RADIO ANTENNA CORD (for Hatchback 3 Door) > INSTALLATION |
| 1. INSTALL ANTENNA CORD SUB-ASSEMBLY |
w/ Curtain Shield Airbag:
Align the red locating tape on the antenna cord with claw A on the side rail spacer and install the cord into the claw.
Install the antenna cord into the 2 claws on the side rail spacer.
Insert the antenna cord into the cutout of the roof headlining.
Align the locating tapes on the antenna cord with the markings on the roof headlining.
Install the antenna cord onto the roof headlining with 6 new pieces of tape.

| Mark | Measurement |
| a | 80 mm (3.15 in.) |
| b | 20 mm (0.787 in.) |
w/o Curtain Shield Airbag:
Align the red locating tape on the antenna cord with claw A on the side rail spacer and install the cord into the claw.
Install the antenna cord into the 4 claws on the side rail spacer.
Insert the antenna cord into the cutout of the roof headlining.
Align the locating tapes on the antenna cord with the markings on the roof headlining.
Install the antenna cord onto the roof headlining with 4 new pieces of tape.

| Mark | Measurement |
| a | 80 mm (3.15 in.) |
| b | 20 mm (0.787 in.) |
| 2. INSTALL ROOF HEADLINING ASSEMBLY |
![]() |
Pull the roof headlining back into the vehicle through the back door.
w/ Curtain Shield Airbag:
for 3 Point Type Rear Center Seat Belt:
for 2 Point Type Rear Center Seat Belt:

w/o Curtain Shield Airbag:
for 3 Point Type Rear Center Seat Belt:
for 2 Point Type Rear Center Seat Belt:

![]() |
Install the 2 connectors.
Connect the 2 connectors.
Install the antenna cord onto the antenna cord clamp.
![]() |
for LHD:
Connect the connector.
Install the wiring harness clamp.
![]() |
for RHD:
Connect the connector.
Install the No. 1 roof wire into the claw of the junction block.
![]() |
Install the wiring harness clamp.
| 3. INSTALL INSTRUMENT PANEL BOX (for LHD) |
![]() |
Insert the stopper of the instrument panel box from the cutout of the instrument panel lower.
Engage the 2 hinges with the instrument panel open.
Close the instrument panel box.
| 4. INSTALL NO. 2 ANTENNA CORD SUB-ASSEMBLY |
for LHD:
Engage the 4 clamps.
Install the bolt.
Connect the 2 connectors and install the No. 2 antenna cord.

for RHD:
Engage the 5 clamps.
Install the bolt.
Connect the 2 connectors and install the No. 2 antenna cord.

| 5. INSTALL UPPER INSTRUMENT PANEL SUB-ASSEMBLY |
![]() |
Using a nipper, cut off both ends of the runner portion shown in the illustration (When installing a new one).
Engage the 5 claws at the upper side of the instrument panel.
Engage the claw and the 3 clips at the lower side of the instrument panel.

Install the instrument panel upper with the 2 <C> bolts and the 4 <B> screws.
Connect the connectors.

![]() |
Connect the passenger airbag connector and clamp.
| 6. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY |
![]() |
Engage the claw of the hinge portion in the horizontal direction to install the glove compartment door assembly.
![]() |
Slightly deform the upper portion of the glove compartment door assembly to engage the stopper.
| 7. INSTALL NO. 1 SWITCH HOLE BASE (for LHD) |
![]() |
Disengage the 2 clips and 2 claws and install the switch hole base.
| 8. INSTALL COMBINATION METER ASSEMBLY |
![]() |
Install the combination meter assembly with the 2 screws.
Connect the 2 connectors.
| 9. INSTALL INSTRUMENT CLUSTER FINISH PANEL NO.1 |
![]() |
Fit the 3 A claws of the instrument cluster finish panel into the upper instrument cluster finish panel center.
![]() |
Engage the 4 claws and 5 clips and install the instrument cluster finish panel.
| 10. INSTALL INSTRUMENT PANEL FINISH PANEL END RH |
![]() |
with CD player
Connect the connector.
Engage the 4 claws and 3 clips and install the instrument panel finish panel end RH.
![]() |
Except CD player
Connect the connector.
Engage the 5 claws and 3 clips and install the instrument panel finish panel end RH.
| 11. INSTALL INSTRUMENT PANEL FINISH PANEL END LH |
![]() |
with CD player
Connect the connector.
Engage the 4 claws and 3 clips and install the instrument panel finish panel end LH.
![]() |
Except CD player
Connect the connector.
Engage the 5 claws and 3 clips and install the instrument panel finish panel end LH.
| 12. INSTALL FRONT PILLAR GARNISH RH |
![]() |
w/ Curtain Shield Airbag:
Remove the piece of cloth or nylon.
![]() |
w/ Front No. 2 Speaker:
Insert the hook into the body hole.
Engage the clip and install the front speaker.
![]() |
Connect the speaker connector.
![]() |
Install the 3 antenna cord clamps.
Connect the connector.
w/ Curtain Shield Airbag:
![]() |
Install a new special clip and the clip onto a new front pillar garnish.
Engage the 2 clips and the 2 claws and install the front pillar garnish.
w/o Curtain Shield Airbag:
![]() |
Engage the 2 clips and the 2 claws and install the front pillar garnish.
| 13. INSTALL FRONT PILLAR GARNISH LH |
![]() |
w/ Curtain Shield Airbag:
Remove the piece of cloth or nylon.
![]() |
w/ Front No. 2 Speaker:
Insert the hook into the body hole.
Engage the clip and install the front speaker.
![]() |
Connect the speaker connector.
![]() |
Install the 4 wire harness clamps.
w/ Curtain Shield Airbag:
![]() |
Install a new special clip and the clip onto a new front pillar garnish.
Engage the 2 clips and the 2 claws and install the front pillar garnish.
w/o Curtain Shield Airbag:
![]() |
Engage the 2 clips and the 2 claws and install the front pillar garnish.
| 14. INSTALL MAP LIGHT ASSEMBLY |
![]() |
Connect the map light connector.
![]() |
Engage the 4 claws and install the map light.
| 15. INSTALL ROOM LIGHT ASSEMBLY |
![]() |
Engage the 4 claws and install the room light switch base.
Install the roof wire onto the claw of the room light.
![]() |
Engage the 4 claws and install the room light.
![]() |
Engage the 4 claws and install the 2 covers.
![]() |
Engage the 4 claws and install the room light lens.
| 16. INSTALL VISOR HOLDER RH |
![]() |
Engage the 2 claws by turning the visor holder clockwise between 60 to 120° and install the visor holder.
| 17. INSTALL VISOR HOLDER LH |
| 18. INSTALL VISOR ASSEMBLY RH |
![]() |
Engage the 2 springs and install the visor.
Install the visor shaft into the visor holder.
![]() |
Engage the 4 claws and install the visor bracket cover.
| 19. INSTALL VISOR ASSEMBLY LH |
| 20. INSTALL ASSIST GRIP |
![]() |
Engage the 2 springs and install the assist grip.
| 21. INSTALL COAT HOOK (w/ Coat Hook) |
![]() |
Engage the 2 claws and install the coat hook.
![]() |
Engage the 2 claws and close the cover.
| 22. INSTALL ROOF HEADLINING SERVICE HOLE COVER (w/o Curtain Shield Airbag) |
![]() |
Install the roof headlining service hole cover.
| 23. INSTALL SEAT BELT ANCHOR COVER (for 3 Point Type Rear Center Seat Belt) |
![]() |
Engage the 4 claws and install the seat belt anchor cover.
| 24. INSTALL REAR ROOF SIDE RAIL GARNISH RH |
![]() |
Engage the 4 clips and install the rear roof side rail garnish.
| 25. INSTALL REAR ROOF SIDE RAIL GARNISH LH |
| 26. INSTALL ROOF SIDE INNER GARNISH RH |
![]() |
w/ Curtain Shield Airbag:
for 3 Point Type Rear Center Seat Belt:
for 2 Point Type Rear Center Seat Belt:
![]() |
w/o Curtain Shield Airbag:
for 3 Point Type Rear Center Seat Belt:
for 2 Point Type Rear Center Seat Belt:
| 27. INSTALL ROOF SIDE INNER GARNISH LH |
![]() |
w/ Curtain Shield Airbag:
Install a new special clip onto the roof side inner garnish.
Pass the rear seat outer belt through the slit in the roof side inner garnish.
Engage the 4 clips and the claw and install the roof side inner garnish.
![]() |
w/o Curtain Shield Airbag:
Pass the rear seat outer belt through the slit in the roof side inner garnish.
Engage the 4 clips and the claw and install the roof side inner garnish.
| 28. INSTALL REAR CENTER SEAT OUTER BELT ASSEMBLY (for 3 Point Type Rear Center Seat Belt) |
![]() |
Check the angle of inclination required to lock the retractor.
Gently incline the retractor from its initial position. Check that the belt does not lock when the retractor is inclined 15°or less in any direction. Also, check that the belt locks when the inclination of the retractor is 45°or more.
![]() |
Hook the lower stay of the retractor onto the 2 body hooks and install the retractor with the bolt.
![]() |
Install the bracket with the bolt.
Check that the ELR locks.
With the belt installed, check that the belt locks when it is pulled out quickly.
If the operation is not as specified, replace the rear center seat outer belt.
![]() |
Install the through anchor with the bolt.
![]() |
Engage the 2 claws and close the slip joint cover.
![]() |
Install the 2 tongue plates.
| 29. INSTALL CENTER PILLAR UPPER GARNISH RH |
![]() |
Engage the 2 clips and install the center pillar upper garnish.
| 30. INSTALL CENTER PILLAR UPPER GARNISH LH |
| 31. INSTALL FRONT SEAT OUTER BELT ASSEMBLY RH |
![]() |
Install the through anchor with the bolt.
| 32. INSTALL FRONT SEAT OUTER BELT ASSEMBLY LH |
| 33. INSTALL SEAT BELT ANCHOR COVER CAP |
![]() |
Engage the 3 claws and install the seat belt anchor cover cap.
| 34. INSTALL DECK SIDE TRIM PANEL ASSEMBLY RH |
![]() |
Engage the 3 clips and the 3 claws and install the deck side trim panel.
Tighten the 3 screws.
| 35. INSTALL DECK SIDE TRIM PANEL ASSEMBLY LH |
![]() |
Connect the deck side room light connector.
Engage the 3 clips and the 3 claws and install the deck side trim panel.
Tighten the 3 screws.
| 36. INSTALL REAR SEAT OUTER BELT ASSEMBLY RH |
![]() |
Engage the clip and install the anchor plate.
Tighten the bolt.
| 37. INSTALL REAR SEAT OUTER BELT ASSEMBLY LH |
| 38. INSTALL REAR DECK TRIM COVER |
![]() |
for Grand Tire:
Engage the 8 claws and install the rear deck trim cover.
Install the 2 clips.
![]() |
for Temper Spare Tire:
Engage the 8 claws and install the rear deck trim cover.
Install the 2 clips.
| 39. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY RH |
![]() |
Engage the 8 clips, the retainer and the 10 claws and install the front quarter trim panel.
![]() |
Install the belt of the rear seat outer belt onto the rear seat shoulder belt hanger.
| 40. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY LH |
| 41. INSTALL FRONT SEAT OUTER BELT BAR SUB-ASSEMBLY RH (w/ Seat Belt Bar) |
![]() |
Install the front seat outer belt bar with the 2 bolts.
| 42. INSTALL FRONT SEAT OUTER BELT BAR SUB-ASSEMBLY LH (w/ Seat Belt Bar) |
| 43. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH |
![]() |
Align the location mark with the paint mark first, and install the front door opening trim weatherstrip, as shown in the illustration.
| Area | Color |
| RH side | Yellow |
| LH side | White |
| 44. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH |
| 45. INSTALL COWL SIDE TRIM BOARD RH |
![]() |
Engage the claw and stud bolt and install the cowl side trim board.
| 46. INSTALL COWL SIDE TRIM BOARD LH |
| 47. INSTALL INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY RH |
![]() |
Engage the 4 claws and install the instrument panel under cover.
| 48. INSTALL INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY LH |
![]() |
Engage the 3 claws and install the instrument panel under cover.
Tighten the 2 screws.
| 49. INSTALL FRONT DOOR SCUFF PLATE RH |
![]() |
Engage the 8 claws and install the front door scuff plate.
| 50. INSTALL FRONT DOOR SCUFF PLATE LH |
| 51. INSTALL REAR SEAT ASSEMBLY LH |
![]() |
Insert the 2 location pins through the 2 body holes and install the rear seat.
Using "TORX" socket wrench E10, install the 4 bolts in the sequence shown in the illustration.
![]() |
Install the rear seat cushion.
Using "TORX" socket wrench E10, install the 3 bolts in the sequence shown in the illustration.
| 52. INSTALL REAR SEAT ASSEMBLY RH |
![]() |
Insert the 2 location pins through the 2 body holes and install the rear seat.
Using "TORX" socket wrench E10, install the 4 bolts in the sequence shown in the illustration.
![]() |
Install the rear seat cushion.
Using "TORX" socket wrench E10, install the 2 bolts in the sequence shown in the illustration.
| 53. INSTALL NO. 2 REAR SEAT LEG COVER |
![]() |
Engage the 3 claws and install the No. 2 rear seat leg cover.
| 54. INSTALL NO. 1 REAR SEAT LEG COVER |
for RH Side:
Install the No. 1 rear seat leg cover .
for LH Side:
Install the No. 1 rear seat leg cover .
| 55. INSTALL DECK FLOOR BOX RH (w/ Deck Board) |
![]() |
Set the deck floor box and lock the 2 knobs.
| 56. INSTALL DECK FLOOR BOX LH (w/ Deck Board) |
| 57. INSTALL SPARE WHEEL COVER ASSEMBLY (w/ Deck Board) |
![]() |
Install the spare wheel cover.
| 58. INSTALL DECK BOARD SUB-ASSEMBLY (w/ Deck Board) |
![]() |
Set the deck board and lock the 2 knobs.
| 59. INSTALL REAR FLOOR CARPET ASSEMBLY (w/o Deck Board) |
![]() |
Install the rear floor carpet.
| 60. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Package Tray Trim) |
![]() |
Engage the 2 claws and install the package tray trim panel.
Install the 5 pieces of hook tape.
Install the 2 package tray trim suspenders.
| 61. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 62. CHECK SRS WARNING LIGHT |