Home › HEATER & AIR CONDITIONING SYSTEM › AIR CONDITIONING › AIR CONDITIONING UNIT (for Sedan)

AIR CONDITIONING UNIT (for Sedan) > REMOVAL

for Preparation Click here



1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).



2. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM
  1. Start up the engine.

  1. Switch A/C ON.

  1. Turn the blower switch to ON.

  1. Operate the cooler compressor with an engine speed of approximately 1,000 rpm for 5 to 6 minutes to circulate the refrigerant and collect the remaining compressor oil from each component, in the cooler compressor.

  1. Stop the engine.



    I101550E01
  1. Remove the caps from the service valves on the refrigerant line.

  1. Connect the Freon collection/recycling device to discharge the refrigerant gas remaining in the refrigeration system.

    NOTICE:
    Use the Freon collection/recycling device in accordance with the manufacturer's instruction manual.



3. DRAIN ENGINE COOLANT (for 1NZ-FE)

NOTICE:
To avoid the danger of being burned, do not remove the radiator cap sub-assembly while the engine and radiator assembly are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator assembly.

  1. Loosen the radiator drain cock plug.

  1. Remove the radiator cap sub-assembly.



  1. Loosen the cylinder block drain cock plug, then drain the coolant.


    A106596E01



4. DRAIN ENGINE COOLANT (for 2NZ-FE)

NOTICE:
To avoid the danger of being burned, do not remove the radiator cap sub-assembly while the engine and radiator assembly are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator assembly.

  1. Loosen the radiator drain cock plug.

  1. Remove the radiator cap sub-assembly.



  1. Loosen the cylinder block drain cock plug, then drain the coolant.


    A106596E01



5. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait for at least 90 seconds after disconnecting the cable to prevent the airbag from working.



6. DISCONNECT SUCTION TUBE SUB-ASSEMBLY


I101236
  1. Remove the bolt.

  1. Turn the hook connector clockwise and disconnect the suction tube.

  1. Remove the O-ring from the suction tube.

    NOTICE:
    Seal the openings of the disconnected parts using vinyl tape to prevent the entry of moisture and foreign matter.



7. DISCONNECT LIQUID TUBE SUB-ASSEMBLY
  1. Disconnect the liquid tube.

  1. Remove the O-ring from the liquid tube.

    NOTICE:
    Seal the openings of the disconnected parts with vinyl tape to prevent the entry of moisture and foreign matter.



8. DISCONNECT HEATER WATER OUTLET HOSE


I101170
  1. Using pliers, grip the claws of the clip, slide the clip and disconnect the heater water outlet hose from the heater unit.



9. DISCONNECT HEATER WATER INLET HOSE


I101171
  1. Using pliers, grip the claws of the clip, slide the clip and disconnect the heater water inlet hose from the heater unit.



10. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY
(Click here)


11. REMOVE STEERING COLUMN ASSEMBLY
(Click here)


12. REMOVE HEATER TO REGISTER DUCT ASSEMBLY


I102581
  1. Disengage the 3 claws and remove the heater to register duct.



13. REMOVE DEFROSTER NOZZLE ASSEMBLY


I104062
  1. Disconnect the connector and 3 clamps.

  1. Disengage the 5 claws and remove the defroster nozzle.



14. REMOVE INSTRUMENT PANEL BRACE SUB-ASSEMBLY (for LHD)


I106099
  1. Disengage the clamp.

  1. Remove the bolt, screw and nut and remove the instrument panel brace.



15. REMOVE INSTRUMENT PANEL BRACE SUB-ASSEMBLY (for RHD)


I103548
  1. Disengage the 3 clamps.

  1. Remove the bolt, screw and nut and remove the instrument panel brace.



16. SEPARATE MAIN BODY ECU (for LHD)


I103999
  1. Disconnect the 5 connectors and the 3 clamps.



    I101239
  1. Remove the 2 bolts and separate the main body ECU.



17. SEPARATE MAIN BODY ECU (for RHD)


I103549
  1. Disconnect the 5 connectors and the 5 clamps.



    I103550
  1. Remove the 2 bolts.

  1. Disengage the clamp and separate the main body ECU.



18. SEPARATE CONNECTOR NO. 2 HOLDER


I102585
  1. Remove the bolt.



    I102615
  1. Disconnect the connectors and separate the connector No. 2 holder.



19. REMOVE INSTRUMENT PANEL REINFORCEMENT


I101178
  1. Disconnect the drain hose.



    I102586
  1. Remove the bolt and disconnect the ground wire.

  1. Disconnect the connectors.



  1. Disengage the clamps (for LHD).


    I103990



  1. Disengage the clamps (for RHD).


    I103552



  1. Disconnect the connectors and clamps (for LHD).


    I104061



  1. Disconnect the connectors and clamps (for RHD).


    I103782



  1. Remove the 3 bolts and the nut.


    I102591



  1. Remove the 9 bolts and remove the instrument panel reinforcement with air conditioning unit.


    I102593



    I102594
  1. Remove the 3 screws and the air conditioning unit.



20. REMOVE AIR CONDITIONING AMPLIFIER ASSEMBLY


I101549
  1. Remove the screw and the air conditioning amplifier.



21. REMOVE AIR CONDITIONING UNIT


I102598
  1. Remove the 3 screws and the air conditioning unit.