DTC C1405 Open or Short in Front Speed Sensor RH Circuit |
DTC C1406 Open or Short in Front Speed Sensor LH Circuit |
| DTC NO. | DTC Detection Condition | Trouble Area |
| C1405 C1406 | Either of the following is detected:
|
|

| 1.READ VALUE USING INTELLIGENT TESTER (MOMENTARY INTERRUPTION) |
Using the intelligent tester, check for any momentary interruption in the wire harness and connector corresponding to the DTC (Click here).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| FR Speed Open | FR speed sensor open detection / Error or Normal | Error: Momentary interruption Normal: Normal | - |
| FL Speed Open | FL speed sensor open detection / Error or Normal | Error: Momentary interruption Normal: Normal | - |
|
| ||||
| OK | |
| 2.READ VALUE USING INTELLIGENT TESTER (FRONT SPEED SENSOR) |
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| FR Wheel Speed | FR wheel speed sensor reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h | When driving at constant speed: No large fluctuations |
| FL Wheel Speed | FL wheel speed sensor reading /min.: 0 km/h (0 mph), max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h | When driving at constant speed: No large fluctuations |
Check that there is no difference between the speed value output from the speed sensor displayed on the intelligent tester and the speed value displayed on the speedometer when driving the vehicle.
|
| ||||
| OK | |
| 3.RECONFIRM DTC |
Turn the ignition switch off.
Clear the DTCs (Click here).
Start the engine.
Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.
Check if the same DTC is recorded (Click here).
| Result | Proceed to |
| DTCs (C1405 and C1406) are not output | A |
| DTCs (C1405 and/or C1406) are output | B |
|
| ||||
| A | ||
| ||
| 4.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - FRONT SPEED SENSOR) |
Turn the ignition switch off.
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
Disconnect the A76 brake actuator assembly (skid control ECU) connector and the A74 and/or A75 front speed sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A76-7 (FR+) - A74-2 (FR+) | Always | Below 1 Ω |
| A76-6 (FR-) - A74-1 (FR-) | Always | Below 1 Ω |
| A76-19 (FL+) - A75-2 (FL+) | Always | Below 1 Ω |
| A76-18 (FL-) - A75-1 (FL-) | Always | Below 1 Ω |
| A76-7 (FR+) - Body ground | Always | 10 kΩ or higher |
| A76-6 (FR-) - Body ground | Always | 10 kΩ or higher |
| A76-19 (FL+) - Body ground | Always | 10 kΩ or higher |
| A76-18 (FL-) - Body ground | Always | 10 kΩ or higher |
Reconnect the A76 brake actuator assembly (skid control ECU) connector and the front speed sensor connector.
|
| ||||
| OK | |
| 5.CHECK BRAKE ACTUATOR ASSEMBLY (SENSOR INPUT) |
![]() |
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A74-2 (FR+) - Body ground | Ignition switch ON | 8 to 14 V |
| Tester Connection | Switch Condition | Specified Condition |
| A75-2 (FL+) - Body ground | Ignition switch ON | 8 to 14 V |
| *a | Front view of wire harness connector (to Front Speed Sensor) |
| *b | RH |
| *c | LH |
|
| ||||
| OK | ||
| ||