Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › CURTAIN SHIELD AIRBAG ASSEMBLY (for Hatchback 5 Door)

CURTAIN SHIELD AIRBAG ASSEMBLY (for Hatchback 5 Door) > INSTALLATION

for Preparation Click here


CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (Click here).

NOTICE:
Always use "TORX" socket wrench E10 when installing the rear seat.

HINT:
The procedure described below is for the RH side. Use the same procedure for both the RH and LH sides, unless otherwise specified.



1. INSTALL ROOF SIDE RAIL BRACKET RH


B108342E01
  1. Insert the 2 hooks into the body holes and install the roof side rail bracket and tighten 1 the bolt.

    Torque:
    9.8 N*m{ 100 kgf*cm , 7 ft.*lbf }

  1. Install the wire harness clamp.



2. INSTALL CURTAIN SHIELD AIRBAG BRACKET RH


B108341E01
  1. Insert the 2 hooks into the body holes and install the curtain shield back bracket and tighten 1 the bolt.

    Torque:
    9.8 N*m{ 100 kgf*cm , 7 ft.*lbf }



3. INSTALL CURTAIN SHIELD AIRBAG ASSEMBLY
  1. Tighten the 2 bolts A.

    Torque:
    14 N*m{ 145 kgf*cm , 10 ft.*lbf }

  1. Tighten the 4 screws B.

  1. Install the front strap.

    NOTICE:
    Attach double sided tape to the indicated area, with the strap pulled downward. When installing the strap, make sure that the front pillar garnish installation holes are not hidden by the strap of the curtain shield airbag.



  1. Tighten the 2 bolts D.

    Torque:
    9.8 N*m{ 100 kgf*cm , 7 ft.*lbf }



    C125681E01



    B108343E01
  1. Connect the airbag connector.

    NOTICE:
    Lock the locking button securely.



4. INSTALL ROOF HEADLINING ASSEMBLY


    B114340
  1. Pull the roof headlining back into the vehicle through the back door.

  1. w/ Curtain Shield Airbag:

    1. for 3 Point Type Rear Center Seat Belt:

      1. Engage the 4 hooks and install the roof headlining.
      2. Install the clip.

    2. for 2 Point Type Rear Center Seat Belt:

      1. Engage the 4 hooks and install the roof headlining.

      2. Install the 2 clips.


        B119910E01

  1. w/o Curtain Shield Airbag:

    1. for 3 Point Type Rear Center Seat Belt:

      1. Engage the 2 claws and the 4 hooks and install the roof headlining.
      2. Install the clip.

    2. for 2 Point Type Rear Center Seat Belt:

      1. Engage the 2 claws and the 4 hooks and install the roof headlining.

      2. Install the 2 clips.


        B119911E01



    B114321
  1. Install the 2 connectors.

  1. Connect the 2 connectors.

  1. Install the antenna cord onto the antenna cord clamp.



    B114511
  1. for LHD:

    1. Connect the connector.

    2. Install the wiring harness clamp.



    B114320
  1. for RHD:

    1. Connect the connector.

    2. Install the No. 1 roof wire into the claw of the junction block.



    3. B114319
    4. Install the wiring harness clamp.



5. INSTALL INSTRUMENT PANEL BOX


B108189E01
  1. Insert the stopper of the instrument panel box from the cutout of the instrument panel lower.

  1. Engage the 2 hinges with the instrument panel open.

  1. Close the instrument panel box.



6. INSTALL INSTRUMENT UPPER PANEL SUB-ASSEMBLY


B108233E01
  1. Using a nipper, cut off both ends of the runner portion shown in the illustration (When installing a new one).

  1. Engage the 5 claws at the upper side of the instrument panel.



  1. Engage the claw and the 3 clips at the lower side of the instrument panel.


    B105355E01

  1. Install the instrument panel upper with the 2 <C> bolts and the 4 <B> screws.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf } for bolt



  1. Connect the connectors.


    B105354E01



    B108182
  1. Connect the passenger airbag connector and clamp.



7. INSTALL NO. 1 SWITCH HOLE BASE


B108201
  1. Disengage the 2 clips and 2 claws and install the switch hole base.



8. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY


B105352
  1. Engage the claw of the hinge portion in the horizontal direction to install the glove compartment door assembly.

    NOTICE:
    Engage the claw in the horizontal direction, otherwise, installation failure caused by excessive play around the hinge portion will result.



    B108202
  1. Slightly deform the upper portion of the glove compartment door assembly to engage the stopper.



9. INSTALL COMBINATION METER ASSEMBLY


E107730
  1. Install the combination meter assembly with the 2 screws.

  1. Connect the 2 connectors.



10. INSTALL INSTRUMENT CLUSTER FINISH PANEL NO.1


B132366E01
  1. Fit the 3 A claws of the instrument cluster finish panel into the upper instrument cluster finish panel center.



    B132367
  1. Engage the 4 claws and 5 clips and install the instrument cluster finish panel.



11. INSTALL INSTRUMENT PANEL FINISH PANEL END RH


E107743
  1. with CD player

    1. Connect the connector.

    2. Engage the 4 claws and 3 clips and install the instrument panel finish panel end RH.



    E107744
  1. Except CD player

    1. Connect the connector.

    2. Engage the 5 claws and 3 clips and install the instrument panel finish panel end RH.



12. INSTALL INSTRUMENT PANEL FINISH PANEL END LH


E107741
  1. with CD player

    1. Connect the connector.

    2. Engage the 4 claws and 3 clips and install the instrument panel finish panel end LH.



    E107742
  1. Except CD player

    1. Connect the connector.

    2. Engage the 5 claws and 3 clips and install the instrument panel finish panel end LH.



13. INSTALL FRONT PILLAR GARNISH RH


    B114342E01
  1. w/ Curtain Shield Airbag:

    1. Remove the piece of cloth or nylon.



    B127672
  1. w/ Front No. 2 Speaker:

    1. Insert the hook into the body hole.

    2. Engage the clip and install the front speaker.



    3. B127674
    4. Connect the speaker connector.



    B114312
  1. Install the 3 antenna cord clamps.

  1. Connect the connector.



  1. w/ Curtain Shield Airbag:



      B117697E01
    1. Install a new special clip and the clip onto a new front pillar garnish.

    2. Engage the 2 clips and the 2 claws and install the front pillar garnish.



  1. w/o Curtain Shield Airbag:



      B117694
    1. Engage the 2 clips and the 2 claws and install the front pillar garnish.



14. INSTALL FRONT PILLAR GARNISH LH


    B114344E01
  1. w/ Curtain Shield Airbag:

    1. Remove the piece of cloth or nylon.



    B127671
  1. w/ Front No. 2 Speaker:

    1. Insert the hook into the body hole.

    2. Engage the clip and install the front speaker.



    3. B127673
    4. Connect the speaker connector.



    B114316
  1. Install the 4 wire harness clamps.



  1. w/ Curtain Shield Airbag:



      B117698E01
    1. Install a new special clip and the clip onto a new front pillar garnish.

    2. Engage the 2 clips and the 2 claws and install the front pillar garnish.



  1. w/o Curtain Shield Airbag:



      B114318
    1. Engage the 2 clips and the 2 claws and install the front pillar garnish.



15. INSTALL MAP LIGHT ASSEMBLY


    B114310
  1. Connect the map light connector.



    B114346
  1. Engage the 4 claws and install the map light.



16. INSTALL ROOM LIGHT ASSEMBLY


    B114347
  1. Engage the 4 claws and install the room light switch base.

  1. Install the roof wire onto the claw of the room light.



    B114348
  1. Engage the 4 claws and install the room light.



    B124366
  1. Engage the 4 claws and install the 2 covers.



    B114349
  1. Engage the 4 claws and install the room light lens.



17. INSTALL VISOR HOLDER RH


    B114350E01
  1. Engage the 2 claws by turning the visor holder clockwise between 60 to 120° and install the visor holder.



18. INSTALL VISOR HOLDER LH

HINT:
Use the same procedure as for the RH side.



19. INSTALL VISOR ASSEMBLY RH


    B114304
  1. Engage the 2 springs and install the visor.

  1. Install the visor shaft into the visor holder.



    B114351
  1. Engage the 4 claws and install the visor bracket cover.



20. INSTALL VISOR ASSEMBLY LH

HINT:
Use the same procedure as for the RH side.



21. INSTALL ASSIST GRIP SUB-ASSEMBLY


B114302

HINT:
The number of the assist grips varies with the specifications.

  1. Engage the 2 springs and install the assist grip.



22. INSTALL COAT HOOK (w/ Coat Hook)


    B127667
  1. Engage the 2 claws and install the coat hook.



    B127668
  1. Engage the 2 claws and close the cover.



23. INSTALL SEAT BELT ANCHOR COVER (for Rear Center Seat Belt 3 Point Type)


    B114467
  1. Engage the 4 claws and install the seat belt anchor cover.



24. INSTALL CENTER PILLAR UPPER GARNISH RH


    B114298
  1. Engage the 3 clips and the 2 hooks and install the center pillar upper garnish.



25. INSTALL CENTER PILLAR UPPER GARNISH LH

HINT:
Use the same procedure as for the RH side.



26. INSTALL CENTER PILLAR LOWER GARNISH RH


    B114297
  1. Engage the 2 clips and the 2 claws and install the center pillar lower garnish.



27. INSTALL CENTER PILLAR LOWER GARNISH LH

HINT:
Use the same procedure as for the RH side.



28. INSTALL FRONT SEAT OUTER BELT ASSEMBLY RH


    B114296
  1. Install the shoulder anchor with the bolt.

    Torque:
    42 N*m{ 430 kgf*cm , 31 ft.*lbf }



29. INSTALL FRONT SEAT OUTER BELT ASSEMBLY LH

HINT:
Use the same procedure as for the RH side.



30. INSTALL SEAT BELT ANCHOR COVER CAP RH


    B114421
  1. Engage the 3 claws and install the seat belt anchor cover cap.



31. INSTALL SEAT BELT ANCHOR COVER CAP LH

HINT:
Use the same procedure as for the RH side.



32. INSTALL ROOF SIDE INNER GARNISH RH


    B114576E01
  1. w/ Curtain Shield Airbag:

    1. for 3 Point Type Rear Center Seat Belt:

      1. Install a new special clip onto the roof side inner garnish.
      2. Pass the rear seat outer belt and the rear center seat outer belt through the slit in the roof side inner garnish.
      3. Engage the 5 clips and install the roof side inner garnish.

    2. for 2 Point Type Rear Center Seat Belt:

      1. Install a new special clip onto the roof side inner garnish.
      2. Pass the rear seat outer belt through the slit in the roof side inner garnish.
      3. Engage the 5 clips and install the roof side inner garnish.



    B114575
  1. w/o Curtain Shield Airbag:

    1. for 3 Point Type Rear Center Seat Belt:

      1. Pass the rear seat outer belt and the rear center seat outer belt through the slit in the roof side inner garnish.
      2. Engage the 5 clips and install the roof side inner garnish.

    2. for 2 Point Type Rear Center Seat Belt:

      1. Pass the rear seat outer belt through the slit in the roof side inner garnish.
      2. Engage the 5 clips and install the roof side inner garnish.



33. INSTALL ROOF SIDE INNER GARNISH LH


    B114578E01
  1. w/ Curtain Shield Airbag:

    1. Install a new special clip onto the roof side inner garnish.

    2. Pass the rear seat outer belt through the slit in the roof side inner garnish.

    3. Engage the 5 clips and install the roof side inner garnish.



    B114577
  1. w/ Curtain Shield Airbag:

    1. Pass the rear seat outer belt through the slit in the roof side inner garnish.

    2. Engage the 5 clips and install the roof side inner garnish.



34. INSTALL REAR CENTER SEAT OUTER BELT ASSEMBLY (for 3 Point Type Rear Center Seat Belt)


    B114468
  1. Engage the 4 claws and install the center belt guide.



    B114461
  1. Install the through anchor with the bolt.

    Torque:
    42 N*m{ 430 kgf*cm , 31 ft.*lbf }



    B114469
  1. Engage the 2 claws and close the slip joint cover.



    B114459
  1. Install the 2 tongue plates.



35. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH


    B114573
  1. w/ Package Tray Trim:

    1. Engage the 3 clips and the 6 claws and install the deck trim side panel.

    2. Tighten the 3 screws.



    B114290
  1. w/o Package Tray Trim:

    1. Engage the 4 clips and the 6 claws and install the deck trim side panel.

    2. Tighten the 2 screws.



36. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH


    B114574
  1. w/ Package Tray Trim:

    1. w/ Luggage Compartment Room Light:

      1. Connect the luggage compartment room light connector.
      2. Engage the 3 clips and the 6 claws and install the deck trim side board.
      3. Tighten the 3 screws.

    2. w/o Luggage Compartment Room Light:

      1. Engage the 3 clips and the 6 claws and install the deck trim side board.
      2. Tighten the 3 screws.



    B114291
  1. w/o Package Tray Trim:

    1. w/ Luggage Compartment Room Light:

      1. Connect the luggage compartment room light connector.
      2. Engage the 4 clips and the 6 claws and install the deck trim side board.
      3. Tighten the 2 screws.

    2. w/o Luggage Compartment Room Light:

      1. Engage the 4 clips and the 6 claws and install the deck trim side board.
      2. Tighten the 2 screws.



37. INSTALL REAR SEAT OUTER BELT ASSEMBLY RH


    B130498
  1. Engage the clip and install the anchor plate.

  1. Tighten the bolt.

    Torque:
    42 N*m{ 430 kgf*cm , 31 ft.*lbf }



    B114289
  1. Install the belt.



38. INSTALL REAR SEAT OUTER BELT ASSEMBLY LH

HINT:
Use the same procedure as for the RH side.



39. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH


    B130370E01
  1. Align the location mark with the paint mark first, and install the rear door opening trim weatherstrip, as shown in the illustration.
    Paint mark: 
    Area
    Color
    RH side
    Purple
    LH side
    Pink



40. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

HINT:
Use the same procedure as for the RH side.



41. INSTALL REAR DOOR SCUFF PLATE RH


    B114287
  1. Engage the 6 claws and install the rear door scuff plate.



42. INSTALL REAR DOOR SCUFF PLATE LH

HINT:
Use the same procedure as for the RH side.



43. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH


    B130371E01
  1. Align the location mark with the paint mark first, and install the front door opening trim weatherstrip, as shown in the illustration.
    Paint mark: 
    Area
    Color
    RH side
    Gold
    LH side
    Silver



44. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

HINT:
Use the same procedure as for the RH side.



45. INSTALL COWL SIDE TRIM BOARD RH


    B114285
  1. Engage the claw and stud bolt and install the cowl side trim board.



46. INSTALL COWL SIDE TRIM BOARD LH

HINT:
Use the same procedure as for the RH side.



47. INSTALL INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY RH


    B114571
  1. Engage the 4 claws and install the instrument panel under cover.



48. INSTALL INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY LH


    B114572
  1. Engage the 3 claws and install the instrument panel under cover.

  1. Tighten the 2 screws.



49. INSTALL FRONT DOOR SCUFF PLATE RH


    B114284
  1. Engage the 8 claws and install the front door scuff plate.



50. INSTALL FRONT DOOR SCUFF PLATE LH

HINT:
Use the same procedure as for the RH side.



51. INSTALL REAR DECK TRIM COVER


    B114283
  1. for Grand Tire:

    1. Engage the 8 claws and install the rear deck trim cover.

    2. Install the 2 clips.



    B117692
  1. for Temper Spare Tire:

    1. Engage the 8 claws and install the rear deck trim cover.

    2. Install the 2 clips.



52. INSTALL REAR SEAT ASSEMBLY LH


    B126922E01
  1. Insert the 2 location pins through the 2 body holes and install the rear seat.

  1. Using "TORX" socket wrench E10, install the 4 bolts in the sequence shown in the illustration.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }



    B114740E01
  1. Install the rear seat cushion.

  1. Using "TORX" socket wrench E10, install the 3 bolts in the sequence shown in the illustration.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }



53. INSTALL REAR SEAT ASSEMBLY RH


    B114684E01
  1. Insert the 2 location pins through the 2 body holes and install the rear seat.

  1. Using "TORX" socket wrench E10, install the 4 bolts in the sequence shown in the illustration.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }



    B114660E01
  1. Install the rear seat cushion.

  1. Using "TORX" socket wrench E10, install the 2 bolts in the sequence shown in the illustration.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }



54. INSTALL NO. 2 REAR SEAT LEG COVER


    B114739
  1. Engage the 3 claws and install the No. 2 rear seat leg cover.



55. INSTALL NO. 1 REAR SEAT LEG COVER
  1. for RH Side:

    1. Install the No. 1 rear seat leg cover .

  1. for LH Side:

    1. Install the No. 1 rear seat leg cover .



56. INSTALL DECK FLOOR BOX RH (w/ Deck Board)


    B106446
  1. Set the deck floor box and lock the 2 knobs.



57. INSTALL DECK FLOOR BOX LH (w/ Deck board)

HINT:
Use the same procedure as for the RH side.



58. INSTALL SPARE WHEEL COVER ASSEMBLY (w/ Deck Board)


    B119913
  1. Install the spare wheel cover.



59. INSTALL DECK BOARD SUB-ASSEMBLY (w/ Deck Board)


    B106447
  1. Set the deck board and lock the 2 knobs.



60. INSTALL REAR FLOOR CARPET ASSEMBLY (w/o Deck Board)


    B119912
  1. Install the rear floor carpet.



61. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Package Trim)


    B114569E01
  1. Engage the 2 claws and install the package tray trim panel.

  1. Install the 5 pieces of hook tape.

  1. Install the 2 package tray trim suspenders.



62. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



63. INSPECT SRS WARNING LIGHT
(Click here)