CURTAIN SHIELD AIRBAG ASSEMBLY (for Sedan) > INSTALLATION |
| 1. INSTALL ROOF SIDE RAIL BRACKET RH |
![]() |
Insert the 2 hooks into the body holes and install the roof side rail bracket and tighten 2 the bolts.
| 2. INSTALL CURTAIN SHIELD AIRBAG BRACKET RH |
![]() |
Insert the 2 hooks into the body holes and install the curtain shield back bracket and tighten 1 the bolt.
| 3. INSTALL CURTAIN SHIELD AIRBAG ASSEMBLY |
Insert the 3 hooks into the body holes and install the curtain shield back bracket and tighten 9 the bolts.

![]() |
Connect the airbag connector.
| 4. INSTALL ROOF HEADLINING ASSEMBLY |
![]() |
Install the roof headlining into the front door.
![]() |
w/ Curtain Shield Airbag:
Engage the 4 hooks.
Install the 2 clips.
![]() |
w/o Curtain Shield Airbag:
Engage the 2 claws and 4 hooks.
Install the 2 clips.
![]() |
Connect the antenna connector.
Install the clamp.
![]() |
for LHD:
Connect the roof wire connector.
![]() |
for RHD:
Install the roof wire into the clamp.
Connect the roof wire connector.
![]() |
Install the 2 clamps.
| 5. INSTALL MAP LIGHT ASSEMBLY |
![]() |
Connect the map light connector.
![]() |
Engage the 4 claws and install the map light.
| 6. INSTALL ROOM LIGHT ASSEMBLY |
![]() |
Connect the map light connector.
![]() |
Engage the 4 claws and install the map light.
| 7. INSTALL VISOR HOLDER RH |
![]() |
Engage the 2 claws by turning the visor holder clockwise between 60 to 120° and install the visor holder.
| 8. INSTALL VISOR HOLDER LH |
| 9. INSTALL VISOR ASSEMBLY RH |
![]() |
Engage the 2 springs and install the visor.
Install the visor shaft into the visor holder.
![]() |
Engage the 4 claws and install the visor bracket cover.
| 10. INSTALL VISOR ASSEMBLY LH |
| 11. INSTALL ASSIST GRIP SUB-ASSEMBLY |
![]() |
![]() |
Engage the 2 springs and install the assist grip.
| 12. INSTALL ASSIST GRIP COVER |
![]() |
![]() |
Engage the 2 claws and install the assist grip cover.
| 13. INSTALL INSTRUMENT PANEL BOX (for LHD) |
Insert the stopper of the instrument panel box from the cutout of the instrument panel lower.
![]() |
Engage the 2 hinges with the instrument panel open.
Close the instrument panel box.
| 14. INSTALL INSTRUMENT UPPER PANEL SUB-ASSEMBLY |
![]() |
Using a nipper, cut off both ends of the runner portion shown in the illustration (When installing a new one).
Engage the 5 claws at the front side of the instrument panel.
Engage the 7 clips at the rear side of the instrument panel.

Install the upper instrument panel with the 2 <C> bolts and the 2 <B> screws.

![]() |
Connect the passenger airbag connector and clamp.
| 15. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY |
![]() |
Engage the claws of the hinge portions by pushing the glove compartment door in the horizontal direction to install the glove compartment door assembly.
![]() |
Slightly flex the upper portion of the glove compartment door assembly to engage the stopper.
Install the glove compartment door stopper onto the glove compartment door.
| 16. INSTALL COMBINATION METER ASSEMBLY |
![]() |
Install the combination meter assembly with the 2 screws.
Connect the 2 connectors.
| 17. INSTALL INSTRUMENT CLUSTER FINISH PANEL NO.1 |
![]() |
Fit the 2 claws of the instrument cluster finish panel into the upper instrument cluster finish panel center.
![]() |
Engage the 5 claws and 5 clips and install the instrument cluster finish panel.
| 18. INSTALL INSTRUMENT PANEL FINISH PANEL END RH |
![]() |
Engage the 6 claws and 3 clips and install the instrument panel finish panel end RH.
| 19. INSTALL INSTRUMENT PANEL FINISH PANEL END LH |
![]() |
Engage the 6 claws and 3 clips and install the instrument panel finish panel end LH.
| 20. INSTALL REAR CONSOLE BOX ASSEMBLY |
![]() |
Engage the 4 claws and install the rear console box.
Install the 2 bolts and 2 screws.
Connect the clamp.
| 21. INSTALL CONSOLE BOX CARPET |
![]() |
Install the console box carpet.
| 22. INSTALL REAR CONSOLE BOX UPPER REAR PANEL SUB-ASSEMBLY |
![]() |
Connect the connector.
Engage the 3 clips and 3 claws and install the console upper rear panel.
| 23. INSTALL REAR CONSOLE BOX UPPER FRONT PANEL SUB-ASSEMBLY |
![]() |
Engage the 5 clips and the claw and install the upper console panel.
| 24. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transaxle) |
![]() |
Install the shift lever knob.
| 25. INSTALL INSTRUMENT LOWER CENTER PANEL FINISH PANEL |
![]() |
Engage the 2 claws and 2 clips and install the instrument panel finish panel lower center.
| 26. INSTALL FRONT PILLAR GARNISH RH |
![]() |
Remove the piece of cloth or nylon.
![]() |
Install the 3 clamps.
Connect the antenna connector.
![]() |
Install a new special clip and the clip onto a new front pillar garnish.
Engage the 2 clips and the 2 claws and install the front pillar garnish.
| 27. INSTALL FRONT PILLAR GARNISH LH |
![]() |
Remove the piece of cloth or nylon.
![]() |
Install the 4 clamps.
![]() |
Install a new special clip and the clip onto the front pillar garnish.
Engage the 2 clips and the 2 claws and install the front pillar garnish.
| 28. INSTALL CENTER PILLAR UPPER GARNISH RH |
![]() |
Engage the 2 hooks and 2 clips and install the center pillar upper garnish.
| 29. INSTALL CENTER PILLAR UPPER GARNISH LH |
| 30. INSTALL FRONT SEAT OUTER BELT ASSEMBLY RH |
![]() |
Install the through anchor with the bolt.
| 31. INSTALL FRONT SEAT OUTER BELT ASSEMBLY LH |
| 32. INSTALL SEAT BELT ANCHOR COVER CAP |
![]() |
Engage the 3 claws and install the seat belt anchor cover cap.
| 33. INSTALL CENTER PILLAR LOWER GARNISH RH |
![]() |
Engage the 2 hooks and 2 clips and install the center pillar upper garnish.
| 34. INSTALL CENTER PILLAR LOWER GARNISH LH |
| 35. INSTALL ROOF SIDE INNER GARNISH RH |
![]() |
w/ Curtain Shield Airbag:
Install a new special clip and the clip onto the roof side inner garnish.
Engage the 4 clips and the claw and install the roof side inner garnish.
![]() |
w/o Curtain Shield Airbag:
Engage the 4 clips and the claw and install the roof side inner garnish.
| 36. INSTALL ROOF SIDE INNER GARNISH LH |
| 37. INSTALL REAR SEAT SIDE COVER RH |
![]() |
Engage the 2 clips and the 4 claws and install the rear seat side cover.
| 38. INSTALL REAR SEAT SIDE COVER LH |
| 39. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH |
![]() |
Align the location mark with the paint mark first, and install the front door opening trim weatherstrip, as shown in the illustration.
| Area | Color |
| RH side | Blue |
| LH side | Pink |
| 40. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH |
| 41. INSTALL REAR DOOR SCUFF PLATE RH |
![]() |
Engage the 7 claws and install the rear door scuff plate.
| 42. INSTALL REAR DOOR SCUFF PLATE LH |
| 43. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH |
![]() |
Align the location mark with the paint mark first, and install the front door opening trim weatherstrip, as shown in the illustration.
| Area | Color |
| RH side | Blue |
| LH side | Pink |
| 44. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH |
| 45. INSTALL COWL SIDE TRIM BOARD RH |
![]() |
Engage the stud bolt and the claw and install the cowl side trim board.
| 46. INSTALL COWL SIDE TRIM BOARD LH |
| 47. INSTALL FRONT DOOR SCUFF PLATE RH |
![]() |
Engage the 11 claws and install the front door scuff plate.
| 48. INSTALL FRONT DOOR SCUFF PLATE LH |
| 49. INSTALL LUGGAGE COMPARTMENT TRIM INNER PAD (for 60/40 Split Seat Type) |
![]() |
Install the luggage compartment trim inner pad.
| 50. INSTALL SPARE WHEEL COVER ASSEMBLY (for 60/40 Split Seat Type) |
![]() |
Install the spare wheel cover.
| 51. INSTALL LUGGAGE COMPARTMENT FLOOR MAT (for 60/40 Split Seat Type) |
![]() |
Install the luggage compartment floor mat.
| 52. INSTALL REAR SEATBACK ASSEMBLY (for Fixed Seat Type) |
![]() |
Engage the 3 hooks and install the rear seatback.
Tighten the 3 bolts.
![]() |
Install the rear seat outer belt into the rear seat shoulder belt guide.
for 3 Point Type Rear Center Seat belt:
Install the rear center seat outer belt into the rear center seat shoulder belt guide.
| 53. INSTALL REAR SEATBACK ASSEMBLY LH (for 60/40 Split Seat Type) |
![]() |
Insert the 2 hooks into the rear seatback frame hole and install the rear seatback tightening the 2 bolts in the sequence shown in the illustration.
![]() |
Install the rear seatback cover with the 2 clips.
Pull up the rear seatback.
![]() |
Install the rear seat outer belt into the rear seat shoulder belt guide.
| 54. INSTALL REAR SEATBACK ASSEMBLY RH (for 60/40 Split Seat Type) |
![]() |
Insert the 2 hooks into the rear seatback frame hole and install the rear seatback tightening the 2 bolts in the sequence shown in the illustration.
![]() |
Install the rear seatback cover with the 2 clips.
Pull up the rear seatback.
![]() |
Install the rear seat outer belt into the rear seat shoulder belt guide.
for 3 Point Type Rear Seat Belt:
Install the rear center seat outer belt into the rear center seat shoulder belt guide.
| 55. INSTALL REAR SEAT CUSHION COVER PAD SUB-ASSEMBLY |
for 60/40 Split Seat Type:
Install the rear seat cushion cover pad sub-assembly .
for Fixed Seat Type:
Install the rear seat cushion cover pad sub-assembly .
| 56. INSTALL FRONT SEAT ASSEMBLY LH |
![]() |
Insert the 2 locating pins through the 2 body holes, place the front seat in the most forward position, and then make sure that the inner and outer seat tracks are locked securely.
Using "TORX" socket wrench E10, tighten bolt 1 and then bolt 2 on the rear side.
Move the front seat to the most rearward position, and then make sure that the inner and outer seat tracks are locked securely.
Using "TORX" socket wrench E10, tighten bolt 3 and then bolt 4 on the front side.
![]() |
w/ Front Seat Side Airbag:
Connect the airbag connector.
Connect the buckle switch connector.
| 57. INSTALL FRONT SEAT ASSEMBLY RH |
| 58. INSTALL FRONT SEAT HEADREST ASSEMBLY |
![]() |
Push in the lock button of the front seat headrest support and install the front seat headrest.
| 59. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 60. INSPECT SRS WARNING LIGHT |