DTC P0351 Ignition Coil "A" Primary / Secondary Circuit |
DTC P0352 Ignition Coil "B" Primary / Secondary Circuit |
DTC P0353 Ignition Coil "C" Primary / Secondary Circuit |
DTC P0354 Ignition Coil "D" Primary / Secondary Circuit |

| DTC No. | DTC Detection Conditions | Trouble Areas |
| P0351 P0352 P0353 P0354 | No IGF signal to ECM while engine running (1 trip detection logic) |
|

| Items | Contents |
| Terminals | CH1: IGT1, IGT2, IGT3, IGT4 - E1 CH2: IGF1 - E1 |
| Equipment Settings | 2 V/Division, 20 msec./Division |
| Conditions | Cranking or idling |

| 1.INSPECT IGNITION COIL ASSEMBLY (POWER SOURCE) |
![]() |
Disconnect the C11, C12, C13 or C14 ignition coil with igniter connector.
Check the resistance.
| Tester Connections | Specified Conditions |
| GND (C11-4) - Body ground | Below 1 Ω |
| GND (C12-4) - Body ground | |
| GND (C13-4) - Body ground | |
| GND (C14-4) - Body ground |
Turn the ignition switch to ON.
Measure the voltage between the terminals of the wire harness side connector.
| Tester Connections | Specified Conditions |
| +B (C11-1) - GND (C11-4) | 9 to 14 V |
| +B (C12-1) - GND (C12-4) | |
| +B (C13-1) - GND (C13-4) | |
| +B (C14-1) - GND (C14-4) |
Reconnect the ignition coil with igniter connector.
|
| ||||
| OK | |
| 2.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM) |
![]() |
Disconnect the C11, C12, C13 or C14 ignition coil with igniter connector.
Disconnect the C20 ECM connector.
Check the resistance.
| Tester Connections | Specified Conditions |
| IGF (C11-2) - IGF1 (C20-81) | Below 1 Ω |
| IGF (C12-2) - IGF1 (C20-81) | |
| IGF (C13-2) - IGF1 (C20-81) | |
| IGF (C14-2) - IGF1 (C20-81) |
| Tester Connections | Specified Conditions |
| IGT1 (C11-3) - IGT1 (C20-85) | Below 1 Ω |
| IGT2 (C12-3) - IGT2 (C20-84) | |
| IGT3 (C13-3) - IGT3 (C20-83) | |
| IGT4 (C14-3) - IGT4 (C20-82) |
| Tester Connections | Specified Conditions |
| IGF (C11-2) or IGF1 (C20-81) - Body ground | 10 kΩ or higher |
| IGF (C12-2) or IGF1 (C20-81) - Body ground | |
| IGF (C13-2) or IGF1 (C20-81) - Body ground | |
| IGF (C14-2) or IGF1 (C20-81) - Body ground |
| Tester Connections | Specified Conditions |
| IGT1 (C11-3) or IGT1 (C20-85) - Body ground | 10 kΩ or higher |
| IGT2 (C12-3) or IGT2 (C20-84) - Body ground | |
| IGT3 (C13-3) or IGT3 (C20-83) - Body ground | |
| IGT4 (C14-3) or IGT4 (C20-82) - Body ground |
Reconnect the ECM connector.
Reconnect the ignition coil with igniter connector.
|
| ||||
| OK | |
| 3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0351, P0352, P0353 OR P0354) |
Connect an intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Clear DTCs (Click here).
Shuffle arrangement of the ignition coils with igniters (among No. 1 to No. 4 cylinders).
Perform a simulation test.
Check DTCs displayed on the tester.
| Display (DTC Output) | Proceed To |
| Same DTC output | A |
| Different ignition coil DTC output | B |
|
| ||||
| A | ||
| ||