminal is detached.
Connect the horn terminal.
Connect the airbag connector.
![]() |
Install the steering pad.
Using "TORX" socket wrench T30, tighten the 2 bolts.
| 22. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY |
![]() |
Using a nipper, cut off both ends of the runner portion shown in the illustration (When installing a new one).
Install the lower instrument panel with the 6 <D> bolts, 2 <E> bolts, screw <G> and screw <H>.
Connect the clamps and connectors.

![]() |
Engage the 2 claws and connect the DLC3 connector.
| 23. CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY |
![]() |
Engage the 3 claws to connect the control lever.
| 24. CONNECT ANTENNA CORD SUB-ASSEMBLY |
![]() |
for LHD:
Connect the 5 antenna cord clamps.
![]() |
for RHD:
Connect the 4 antenna cord clamps.
| 25. INSTALL INSTRUMENT PANEL BOX |
![]() |
Insert the stopper of the instrument panel box from the cutout of the instrument panel lower.
![]() |
Engage the 2 hinges with the instrument panel open.
Close the instrument panel box.
| 26. INSTALL INSTRUMENT PANEL UNDER TRAY |
![]() |
Engage the 6 claws and install the instrument panel under tray.
Install the 2 <A> screws.
![]() |
Engage the 4 claws and install the instrument panel under tray.
| 27. INSTALL INSTRUMENT PAD LOWER RH |
![]() |
Engage the claw and 3 clips and install the instrument pad lower.
Install screw <I>.
| 28. INSTALL INSTRUMENT PAD LOWER LH |
![]() |
Engage the claw and 3 clips and install the instrument pad lower.
Install screw <I>.
| 29. INSTALL REAR CONSOLE BOX ASSEMBLY |
![]() |
Engage the 4 claws and install the rear console box.
Install the 2 bolts and 2 screws.
Connect the clamp.
| 30. INSTALL CONSOLE BOX CARPET |
![]() |
Install the console box carpet.
| 31. INSTALL CONSOLE UPPER REAR PANEL SUB-ASSEMBLY |
![]() |
Connect the connector.
Engage the 3 clips and 3 claws and install the console upper rear panel.
| 32. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY |
![]() |
Engage the 5 clips and the claw and install the upper console panel.
| 33. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transaxle) |
![]() |
Install the shift lever knob.
| 34. INSTALL COWL SIDE TRIM BOARD RH |
![]() |
Engage the stud bolt and the claw and install the cowl side trim board.
| 35. INSTALL COWL SIDE TRIM BOARD LH |
| 36. INSTALL FRONT DOOR SCUFF PLATE RH |
![]() |
Engage the 11 claws and install the front door scuff plate.
| 37. INSTALL FRONT DOOR SCUFF PLATE LH |
| 38. INSTALL UPPER INSTRUMENT PANEL SUB-ASSEMBLY |
![]() |
Using a nipper, cut off both ends of the runner portion shown in the illustration (When installing a new one).
Engage the 5 claws at the front side of the instrument panel.
Engage the 7 clips at the rear side of the instrument panel.

Install the upper instrument panel with the 2 <C> bolts and the 2 <B> screws.

![]() |
Connect the passenger airbag connector and clamp.
| 39. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY |
![]() |
Engage the claws of the hinge portions by pushing the glove compartment door in the horizontal direction to install the glove compartment door assembly.
![]() |
Slightly flex the upper portion of the glove compartment door assembly to engage the stopper.
Install the glove compartment door stopper onto the glove compartment door.
| 40. INSTALL FRONT PILLAR GARNISH RH |
![]() |
w/ Curtain Shield Airbag:
Remove the piece of cloth or nylon.
![]() |
Install the 3 clamps.
Connect the antenna connector.
![]() |
w/ Curtain Shield Airbag:
Install a new special clip and the clip onto the front pillar garnish.
Engage the 2 clips and the 2 claws and install the front pillar garnish.
![]() |
w/o Curtain Shield Airbag:
Engage the 2 clips and the 2 claws and install the front pillar garnish.
| 41. INSTALL FRONT PILLAR GARNISH LH |
![]() |
w/ Curtain Shield Airbag:
Remove the piece of cloth or nylon.
![]() |
Install the 4 clamps.
![]() |
w/ Curtain Shield Airbag:
Install a new special clip and the clip onto the front pillar garnish.
Engage the 2 clips and the 2 claws and install the front pillar garnish.
![]() |
w/o Curtain Shield Airbag:
Engage the 2 clips and the 2 claws and install the front pillar garnish.
| 42. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH |
Install the front door opening trim weatherstrip.
| 43. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH |
Install the front door opening trim weatherstrip.
| 44. CONNECT AIR INLET DAMPER CONTROL CABLE SUB-ASSEMBLY |
![]() |
Engage the 2 claws and connect the air inlet damper control cable.
| 45. CONNECT DEFROSTER DAMPER CONTROL CABLE SUB-ASSEMBLY |
![]() |
Engage the 2 claws and connect the defroster damper control cable.
| 46. CONNECT AIR MIX DAMPER CONTROL CABLE SUB-ASSEMBLY |
![]() |
Engage the 2 claws and connect the air mix control cable clamp.
Connect the air mix damper control cable to the clamp.
| 47. INSTALL AIR CONDITIONING PANEL ASSEMBLY |
![]() |
Connect the 3 connectors and the 4 clamps.
![]() |
Engage the 4 clips and 2 claws and install the air conditioning panel.
| 48. INSTALL STEREO OPENING COVER (w/o Radio Receiver) |
![]() |
Install the stereo opening cover with the 4 screws.
| 49. INSTALL RADIO RECEIVER ASSEMBLY |
![]() |
Connect the plug.
Connect the 2 radio connectors.
![]() |
Align the 2 bosses of the instrument panel with the hole in the radio bracket.
Install the radio receiver with the 4 bolts.
| 50. INSTALL INSTRUMENT CLUSTER FINISH PANEL CENTER SUB-ASSEMBLY |
![]() |
Engage the 2 claws and 4 clips and install the instrument cluster finish panel center.
| 51. INSTALL COMBINATION METER ASSEMBLY |
![]() |
Install the combination meter assembly with the 2 screws.
Connect the 2 connectors.
| 52. INSTALL INSTRUMENT CLUSTER FINISH PANEL NO.1 |
![]() |
Fit the 2 claws of the instrument cluster finish panel into the upper instrument cluster finish panel center.
![]() |
Engage the 5 claws and 5 clips and install the instrument cluster finish panel.
| 53. INSTALL INSTRUMENT PANEL FINISH PANEL END RH |
![]() |
Engage the 6 claws and 3 clips and install the instrument panel finish panel end RH.
| 54. INSTALL INSTRUMENT PANEL FINISH PANEL END LH |
![]() |
Engage the 6 claws and 3 clips and install the instrument panel finish panel end LH.
| 55. INSTALL INSTRUMENT PANEL FINISH PANEL LOWER CENTER |
![]() |
Engage the 2 claws and 2 clips and install the instrument panel finish panel lower center.
| 56. CONNECT HEATER WATER INLET HOSE |
![]() |
Install the heater water inlet hose onto the heater unit.
| 57. CONNECT HEATER WATER OUTLET HOSE |
![]() |
Install the heater water outlet hose onto the heater unit.
| 58. INSTALL LIQUID TUBE SUB-ASSEMBLY |
Remove the vinyl tape from the liquid tube and the connecting portion of the unit.
Apply sufficient compressor oil (ND-OIL8) to a new O-ring and the connecting part of the liquid tube.
Install the O-ring onto the liquid tube.
Connect the liquid tube to the unit.
| 59. INSTALL SUCTION TUBE SUB-ASSEMBLY |
Remove the vinyl tape from the suction tube and the connecting part of the unit.
Apply sufficient compressor oil (ND-OIL8) to a new O-ring and the connecting part of the suction tube.
Install the O-ring onto the suction tube.
![]() |
Insert the tube joints securely into the fitting holes and tighten the bolt.
| 60. ADD ENGINE COOLANT (for 1NZ-FE) |
Tighten all the plugs.
Pour engine coolant into the radiator assembly until it overflows.
Check the engine coolant level inside the radiator assembly by squeezing the inlet and outlet radiator hoses several times by hand. If the engine coolant level goes down, add engine coolant.
Install the radiator cap sub-assembly securely.
Slowly pour engine coolant into the radiator reservoir until it reaches the FULL line.
Warm up the engine until the cooling fan operates.
Set the air conditioning as follows while warming up the engine.
| Item | Manual air conditioning system | Automatic air conditioning system |
| Set control as follows | Fan speed - Any setting except "OFF" Temperature - Toward WARM Air conditioning switch "OFF" | Fan speed - Any setting except "OFF" Temperature - To the highest temperature Air conditioning switch "OFF" "AUTO" switch "OFF" |
Maintain the engine speed at 2,000 to 2,500 rpm and warm up the engine until the cooling fan operates.
Stop the engine and wait until the coolant cools down.
If the engine coolant level is below the full level, perform steps (b) through (g) again and repeat the operation until the engine coolant level stays at the full level.
Recheck the engine coolant level inside the radiator reservoir tank assembly. If it is below the full level, add the engine coolant.
Visually check for engine coolant leakage.
| 61. ADD ENGINE COOLANT (for 2NZ-FE) |
Tighten all the plugs.
Pour engine coolant into the radiator assembly until it overflows.
Check the engine coolant level inside the radiator assembly by squeezing the inlet and outlet radiator hoses several times by hand. If the engine coolant level goes down, add engine coolant.
Install the radiator cap sub-assembly securely.
Slowly pour engine coolant into the radiator reservoir until it reaches the FULL line.
Warm up the engine until the cooling fan operates.
Set the air conditioning as follows while warming up the engine.
| Item | Manual air conditioning system | Automatic air conditioning system |
| Set control as follows | Fan speed - Any setting except "OFF" Temperature - Toward WARM Air conditioning switch "OFF" | Fan speed - Any setting except "OFF" Temperature - To the highest temperature Air conditioning switch "OFF" "AUTO" switch "OFF" |
Maintain the engine speed at 2,000 to 2,500 rpm and warm up the engine until the cooling fan operates.
Stop the engine and wait until the coolant cools down.
If the engine coolant level is below the full level, perform steps (b) through (g) again and repeat the operation until the engine coolant level stays at the full level.
Recheck the engine coolant level inside the radiator reservoir tank assembly. If it is below the full level, add the engine coolant.
| 62. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 63. CHECK SRS WARNING LIGHT |
| 64. CHARGE REFRIGERANT |

Perform vacuum purging using a vacuum pump.
Charge refrigerant HFC-134a (R134a).

Install the caps onto the service valves on the refrigerant line.
| 65. WARM UP ENGINE |
| 66. CHECK FOR ENGINE COOLANT LEAK (for 1NZ-FE) |
![]() |
Fill the radiator assembly with engine coolant, then attach a radiator cap tester.
Pump the tester to 137 kPa (1.4 kgf/cm2, 19.9 psi), then check that the pressure does not drop.
If the pressure drops, check the hoses, radiator assembly and water pump assembly for leakage. If there are no signs or traces of external engine coolant leakage, check the heater core, cylinder block and head.
| 67. CHECK FOR ENGINE COOLANT LEAK (for 2NZ-FE) |
![]() |
Fill the radiator assembly with engine coolant, then attach a radiator cap tester.
Pump the tester to 137 kPa (1.4 kgf/cm2, 19.9 psi), then check that the pressure does not drop.
If the pressure drops, check the hoses, radiator assembly and water pump assembly for leakage. If there are no signs or traces of external engine coolant leakage, check the heater core, cylinder block and head.
| 68. CHECK FOR REFRIGERANT LEAK |
After recharging the refrigerant gas, check for refrigerant gas leakage using a halogen leak detector.
Perform the operation as follows:
![]() |
Using the halogen leak detector, check the refrigerant line, especially at the connection points, for leakage.
![]() |
Bring the halogen leak detector close to the drain hose before performing the test.
If no gas leakage is detected from the drain hose, remove the blower motor from the cooling unit. Insert the halogen leak detector sensor into the unit and perform the test.
Disconnect the pressure switch connector and leave it for approximately 20 minutes. Bring the halogen leak detector close to the pressure switch and perform the test.
| 69. POSITION FRONT WHEELS FACING STRAIGHT AHEAD |
| 70. PERFORM CALIBRATION OF TORQUE SENSOR ZERO POINT |