Home › BODY ELECTRICAL › AUDIO / VISUAL › RADIO ANTENNA CORD (for Sedan)

RADIO ANTENNA CORD (for Sedan) > INSTALLATION

for Preparation Click here


CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (Click here).



1. INSTALL NO. 2 ANTENNA CORD SUB-ASSEMBLY


  1. w/ Curtain Shield Airbag:

    1. Install the antenna cord positioning tapes into the 4 claws of the front and rear side rail spacers.

    2. Align the antenna cord positioning tapes with the markings on the roof headlining.



    3. Install the antenna cord onto the roof headlining with 8 new pieces of tape.


      B138588E01

      Tape size: 
      Mark
      Measurement
      a
      80 mm (3.15 in.)
      b
      20 mm (0.787 in.)

      NOTICE:
      1. Apply the tape securely in place.
      2. Do not touch the adhesive surface when applying the tape to prevent adhesion failure.



  1. w/o Curtain Shield Airbag:

    1. Install the antenna cord positioning tapes into the 6 claws of the front and rear side rail spacers.

    2. Align the antenna cord positioning tapes with the markings on the roof headlining.



    3. Install the antenna cord onto the roof headlining with 6 new pieces of tape.


      B138590E01

      Tape size: 
      Mark
      Measurement
      a
      80 mm (3.15 in.)
      b
      20 mm (0.787 in.)

      NOTICE:
      1. Apply the tape securely in place.
      2. Do not touch the adhesive surface when applying the tape to prevent adhesion failure.



2. INSTALL ROOF HEADLINING ASSEMBLY


    B134793
  1. w/ Curtain Shield Airbag:

    1. Engage the 4 hooks and install the roof headlining.

    2. Install the 2 clips.



    B134794
  1. w/o Curtain Shield Airbag:

    1. Engage the 2 claws and 4 hooks and install the roof headlining.

    2. Install the 2 clips.



    B134788
  1. Connect the antenna connector.

  1. Install the clamp.



3. INSTALL MAP LIGHT ASSEMBLY


    B138432
  1. Connect the map light connector.



    B114346
  1. Engage the 4 claws and install the map light.



4. INSTALL ROOM LIGHT ASSEMBLY


    B138433
  1. Engage the 4 claws and install the room light switch base.

  1. Install the roof wire into the claw of the room light.



    B114348
  1. Engage the 4 claws and install the room light.



    B138434
  1. Engage the 2 claws and install the cover.

    HINT:
    Use the same procedure for both sides.



    B114349
  1. Engage the 4 claws and install the room light lens.



5. INSTALL VISOR HOLDER RH


    B114350E01
  1. Engage the 2 claws by turning the visor holder clockwise between 60 to 120° and install the visor holder.



6. INSTALL VISOR HOLDER LH

HINT:
Use the same procedure as for the RH side.



7. INSTALL VISOR ASSEMBLY RH


    B114304
  1. Engage the 2 springs and install the visor.

  1. Install the visor shaft into the visor holder.



    B114351
  1. Engage the 4 claws and install the visor bracket cover.



8. INSTALL VISOR ASSEMBLY LH

HINT:
Use the same procedure as for the RH side.



9. INSTALL ASSIST GRIP SUB-ASSEMBLY


B134786

HINT:
The number of the assist grips varies with the specifications.



    B114302
  1. Engage the 2 springs and install the assist grip.



10. INSTALL ASSIST GRIP COVER


B134785

HINT:
The number of the assist grip covers varies with the specifications.



    B114352
  1. Engage the 2 claws and install the assist grip cover.



11. INSTALL ROOF HEADLINING SERVICE HOLE COVER (w/o Curtain Shield Airbag)


B134784

HINT:
The number of the roof headlining service hole covers varies with the specifications.



    B114353
  1. Install the roof headlining service hole cover.



12. INSTALL ANTENNA CORD SUB-ASSEMBLY


  1. for LHD:

    1. Install the antenna cord with the 5 clamps

    2. Connect the antenna amplifier connector.



    3. Insert the hook into the body hole and install the bracket with the bolt.


      B138389



  1. for RHD:

    1. Install the antenna cord with the 4 clamps

    2. Connect the antenna amplifier connector.

    3. Connect the plug.



    4. Insert the hook into the body hole and install the bracket with the bolt.


      B138390



13. INSTALL RADIO RECEIVER ASSEMBLY (for LHD)


    B138304
  1. Connect the plug.

  1. Connect the 2 radio connectors.



    B138303
  1. Align the 2 bosses of the instrument panel with the hole in the radio bracket.

  1. Install the radio receiver with the 4 bolts.



14. INSTALL INSTRUMENT CLUSTER CENTER FINISH PANEL SUB-ASSEMBLY (for LHD)


B132395
  1. Engage the 2 claws and 4 clips and install the instrument cluster finish panel center.



15. INSTALL UPPER INSTRUMENT PANEL SUB-ASSEMBLY


B130309E01
  1. Using a nipper, cut off both ends of the runner portion shown in the illustration (When installing a new one).

  1. Engage the 5 claws at the front side of the instrument panel.



  1. Engage the 7 clips at the rear side of the instrument panel.


    B132324



  1. Install the upper instrument panel with the 2 <C> bolts and the 2 <B> screws.


    B132323E01

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf } for bolt <C>



    B132386
  1. Connect the passenger airbag connector and clamp.



16. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY


B132321E01
  1. Engage the claws of the hinge portions by pushing the glove compartment door in the horizontal direction to install the glove compartment door assembly.

    NOTICE:
    Engage the claw by pushing it in the horizontal direction, otherwise, installation failure caused by excessive play around the hinge portion will result.



    B132319E01
  1. Slightly flex the upper portion of the glove compartment door assembly to engage the stopper.

  1. Install the glove compartment door stopper onto the glove compartment door.



17. INSTALL COMBINATION METER ASSEMBLY


E116835E01
  1. Install the combination meter assembly with the 2 screws.

    NOTICE:
    Install the combination meter so that the rib of the combination meter is held between the instrument panel and the instrument cluster finish panel.

  1. Connect the 2 connectors.



18. INSTALL INSTRUMENT CLUSTER FINISH PANEL NO.1


E116833
  1. Fit the 2 claws of the instrument cluster finish panel into the upper instrument cluster finish panel center.



    E116834
  1. Engage the 5 claws and 5 clips and install the instrument cluster finish panel.



19. INSTALL INSTRUMENT PANEL FINISH PANEL END RH


B132318
  1. Engage the 6 claws and 3 clips and install the instrument panel finish panel end RH.



20. INSTALL INSTRUMENT PANEL FINISH PANEL END LH


B132317
  1. Engage the 6 claws and 3 clips and install the instrument panel finish panel end LH.



21. INSTALL INSTRUMENT PANEL LOWER CENTER FINISH PANEL


B132316
  1. Engage the 2 claws and 2 clips and install the instrument panel finish panel lower center.



22. INSTALL FRONT PILLAR GARNISH RH


    B138439E01
  1. w/ Curtain Shield Airbag:

    1. Remove the piece of cloth or nylon.



    B134787
  1. Install the 3 clamps.

  1. Connect the antenna connector.



    B134781E01
  1. w/ Curtain Shield Airbag:

    1. Install a new special clip and the clip onto the front pillar garnish.

    2. Engage the 2 clips and the 2 claws and install the front pillar garnish.



    B134779
  1. w/o Curtain Shield Airbag:

    1. Engage the 2 clips and the 2 claws and install the front pillar garnish.



23. INSTALL FRONT PILLAR GARNISH LH


    B138440
  1. w/ Curtain Shield Airbag:

    1. Remove the piece of cloth or nylon.



    B134789
  1. Install the 4 clamps.



    B134782E01
  1. w/ Curtain Shield Airbag:

    1. Install a new special clip and the clip onto the front pillar garnish.

    2. Engage the 2 clips and the 2 claws and install the front pillar garnish.



    B134780
  1. w/o Curtain Shield Airbag:

    1. Engage the 2 clips and the 2 claws and install the front pillar garnish.



24. INSTALL CENTER PILLAR UPPER GARNISH RH


    B134768
  1. Engage the 2 hooks and 2 clips and install the center pillar upper garnish.



25. INSTALL CENTER PILLAR UPPER GARNISH LH

HINT:
Use the same procedure as for the RH side.



26. INSTALL FRONT SEAT OUTER BELT ASSEMBLY RH


    B114296
  1. Install the through anchor with the bolt.

    Torque:
    42 N*m{ 430 kgf*cm , 31 ft.*lbf }



27. INSTALL FRONT SEAT OUTER BELT ASSEMBLY LH

HINT:
Use the same procedure as for the RH side.



28. INSTALL SEAT BELT ANCHOR COVER CAP


B138431E02

HINT:
Use the same procedure for both sides.

  1. Engage the 3 claws and install the seat belt anchor cover cap.



29. INSTALL CENTER PILLAR LOWER GARNISH RH


    B134767
  1. Engage the 2 clips and 3 claws and install the center pillar lower garnish.



30. INSTALL CENTER PILLAR LOWER GARNISH LH

HINT:
Use the same procedure as for the RH side.



31. INSTALL ROOF SIDE INNER GARNISH RH


    B134775E01
  1. w/ Curtain Shield Airbag:

    1. Install a new special clip and the clip onto the roof side inner garnish.

    2. Engage the 4 clips and the claw and install the roof side inner garnish.



    B134774
  1. w/o Curtain Shield Airbag:

    1. Engage the 4 clips and the claw and install the roof side inner garnish.



32. INSTALL ROOF SIDE INNER GARNISH LH

HINT:
Use the same procedure as for the RH side.



33. INSTALL REAR SEAT SIDE COVER RH


    B134776
  1. Engage the 2 clips and the 4 claws and install the rear seat side cover.



34. INSTALL REAR SEAT SIDE COVER LH

HINT:
Use the same procedure as for the RH side.



35. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH


    B134773E01
  1. Align the location mark with the paint mark first, and install the rear door opening trim weatherstrip, as shown in the illustration.

    Paint mark:
    Area
    Color
    RH side
    Green
    LH side
    Red



36. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

HINT:
Use the same procedure as for the RH side.



37. INSTALL REAR DOOR SCUFF PLATE RH


    B134771
  1. Engage the 7 claws and install the rear door scuff plate.



38. INSTALL REAR DOOR SCUFF PLATE LH

HINT:
Use the same procedure as for the RH side.



39. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH


    B134766E01
  1. Align the location mark with the paint mark first, and install the front door opening trim weatherstrip, as shown in the illustration.

    Paint mark:
    Area
    Color
    RH side
    Blue
    LH side
    Pink



40. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

HINT:
Use the same procedure as for the RH side.



41. INSTALL COWL SIDE TRIM BOARD RH


    B114285
  1. Engage the stud bolt and the claw and install the cowl side trim board.



42. INSTALL COWL SIDE TRIM BOARD LH

HINT:
Use the same procedure as for the RH side.



43. INSTALL FRONT DOOR SCUFF PLATE RH


    B134764
  1. Engage the 11 claws and install the front door scuff plate.



44. INSTALL FRONT DOOR SCUFF PLATE LH

HINT:
Use the same procedure as for the RH side.



45. INSTALL LUGGAGE COMPARTMENT TRIM INNER PAD (for 60/40 Split Seat Type)


B136275
  1. Install the luggage compartment trim inner pad.



46. INSTALL SPARE WHEEL COVER ASSEMBLY (for 60/40 Split Seat Type)


B136270
  1. Install the spare wheel cover.



47. INSTALL LUGGAGE COMPARTMENT FLOOR MAT (for 60/40 Split Seat Type)


B136269
  1. Install the luggage compartment floor mat.



48. INSTALL REAR SEATBACK ASSEMBLY RH (for 60/40 Split Seat Type)


    B134945E01
  1. Insert the 2 hooks into the rear seatback frame hole and install the rear seatback tightening the 2 bolts in the sequence shown in the illustration.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }



    B134944
  1. Install the rear seatback cover with the 2 clips.

  1. Pull up the rear seatback.



    B134943
  1. Install the rear seat outer belt into the rear seat shoulder belt guide.

  1. for 3 Point Type Rear Seat Belt:

    1. Install the rear center seat outer belt into the rear center seat shoulder belt guide.



49. INSTALL REAR SEATBACK ASSEMBLY LH (for 60/40 Split Seat Type)


    B134926E01
  1. Insert the 2 hooks into the rear seatback frame hole and install the rear seatback tightening the 2 bolts in the sequence shown in the illustration.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }



    B134925
  1. Install the rear seatback cover with the 2 clips.

  1. Pull up the rear seatback.



    B134924
  1. Install the rear seat outer belt into the rear seat shoulder belt guide.



50. INSTALL REAR SEATBACK ASSEMBLY (for Fixed Seat Type)


    B134981
  1. Engage the 3 hooks and install the rear seatback.

  1. Tighten the 3 bolts.

    Torque:
    7.9 N*m{ 80 kgf*cm , 70 in.*lbf }



    B138450E02
  1. Install the rear seat outer belt into the rear seat shoulder belt guide.

    HINT:
    Use the same procedure for both sides.

  1. for 3 Point Type Rear Center Seat belt:

    1. Install the rear center seat outer belt into the rear center seat shoulder belt guide.



51. INSTALL REAR SEAT CUSHION COVER PAD SUB-ASSEMBLY
  1. for 60/40 Split Seat Type:

    1. Install the rear seat cushion cover pad sub-assembly .

  1. for Fixed Seat Type:

    1. Install the rear seat cushion cover pad sub-assembly .



52. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



53. INSPECT SRS WARNING LIGHT
(Click here)