Home › BODY › INSTRUMENT PANEL › LOWER INSTRUMENT PANEL (for Sedan)

LOWER INSTRUMENT PANEL (for Sedan) > REMOVAL

for Preparation Click here


HINT:
Use the same procedure for both the RH and LH sides.



1. BOLTS, SCREWS AND NUTS TABLE


HINT:
All bolts, screws and nuts relevant to installing and removing the instrument panel are shown, along with their alphabetic codes, in the table below.



B132394E01



2. REMOVE INSTRUMENT PANEL CUP HOLDER RH


    B176550E02
  1. Apply protective tape, as shown in the illustration.
    Text in Illustration 
    *1
    Stopper
    *2
    Protective Tape

  1. Open the instrument panel cup holder.

  1. Flex both sides of the instrument panel cup holder and disengage the 2 stoppers.



    B132399
  1. Disengage the spring.



    B176551
  1. Remove the instrument panel cup holder by moving it toward either the inside or the outside of the vehicle and disengaging the 2 hinges one at a time.



3. REMOVE INSTRUMENT PANEL CUP HOLDER SPRING RH


B132402
  1. Remove the spring.



4. REMOVE INSTRUMENT PANEL CUP HOLDER LH


    B176552E02
  1. Apply protective tape, as shown in the illustration.
    Text in Illustration 
    *1
    Stopper
    *2
    Protective Tape

  1. Open the instrument panel cup holder.

  1. Flex both sides of the instrument panel cup holder and disengage the 2 stoppers.



    B176553
  1. Remove the instrument panel cup holder by moving it toward either the inside or the outside of the vehicle and disengaging the 2 hinges one at a time.



5. REMOVE INSTRUMENT PANEL CUP HOLDER SPRING LH


B132406
  1. Remove the spring.



6. REMOVE UPPER INSTRUMENT PANEL SUB-ASSEMBLY
(Click here)


7. REMOVE INSTRUMENT CLUSTER FINISH PANEL CENTER SUB-ASSEMBLY (except Integrated with Panel)


B132395
  1. Disengage the 2 claws and 4 clips and remove the instrument cluster panel center.



8. REMOVE STEREO OPENING COVER (w/o Radio Receiver)


B132396
  1. Remove the 4 screws and remove the stereo opening cover.



9. REMOVE RADIO RECEIVER ASSEMBLY (except Integrated with Panel)


    B138302
  1. Remove the 4 bolts and the radio receiver.



    B138304
  1. Disconnect the plug.

  1. Disconnect the 2 radio connectors.



10. REMOVE RADIO RECEIVER ASSEMBLY (for Integrated with Panel)


    B138579
  1. Disconnect the hazard warning signal switch connector.

  1. Remove the 4 bolts.



    B138580
  1. Disengage the 4 clips and the 4 claws and remove the radio receiver.



    B138582
  1. Disconnect the plug.

  1. Disconnect the 3 radio connectors.



11. REMOVE AIR CONDITIONING PANEL ASSEMBLY


I102566
  1. Disengage the 4 clips and 2 claws and remove the air conditioning panel.



    I104067
  1. Disconnect the 3 connectors and 4 clamps.



12. DISCONNECT AIR MIX DAMPER CONTROL CABLE SUB-ASSEMBLY


I102568
  1. Disconnect the air mix damper control cable from the clamp.

  1. Disengage the 2 claws and disconnect the air mix damper control cable.



13. DISCONNECT DEFROSTER DAMPER CONTROL CABLE SUB-ASSEMBLY


I102569
  1. Disengage the 2 claws and disconnect the defroster damper control cable.



14. DISCONNECT AIR INLET DAMPER CONTROL CABLE SUB-ASSEMBLY


I102570
  1. Disengage the 2 claws and disconnect the air inlet damper control cable.



15. REMOVE FRONT DOOR SCUFF PLATE RH


    B134764
  1. Disengage the 11 claws and remove the front door scuff plate.



16. REMOVE FRONT DOOR SCUFF PLATE LH

HINT:
Use the same procedure as for the RH side.



17. REMOVE COWL SIDE TRIM BOARD RH


    B114285
  1. Disengage the claw and the stud bolt and remove the cowl side trim board.



18. REMOVE COWL SIDE TRIM BOARD LH

HINT:
Use the same procedure as for the RH side.



19. REMOVE REAR CONSOLE BOX ASSEMBLY
(Click here)


20. REMOVE INSTRUMENT PAD LOWER LH


B132339
  1. Remove screw <I>.

  1. Disengage the claw and 3 clips and remove the instrument panel pad lower.



21. REMOVE INSTRUMENT PAD LOWER RH


B132340
  1. Remove screw <I>.

  1. Disengage the claw and 3 clips and remove the instrument panel pad lower.



22. REMOVE INSTRUMENT PANEL UNDER TRAY


B132341
  1. Disengage the 4 claws and open the instrument panel under tray.



    B132333
  1. Remove the 2 <A> screws.

  1. Disengage the 6 claws and remove the instrument panel under tray.



23. REMOVE INSTRUMENT PANEL BOX


B176558
  1. Open the instrument panel box.

  1. Pull the instrument panel box out horizontally with the instrument panel open and disengage the 2 hinges.



    B132335E02
  1. Remove the stopper of the instrument panel box from the cutout of the instrument panel lower and remove the instrument panel box.
    Text in Illustration 
    *1
    Stopper
    *a
    Cutout



24. DISCONNECT ANTENNA CORD SUB-ASSEMBLY


    B176560
  1. for LHD:

    1. Disconnect the 5 antenna cord clamps.



    B168987
  1. for RHD:

    1. Disconnect the 4 antenna cord clamps.



25. SEPARATE HOOD LOCK CONTROL LEVER SUB-ASSEMBLY


B132338
  1. Disengage the 3 claws and separate the hood lock control lever.



26. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY


B108192
  1. Disengage the 2 claws and disconnect the DLC3 connector.

  1. Disconnect the clamps and connectors.



  1. Remove the 6 <D> bolts, 2 <E> bolts, screw <G> and screw <H> and remove the lower instrument panel.


    B132342E01



27. REMOVE INSTRUMENT PANEL CUP HOLDER SUB-ASSEMBLY LH


B132343
  1. Remove the 3 <A> screws and the instrument panel cup holder.



28. REMOVE INSTRUMENT PANEL CUP HOLDER SUB-ASSEMBLY RH


B132344
  1. Remove the 3 <A> screws and the instrument panel box.



29. REMOVE GLOVE COMPARTMENT DOOR STOPPER SUB-ASSEMBLY


B132392
  1. Disengage the claw and remove the glove compartment door stopper.



30. REMOVE OUTER MIRROR SWITCH ASSEMBLY


B132357
  1. Disengage the 2 claws and remove the outer mirror switch.



31. REMOVE HEADLIGHT LEVELING SWITCH


B132359
  1. Disengage the 2 claws and remove the headlight leveling switch.



32. REMOVE STEREO JACK ADAPTER ASSEMBLY


B132360
  1. Disengage the 2 claws and remove the stereo jack adapter.



33. REMOVE INSTRUMENT PANEL HOLE COVER


B130144
  1. Remove the 2 <H> screws and the instrument hole cover.



34. REMOVE INSTRUMENT CLUSTER FINISH PANEL SEAL


B132393
  1. Disengage the 5 claws and remove the panel seal.



35. REMOVE INSTRUMENT PANEL NO. 1 SAFETY PAD


B132362
  1. Remove the safety pad.



36. REMOVE INSTRUMENT PANEL NO. 2 SAFETY PAD


B132361
  1. Remove the safety pad.