ROOF HEADLINING (for Hatchback 5 Door) > INSTALLATION |
| 1. INSTALL REAR SIDE RAIL SPACER RH |
![]() |
w/ Curtain Shield Airbag:
Align a new rear side rail spacer with the markings of the roof headlining and install it onto the roof headlining
![]() |
w/o Curtain Shield Airbag:
Align a new rear side rail spacer with the markings of the roof headlining and install it onto the roof headlining
| 2. INSTALL REAR SIDE RAIL SPACER LH |
| 3. INSTALL FRONT SIDE RAIL SPACER RH |
![]() |
w/ Curtain Shield Airbag:
Align a new front side rail spacer with the markings of the roof headlining and install it onto the roof headlining
![]() |
w/o Curtain Shield Airbag:
Align a new front side rail spacer with the markings of the roof headlining and install it onto the roof headlining
| 4. INSTALL FRONT SIDE RAIL SPACER LH |
| 5. INSTALL ANTENNA CORD SUB-ASSEMBLY |
w/ Curtain Shield Airbag:
Install the part of the antenna cord marked with red positioning tape into claw A of the front side rail spacer.
Install the antenna cord positioning tape into the 2 claws of the front and rear side rail spacers.
Insert the antenna cord positioning tape into the cutout of the roof headlining.
Align the antenna cord positioning tape with the markings of the roof headlining.
Install the antenna cord onto the roof headlining with 6 new pieces of tape.

| Mark | Measurement |
| a | 80 mm (3.15 in.) |
| b | 20 mm (0.787 in.) |
w/o Curtain Shield Airbag:
Install the part of the antenna cord marked with red positioning tape into claw A of the front side rail spacer.
Install the antenna cord positioning tape into the 4 claws of the front and rear side rail spacers.
Insert the antenna cord positioning tape into the cutout of the roof headlining.
Align the antenna cord positioning tape with the markings of the roof headlining.
Install the antenna cord onto the roof headlining with 4 new pieces of tape.

| Mark | Measurement |
| a | 80 mm (3.15 in.) |
| b | 20 mm (0.787 in.) |
| 6. INSTALL NO. 1 ROOF WIRE |
![]() |
w/ Curtain Shield Airbag:
Install the part of the No. 1 roof wire marked with red positioning tape into claw A of the front side rail spacer.
Align the No. 1 roof wire positioning tape with the markings of the roof headlining.
Install the No. 1 roof wire onto the roof headlining with 7 new pieces of tape.
| Mark | Measurement |
| a | 80 mm (3.15 in.) |
| b | 20 mm (0.787 in.) |
![]() |
w/o Curtain Shield Airbag:
Install the part of the No. 1 roof wire marked with red positioning tape into claw A of the front side rail spacer.
Install the No. 1 roof wire positioning tape into the claw of the front side rail spacer.
Align the No. 1 roof wire positioning tape with the markings of the roof headlining.
Install the No. 1 roof wire onto the roof headlining with 6 new pieces of tape.
| Mark | Measurement |
| a | 80 mm (3.15 in.) |
| b | 20 mm (0.787 in.) |
| 7. INSTALL REAR ROOF SILENCER PAD |
![]() |
Align 2 new rear roof silencer pads with the markings of the roof headlining and install them onto the roof headlining.
| 8. INSTALL NO. 1 ROOF SILENCER PAD |
Align 4 new No. 1 roof silencer pads with the markings of the roof headlining and install them onto the roof headlining.

| 9. REMOVE NO. 5 ROOF SILENCER PAD |
![]() |
Align 2 new No. 5 roof silencer pads with the markings of the roof headlining and install them onto the roof headlining.
| 10. INSTALL ROOF HEADLINING ASSEMBLY |
![]() |
Pull the roof headlining back into the vehicle through the back door.
w/ Curtain Shield Airbag:
for 3 Point Type Rear Center Seat Belt:
for 2 Point Type Rear Center Seat Belt:

w/o Curtain Shield Airbag:
for 3 Point Type Rear Center Seat Belt:
for 2 Point Type Rear Center Seat Belt:

![]() |
Install the 2 connectors.
Connect the 2 connectors.
Install the antenna cord onto the antenna cord clamp.
![]() |
for LHD:
Connect the connector.
Install the wiring harness clamp.
![]() |
for RHD:
Connect the connector.
Install the No. 1 roof wire into the claw of the junction block.
![]() |
Install the wiring harness clamp.
| 11. INSTALL INSTRUMENT PANEL BOX |
![]() |
Insert the stopper of the instrument panel box from the cutout of the instrument panel lower.
Engage the 2 hinges with the instrument panel open.
Close the instrument panel box.
| 12. INSTALL UPPER INSTRUMENT PANEL SUB-ASSEMBLY |
![]() |
Using a nipper, cut off both ends of the runner portion shown in the illustration (When installing a new one).
Engage the 5 claws at the upper side of the instrument panel.
Engage the claw and the 3 clips at the lower side of the instrument panel.

Install the instrument panel upper with the 2 <C> bolts and the 4 <B> screws.
Connect the connectors.

![]() |
Connect the passenger airbag connector and clamp.
| 13. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY |
![]() |
Engage the claw of the hinge portion in the horizontal direction to install the glove compartment door assembly.
![]() |
Slightly deform the upper portion of the glove compartment door assembly to engage the stopper.
| 14. INSTALL NO. 1 SWITCH HOLE BASE |
![]() |
Disengage the 2 clips and 2 claws and install the switch hole base.
| 15. INSTALL COMBINATION METER ASSEMBLY |
![]() |
Install the combination meter assembly with the 2 screws.
Connect the 2 connectors.
| 16. INSTALL INSTRUMENT CLUSTER FINISH PANEL NO.1 |
![]() |
Fit the 3 A claws of the instrument cluster finish panel into the upper instrument cluster finish panel center.
![]() |
Engage the 4 claws and 5 clips and install the instrument cluster finish panel.
| 17. INSTALL INSTRUMENT PANEL FINISH PANEL END RH |
![]() |
with CD player
Connect the connector.
Engage the 4 claws and 3 clips and install the instrument panel finish panel end RH.
![]() |
Except CD player
Connect the connector.
Engage the 5 claws and 3 clips and install the instrument panel finish panel end RH.
| 18. INSTALL INSTRUMENT PANEL FINISH PANEL END LH |
![]() |
with CD player
Connect the connector.
Engage the 4 claws and 3 clips and install the instrument panel finish panel end LH.
![]() |
Except CD player
Connect the connector.
Engage the 5 claws and 3 clips and install the instrument panel finish panel end LH.
| 19. INSTALL FRONT PILLAR GARNISH RH |
![]() |
w/ Curtain Shield Airbag:
Remove the piece of cloth or nylon.
![]() |
w/ Front No. 2 Speaker:
Insert the hook into the body hole.
Engage the clip and install the front speaker.
![]() |
Connect the speaker connector.
![]() |
Install the 3 antenna cord clamps.
Connect the connector.
w/ Curtain Shield Airbag:
![]() |
Install a new special clip and the clip onto a new front pillar garnish.
Engage the 2 clips and the 2 claws and install the front pillar garnish.
w/o Curtain Shield Airbag:
![]() |
Engage the 2 clips and the 2 claws and install the front pillar garnish.
| 20. INSTALL FRONT PILLAR GARNISH LH |
![]() |
w/ Curtain Shield Airbag:
Remove the piece of cloth or nylon.
![]() |
w/ Front No. 2 Speaker:
Insert the hook into the body hole.
Engage the clip and install the front speaker.
![]() |
Connect the speaker connector.
![]() |
Install the 4 wire harness clamps.
w/ Curtain Shield Airbag:
![]() |
Install a new special clip and the clip onto a new front pillar garnish.
Engage the 2 clips and the 2 claws and install the front pillar garnish.
w/o Curtain Shield Airbag:
![]() |
Engage the 2 clips and the 2 claws and install the front pillar garnish.
| 21. INSTALL MAP LIGHT ASSEMBLY |
![]() |
Connect the map light connector.
![]() |
Engage the 4 claws and install the map light.
| 22. INSTALL ROOM LIGHT ASSEMBLY |
![]() |
Engage the 4 claws and install the room light switch base.
Install the roof wire onto the claw of the room light.
![]() |
Engage the 4 claws and install the room light.
![]() |
Engage the 4 claws and install the 2 covers.
![]() |
Engage the 4 claws and install the room light lens.
| 23. INSTALL VISOR HOLDER RH |
![]() |
Engage the 2 claws by turning the visor holder clockwise between 60 to 120° and install the visor holder.
| 24. INSTALL VISOR HOLDER LH |
| 25. INSTALL VISOR ASSEMBLY RH |
![]() |
Engage the 2 springs and install the visor.
Install the visor shaft into the visor holder.
![]() |
Engage the 4 claws and install the visor bracket cover.
| 26. INSTALL VISOR ASSEMBLY LH |
| 27. INSTALL ASSIST GRIP SUB-ASSEMBLY |
![]() |
Engage the 2 springs and install the assist grip.
| 28. INSTALL ASSIST GRIP COVER |
![]() |
Engage the 2 claws and install the assist grip cover.
| 29. INSTALL COAT HOOK (w/ Coat Hook) |
![]() |
Engage the 2 claws and install the coat hook.
![]() |
Engage the 2 claws and close the cover.
| 30. INSTALL ROOF HEADLINING SERVICE HOLE COVER (w/o Curtain Shield Airbag) |
![]() |
Install the roof headlining service hole cover.
| 31. INSTALL SEAT BELT ANCHOR COVER (for 3 Point Type Rear Center Seat Belt) |
![]() |
Engage the 4 claws and install the seat belt anchor cover.
| 32. INSTALL CENTER PILLAR UPPER GARNISH RH |
![]() |
Engage the 3 clips and the 2 hooks and install the center pillar upper garnish.
| 33. INSTALL CENTER PILLAR UPPER GARNISH LH |
| 34. INSTALL CENTER PILLAR LOWER GARNISH RH |
![]() |
Engage the 2 clips and the 2 claws and install the center pillar lower garnish.
| 35. INSTALL CENTER PILLAR LOWER GARNISH LH |
| 36. INSTALL FRONT SEAT OUTER BELT ASSEMBLY RH |
![]() |
Install the shoulder anchor with the bolt.
| 37. INSTALL FRONT SEAT OUTER BELT ASSEMBLY LH |
| 38. INSTALL SEAT BELT ANCHOR COVER CAP |
![]() |
Engage the 3 claws and install the seat belt anchor cover cap.
| 39. INSTALL ROOF SIDE INNER GARNISH RH |
![]() |
w/ Curtain Shield Airbag:
for 3 Point Type Rear Center Seat Belt:
for 2 Point Type Rear Center Seat Belt:
![]() |
w/o Curtain Shield Airbag:
for 3 Point Type Rear Center Seat Belt:
for 2 Point Type Rear Center Seat Belt:
| 40. INSTALL ROOF SIDE INNER GARNISH LH |
![]() |
w/ Curtain Shield Airbag:
Install a new special clip onto the roof side inner garnish.
Pass the rear seat outer belt through the slit in the roof side inner garnish.
Engage the 5 clips and install the roof side inner garnish.
![]() |
w/ Curtain Shield Airbag:
Pass the rear seat outer belt through the slit in the roof side inner garnish.
Engage the 5 clips and install the roof side inner garnish.
| 41. INSTALL REAR CENTER SEAT OUTER BELT ASSEMBLY (for 3 Point Type Rear Center Seat Belt) |
![]() |
Engage the 4 claws and install the center belt guide.
![]() |
Install the through anchor with the bolt.
![]() |
Engage the 2 claws and close the slip joint cover.
![]() |
Install the 2 tongue plates.
| 42. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH |
![]() |
w/ Package Tray Trim:
Engage the 3 clips and the 6 claws and install the deck trim side panel.
Tighten the 3 screws.
![]() |
w/o Package Tray Trim:
Engage the 4 clips and the 6 claws and install the deck trim side panel.
Tighten the 2 screws.
| 43. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH |
![]() |
w/ Package Tray Trim:
w/ Luggage Compartment Room Light:
w/o Luggage Compartment Room Light:
![]() |
w/o Package Tray Trim:
w/ Luggage Compartment Room Light:
w/o Luggage Compartment Room Light:
| 44. INSTALL REAR SEAT OUTER BELT ASSEMBLY RH |
![]() |
Engage the clip and install the anchor plate.
Tighten the bolt.
![]() |
Install the belt.
| 45. INSTALL REAR SEAT OUTER BELT ASSEMBLY LH |
| 46. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH |
![]() |
Align the location mark with the paint mark first, and install the rear door opening trim weatherstrip, as shown in the illustration.
| Area | Color |
| RH side | Purple |
| LH side | Pink |
| 47. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH |
| 48. INSTALL REAR DOOR SCUFF PLATE RH |
![]() |
Engage the 6 claws and install the rear door scuff plate.
| 49. INSTALL REAR DOOR SCUFF PLATE LH |
| 50. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH |
![]() |
Align the location mark with the paint mark first, and install the front door opening trim weatherstrip, as shown in the illustration.
| Area | Color |
| RH side | Gold |
| LH side | Silver |
| 51. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH |
| 52. INSTALL COWL SIDE TRIM BOARD RH |
![]() |
Engage the claw and stud bolt and install the cowl side trim board.
| 53. INSTALL COWL SIDE TRIM BOARD LH |
| 54. INSTALL INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY RH |
![]() |
Engage the 4 claws and install the instrument panel under cover.
| 55. INSTALL INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY LH |
![]() |
Engage the 3 claws and install the instrument panel under cover.
Tighten the 2 screws.
| 56. INSTALL FRONT DOOR SCUFF PLATE RH |
![]() |
Engage the 8 claws and install the front door scuff plate.
| 57. INSTALL FRONT DOOR SCUFF PLATE LH |
| 58. INSTALL REAR DECK TRIM COVER |
![]() |
for Grand Tire:
Engage the 8 claws and install the rear deck trim cover.
Install the 2 clips.
![]() |
for Temper Spare Tire:
Engage the 8 claws and install the rear deck trim cover.
Install the 2 clips.
| 59. INSTALL REAR SEAT ASSEMBLY LH |
![]() |
Insert the 2 location pins through the 2 body holes and install the rear seat.
Using "TORX" socket wrench E10, install the 4 bolts in the sequence shown in the illustration.
![]() |
Install the rear seat cushion.
Using "TORX" socket wrench E10, install the 3 bolts in the sequence shown in the illustration.
| 60. INSTALL REAR SEAT ASSEMBLY RH |
![]() |
Insert the 2 location pins through the 2 body holes and install the rear seat.
Using "TORX" socket wrench E10, install the 4 bolts in the sequence shown in the illustration.
![]() |
Install the rear seat cushion.
Using "TORX" socket wrench E10, install the 2 bolts in the sequence shown in the illustration.
| 61. INSTALL NO. 2 REAR SEAT LEG COVER |
![]() |
Engage the 3 claws and install the No. 2 rear seat leg cover.
| 62. INSTALL NO. 1 REAR SEAT LEG COVER |
for RH Side:
Install the No. 1 rear seat leg cover .
for LH Side:
Install the No. 1 rear seat leg cover .
| 63. INSTALL DECK FLOOR BOX RH (w/ Deck Board) |
![]() |
Set the deck floor box and lock the 2 knobs.
| 64. INSTALL DECK FLOOR BOX LH (w/ Deck Board) |
| 65. INSTALL SPARE WHEEL COVER ASSEMBLY (w/ Deck Board) |
![]() |
Install the spare wheel cover.
| 66. INSTALL DECK BOARD SUB-ASSEMBLY (w/ Deck Board) |
![]() |
Set the deck board and lock the 2 knobs.
| 67. INSTALL REAR FLOOR CARPET ASSEMBLY (w/o Deck Board) |
![]() |
Install the rear floor carpet.
| 68. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Package Tray Trim) |
![]() |
Engage the 2 claws and install the package tray trim panel.
Install the 5 pieces of hook tape.
Install the 2 package tray trim suspenders.
| 69. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 70. INSPECT SRS WARNING LIGHT |