Home › TRANSMISSION ยท U340E AUTOMATIC TRANSAXLE › AUTOMATIC TRANSAXLE ASSEMBLY (for Sedan)

AUTOMATIC TRANSAXLE ASSEMBLY (for Sedan) > INSTALLATION

for Preparation Click here



1. INSTALL TRANSMISSION OIL FILLER TUBE SUB-ASSEMBLY


    C118510
  1. Coat a new O-ring with Toyota Genuine ATF WS, and install it onto the oil filler tube.

  1. Install the oil filler tube onto the automatic transaxle with the bolt.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



2. INSTALL TRANSMISSION OIL LEVEL GAUGE SUB-ASSEMBLY
  1. Install the oil level gauge into the transmission oil filler tube.



3. INSTALL NO. 2 OIL COOLER TUBE CLAMP


    C118508
  1. Provisionally install the outlet No. 1 oil cooler tube into the oil cooler tube union.

  1. Provisionally install the inlet No. 1 oil cooler tube into the oil cooler tube union.

  1. Install the No. 2 oil cooler tube clamp onto the transmission oil filler tube with the bolt.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



4. INSTALL OUTLET NO. 1 OIL COOLER TUBE


    C157433E03
  1. Using a union nut wrench, install the outlet No. 1 oil cooler tube while holding the oil cooler tube union with a wrench.

    Torque:
    For use without union nut wrench:
    34 N*m{ 347 kgf*cm , 25 ft.*lbf }
    For use with union nut wrench:
    32 N*m{ 327 kgf*cm , 24 ft.*lbf }

    HINT:
    1. This torque value can be obtained by using a torque wrench with a fulcrum length of 345 mm (13.58 in.) and a union nut wrench with a fulcrum length of 30 mm (1.18 in.).
    2. This torque value is effective when the union nut wrench is parallel to the torque wrench.



5. INSTALL INLET NO. 1 OIL COOLER TUBE


    C157434E03
  1. Using a union nut wrench, install the inlet No. 1 oil cooler tube while holding the oil cooler tube union with a wrench.

    Torque:
    For use without union nut wrench:
    34 N*m{ 347 kgf*cm , 25 ft.*lbf }
    For use with union nut wrench:
    32 N*m{ 327 kgf*cm , 24 ft.*lbf }

    HINT:
    1. This torque value can be obtained by using a torque wrench with a fulcrum length of 345 mm (13.58 in.) and a union nut wrench with a fulcrum length of 30 mm (1.18 in.).
    2. This torque value is effective when the union nut wrench is parallel to the torque wrench.



6. INSTALL NO. 1 TRANSMISSION CONTROL CABLE BRACKET


    C121647
  1. Install the No. 1 transmission control cable bracket onto the automatic transaxle with the 2 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



7. INSTALL SPEEDOMETER DRIVEN HOLE COVER SUB-ASSEMBLY (w/ ABS)


    C121659
  1. Coat a new O-ring with Toyota Genuine ATF WS and install it into the speedometer driven hole cover.

  1. Install the speedometer driven hole cover onto the automatic transaxle.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }



8. INSTALL SPEEDOMETER DRIVEN GEAR (w/o ABS)


    C117097E02
  1. Coat a new O-ring with Toyota Genuine ATF Type WS and install it onto the speedometer sensor.

  1. Install the driven gear into the speedometer sensor with the clip.



9. INSTALL SPEEDOMETER SENSOR (w/o ABS)


    C117096E01
  1. Install the speedometer sensor with the bolt.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. Connect the speedometer sensor connector.



10. INSTALL TORQUE CONVERTER ASSEMBLY


    D025371E07
  1. Set the key at the top of the front oil pump drive gear and put a mark on the housing.



    C057914E03
  1. Put a mark on the torque converter so that its groove is clearly indicated.



    C062931E03
  1. Align the mark on the case with the one on the torque converter and fit the spline of the input shaft to the spline of the turbine runner.



    C062932E03
  1. Rotating the torque converter, fit the spline of the stator shaft with that of the stator.

    HINT:
    Rotate it approximately 180 degrees.



    C062933E03
  1. Rotating the torque converter, align the mark on the case with the one on the torque converter again and fit the key of the oil pump drive gear into the keyway of the torque converter.

    NOTICE:
    Do not push the torque converter excessively when rotating it.



    C192760E01
  1. Using a vernier caliper and a straightedge, measure the dimension A between the automatic transaxle fitting surface (*1) of the engine and the torque converter fitting surface (*2) of the drive plate.

    NOTICE:
    Subtract the thickness of the straightedge from the measured value to gain dimension A.

    HINT:
    The converter fitting surface and the ring gear side surface are at the same level.



    C191549E02
  1. Using a vernier caliper and a straightedge, measure dimension B shown in the illustration and check that dimension B is greater than dimension A, which was measured in step (f).

    Standard:
    A + 1 mm (0.04 in.) or more

    NOTICE:
    Subtract the thickness of the straightedge from the measured value to gain dimension B.



11. INSTALL AUTOMATIC TRANSAXLE ASSEMBLY


    C192761E01
  1. Apply clutch spline grease to the round of the crankshaft contact surface (*1) with the torque converter centerpiece.

    Clutch spline grease:
    Toyota Genuine Clutch Spline Grease or equivalent
    Maximum spread:
    Approximately 1 g (0.353 oz)



    C118504
  1. Install the automatic transaxle onto the engine with the 7 bolts.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }

    NOTICE:
    1. Confirm that 2 knock pins are on the transaxle fitting surface of the engine block before transaxle installation.
    2. After installing the transmission, confirm that the torque converter rotates smoothly.



    A057108E02
  1. Remove any adhesive remaining in the 6 bolt holes of the torque converter clutch and 6 bolts.

  1. Apply adhesive to 2 or 3 threads on the end of the 6 bolts.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



    C118503
  1. Install the 6 torque converter set bolts while holding the crankshaft pulley bolt with a wrench.

    Torque:
    28 N*m{ 286 kgf*cm , 21 ft.*lbf }

    HINT:
    First install the black colored bolt, and then install the 5 silver colored bolts.



    C118502
  1. Install the flywheel housing under cover.



12. INSTALL ENGINE MOUNTING BRACKET LH


    A057108E02
  1. Remove any adhesive remaining in the 4 bolt holes on the engine mounting bracket LH and 4 bolts.

  1. Apply adhesive to 2 or 3 threads on the end of the 4 bolts.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



    C159391
  1. Install the engine mounting bracket LH to the automatic transaxle with the 4 bolts.

    Torque:
    64 N*m{ 653 kgf*cm , 47 ft.*lbf }



13. INSTALL ENGINE MOUNTING INSULATOR LH


    C159389
  1. Install the engine mounting insulator LH with the 5 bolts.

    Torque:
    52 N*m{ 530 kgf*cm , 38 ft.*lbf }



    C159390
  1. Install the engine mounting insulator LH and the engine mounting bracket LH with the bolt and nut.

    Torque:
    52 N*m{ 530 kgf*cm , 38 ft.*lbf }



14. INSTALL NO. 2 ENGINE MOVING CONTROL ROD


    C118499E01
  1. Install the No. 2 engine moving control rod onto the automatic transaxle with the 3 bolts.

    Torque:
    64 N*m{ 653 kgf*cm , 47 ft.*lbf }



15. INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY
  1. Support the front suspension crossmember with a transmission jack.



    A108973E07
  1. Provisionally install the front suspension crossmember onto the body with the 6 bolts.
    Text in Illustration 
    *1
    Bolt A
    *2
    Bolt B
    *3
    Bolt C
    *a
    Front Side
    Bolt
    Underhead Length (mm)
    A
    38
    B
    99
    C
    45



  1. By inserting SST into the datum holes in the front suspension crossmembers RH and LH alternately, tighten bolts A, B and C on both sides to the specified torque, in several steps.


    C230201E01


    Text in Illustration 
    *1
    Bolt A
    *2
    Bolt B
    *3
    Bolt C
    *4
    for Bolt B with Bolt Strength Class 11T
    *5
    for Bolt B with Bolt Strength Class 10T
    -
    -
    *a
    Front Side
    *b
    Datum Hole
    *c
    OK
    *d
    NG
    SST
    09670-00011  

    Torque:
    Bolt A:
    87 N*m{ 887 kgf*cm , 64 ft.*lbf }
    Bolt B with Bolt Strength Class 11T:
    160 N*m{ 1631 kgf*cm , 118 ft.*lbf }
    Bolt B with Bolt Strength Class 10T:
    151 N*m{ 1540 kgf*cm , 111 ft.*lbf }
    Bolt C:
    98 N*m{ 999 kgf*cm , 72 ft.*lbf }

    NOTICE:
    1. Insert SST into the datum hole in a vertical orientation.
    2. If SST cannot be inserted into the datum hole vertically, loosen all the bolts and then insert SST again.

  1. Install the engine moving control rod with the bolt.

    Torque:
    120 N*m{ 1224 kgf*cm , 89 ft.*lbf }



16. INSTALL OIL COOLER HOSE


    C118497
  1. Install the inlet oil cooler hose onto the inlet No. 1 oil cooler tube.

  1. Install the outlet oil cooler hose onto the outlet No. 1 oil cooler tube.



17. INSTALL FRONT DRIVE SHAFT ASSEMBLY LH
  1. for Automatic Transaxle:

    1. Coat the spline of the inboard joint with ATF.

  1. for Manual Transaxle:

    1. Coat the spline of the inboard joint with gear oil.



    C116899
  1. Align the inboard joint splines and install the drive shaft with a screwdriver and hammer.

    NOTICE:
    1. Face the cut area of the front drive inboard joint hole snap ring downward.
    2. Do not damage the oil seal.
    3. Do not damage the inboard joint boot.

    HINT:
    Confirm whether the drive shaft is securely driven in by checking the reaction force and sound.



18. INSTALL FRONT DRIVE SHAFT ASSEMBLY RH

HINT:
The installation procedure for the RH side is the same as that for the LH side.



19. INSTALL AUTOMATIC TRANSMISSION CASE PROTECTOR (w/o ABS)


    C121812
  1. Install the transmission case protector with the 2 bolts.

    Torque:
    23 N*m{ 235 kgf*cm , 17 ft.*lbf }



20. INSTALL FRONT AXLE ASSEMBLY LH
  1. Push the front axle out of the vehicle to align the spline of the drive shaft with the front axle and insert the front axle.

    NOTICE:
    1. Do not push the front axle further out of the vehicle than is necessary.
    2. Do not damage the outboard joint boot.
    3. Check for any foreign matter on the speed sensor rotor and insertion part.
    4. Do not damage the speed sensor rotor.



21. INSTALL FRONT AXLE ASSEMBLY RH

HINT:
Use the same procedure for the LH side and RH side.



22. INSTALL FRONT SUSPENSION LOWER ARM LH


    C107513
  1. Install the lower arm onto the steering knuckle with a new castle nut.

    Torque:
    98 N*m{ 1000 kgf*cm , 72 ft.*lbf }

    NOTICE:
    If the holes for the clip are not aligned, tighten the nut by a further turn of up to 60°.

  1. Install a new clip.



23. INSTALL FRONT SUSPENSION LOWER ARM RH

HINT:
Use the same procedure for the LH side and RH side.



24. INSTALL TIE ROD END SUB-ASSEMBLY LH


    C107961
  1. Install the tie rod end onto the steering knuckle with a new castle nut.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }

    NOTICE:
    If the holes for the clip are not aligned, tighten the nut by a further turn of up to 60°.

  1. Install a new cotter pin.



25. INSTALL TIE ROD END SUB-ASSEMBLY RH

HINT:
Use the same procedure for the LH side and RH side.



26. INSTALL FRONT STABILIZER LINK ASSEMBLY LH


    C106044
  1. Install the stabilizer link with the nut.

    Torque:
    74 N*m{ 755 kgf*cm , 55 ft.*lbf }

    HINT:
    If the ball joint turns together with the nut, use a socket hexagon wrench 6 to hold the stud.



27. INSTALL FRONT STABILIZER LINK ASSEMBLY RH

HINT:
Use the same procedure for the LH side and RH side.



28. INSTALL FRONT SPEED SENSOR LH (w/ ABS)


    C112274
  1. Install the speed sensor onto the steering knuckle with the bolt.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

    NOTICE:
    1. Check that the speed sensor tip and installation portion are free of foreign matter.
    2. Install the speed sensor without turning it from its original installation angle.



    C125274
  1. Install the flexible hose and speed sensor with the bolt.

    Torque:
    29 N*m{ 300 kgf*cm , 22 ft.*lbf }

    NOTICE:
    Install the flexible hose and speed sensor without twisting them.



29. INSTALL FRONT SPEED SENSOR RH (w/ ABS)

HINT:
Use the same procedure for the LH side and RH side.



30. INSTALL FRONT FLEXIBLE HOSE LH (w/o ABS)


    C186418
  1. Install the flexible hose with the bolt.

    Torque:
    29 N*m{ 300 kgf*cm , 22 ft.*lbf }

    NOTICE:
    Install the flexible hose and speed sensor without twisting them.



31. INSTALL FRONT FLEXIBLE HOSE RH (w/o ABS)

HINT:
Use the same procedure for the LH side and RH side.



32. INSTALL FRONT AXLE HUB NUT LH


    C057566
  1. Using a 30 mm socket wrench, install a new axle hub nut.

    Torque:
    216 N*m{ 2203 kgf*cm , 160 ft.*lbf }

  1. Using a chisel and hammer, stake the axle hub nut.



33. INSTALL FRONT AXLE HUB NUT RH

HINT:
Use the same procedure for the LH side and RH side.



34. INSTALL STARTER ASSEMBLY


A104498
  1. Install the starter assembly with the 2 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

  1. Connect the connector.

  1. Connect terminal 30 with the nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 7.2 ft.*lbf }

  1. Close the terminal cap.



35. CONNECT WIRE HARNESS


    C118496
  1. Install the 3 wire harness clamp brackets onto the automatic transaxle with the 3 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



36. CONNECT CONNECTOR
  1. w/o ABS:
    Connect the speedometer sensor connector.

  1. Connect the transmission revolution sensor connector.

  1. Connect the transmission wire connector and install the clamp onto the engine mount insulator.

  1. Connect the park/neutral position switch connector and install the clamp onto the engine mount insulator.



37. INSTALL NO. 3 ENGINE WIRE


    C118495
  1. Install the No. 3 engine wire onto the automatic transaxle with the bolt.

    Torque:
    26 N*m{ 260 kgf*cm , 19 ft.*lbf }

  1. Install the 2 clamps onto the engine mount insulator.



38. INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY


C117100E01
  1. Install the transmission control cable onto the control shaft lever with the nut.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }

  1. Install the transmission control cable into the bracket with the new clip.



39. INSTALL BATTERY CARRIER


A117309
  1. Install the battery carrier with the 5 bolts.

    Torque:
    17 N*m{ 173 kgf*cm , 13 ft.*lbf }

  1. Install the clamp.



40. INSTALL AIR CLEANER BRACKET


A117308
  1. Install the air cleaner bracket with the 2 bolts.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }

  1. Connect the wire harness clamp to the air cleaner bracket.



41. INSTALL AIR CLEANER ASSEMBLY


A104895
  1. Install the air cleaner case with air cleaner inlet No. 1 with the 2 bolts.

    Torque:
    7.8 N*m{ 80 kgf*cm , 69 in.*lbf }

  1. Connect the wire harness to the air cleaner case.

  1. Install the air cleaner element.



    A117355
  1. Install and lock the air cleaner cap and air cleaner hose and then tighten the air cleaner hose clamp.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }

  1. Connect the ventilation hose to the air cleaner hose.

  1. Connect the vacuum switching valve connector and wire harness clamp.

  1. Connect the fuel vapor feed hose and fuel vapor feed hose No. 1 to the vacuum switching valve assembly.

  1. Connect the intake air flow meter connector and wire harness clamp.



42. INSTALL NO. 2 CYLINDER HEAD COVER


A116235E01
  1. Tighten 2 A nuts, then 2 B nuts .

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }



43. INSTALL OUTER COWL TOP PANEL (for LHD)


A128448
  1. Install the cowl top panel outer with the 8 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 57 in.*lbf }



    A128447
  1. Install the cowl top to cowl inner brace with the 2 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 57 in.*lbf }



    A128446
  1. Connect the wire harness clamp.



44. INSTALL OUTER COWL TOP PANEL (for RHD)


A128448
  1. Install the cowl top panel outer with the 8 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 57 in.*lbf }



    A128447
  1. Install the cowl top to cowl inner brace with the 2 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 57 in.*lbf }



    A128446
  1. Connect the wire harness clamp.



45. INSTALL FRONT AIR SHUTTER SEAL (for LHD)


A133324
  1. Engage the 3 claws to install the front air shutter seal.



46. INSTALL FRONT AIR SHUTTER SEAL (for RHD)


A133324
  1. Engage the 3 claws to install the front air shutter seal.



47. INSTALL FRONT WIPER MOTOR AND LINK


    E127840
  1. Connect the connector.

  1. Slide the wiper link as shown in the illustration and engage the rubber pin with the body.

  1. Install the front wiper motor and link with the 2 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



48. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for LHD)


    E127839
  1. Connect the washer hoses.

  1. Engage the 5 hooks.



    E127838
  1. Engage the 8 hooks and the 4 claws.

  1. Install the cowl top ventilator louver sub-assembly with the 3 clips.



49. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for RHD)


    E127836
  1. Connect the washer hoses.

  1. Engage the 5 hooks.



    E127835
  1. Engage the 10 hooks and the 6 claws.

  1. Install the cowl top ventilator louver sub-assembly with the 2 clips.



50. INSTALL COWL SIDE VENTILATOR SUB-ASSEMBLY LH


    E129651
  1. Engage the 3 claws and install the cowl side ventilator sub-assembly LH.



51. INSTALL COWL SIDE VENTILATOR SUB-ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



52. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH


    E058837E10
  1. Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.



    E113862E01
  1. Align the blade tip with the mark on the windshield glass, as shown in the illustration.

  1. Tighten the nut of the front wiper arm.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }



53. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH


    E058837E10
  1. Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.



    E129694E01
  1. Align the blade tip with the mark on the windshield glass, as shown in the illustration.

  1. Tighten the nut of the front wiper arm.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }



54. INSTALL FRONT WIPER ARM HEAD CAP


    E127841
  1. Engage the claw and install the 2 front wiper arm head caps.



55. TEMPORARILY TIGHTEN HOOD SUB-ASSEMBLY
  1. Provisionally install the hood with the 4 bolts.

    HINT:
    Tighten the bolts to the specified torque after inspecting the hood.



56. INSPECT HOOD SUB-ASSEMBLY


  1. Check that the clearance measurements are within the standard ranges.


    B140679E01


    Standard:

    Area
    Measurement
    Area
    Measurement
    A
    2.35 to 6.35 mm
    (0.092 to 0.250 in.)
    C
    2.0 to 5.0 mm
    (0.079 to 0.197 in.)
    B
    -2 to 2 mm
    (-0.079 to 0.079 in.)
    -
    -



57. ADJUST HOOD SUB-ASSEMBLY


    B136202
  1. Loosen the hood side hinge bolts.

  1. Move the hood to adjust the clearance to within the standard range.

  1. Tighten the hood side hinge bolts after the adjustment.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }



    B136203
  1. Adjust the height of the hood front end by turning the cushion rubber.

    HINT:
    The cushion rubber can be raised and lowered by turning it.



    B136204
  1. Adjust the hood lock.

    1. Loosen the 3 bolts.

    2. Adjust the hood lock position so that the striker can enter it smoothly.

    3. Tighten the 3 bolts after the adjustment.

      Torque:
      7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



58. INSTALL FRONT WHEELS

Torque:
103 N*m{ 1050 kgf*cm , 76 ft.*lbf }



59. INSTALL NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY


    C139112E02
  1. Install clip B onto the body portion and install No. 1 steering column hole cover onto the body portion with clip A.
    Text in Illustration 
    *1
    Clip A
    *2
    Clip B

    NOTICE:
    Make sure that the lip portion of No. 1 steering column hole cover is not damaged.



60. INSTALL STEERING SLIDING YOKE SUB-ASSEMBLY


C118005E08
  1. Align the matchmarks and install the sliding yoke onto the intermediate shaft with bolt B.
    Text in Illustration 
    *1
    Bolt A
    *2
    Bolt B
    *a
    Matchmark

    Torque:
    35 N*m{ 360 kgf*cm , 26 ft.*lbf }

  1. Tighten bolt A.

    Torque:
    35 N*m{ 360 kgf*cm , 26 ft.*lbf }



61. INSTALL COLUMN HOLE COVER SILENCER SHEET
  1. Install the column hole cover silencer sheet with the 2 clips.

  1. Install the floor carpet.



62. INSTALL BATTERY TRAY


63. INSTALL BATTERY
  1. Install the battery onto the vehicle with the battery clamp.

    Torque:
    3.5 N*m{ 36 kgf*cm , 31 in.*lbf }

  1. Connect the cable to the battery terminal.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



64. ADD AUTOMATIC TRANSAXLE FLUID

Automatic transaxle fluid type:
Toyota Genuine ATF WS

Automatic Transaxle Fluid Capacity (Reference) 
Drain and refill
2.5 liters (2.6 US qts, 2.2 Imp. qts)
Dry fill
6.4 liters (6.8 US qts, 5.6 Imp. qts)


65. INSPECT AUTOMATIC TRANSAXLE FLUID LEVEL


D025120E03

HINT:
Drive the vehicle until the engine and transaxle are at normal operating temperature.

Fluid temperature:
70 to 80 °C (158 to 176 °F)

  1. Park the vehicle on a level surface and engage the parking brake.

  1. With the engine idling and the brake pedal depressed, shift the shift lever into all positions from P to L, and then return it to the P position.

  1. Pull out the oil level gauge and wipe it clean.

  1. Push it fully back into the pipe.

  1. Pull it out and check that the fluid level is within the HOT range.
    If there is any leakage, repair or replace O-rings, FIPGs, oil seals, plugs or other parts.



66. INSPECT FOR AUTOMATIC TRANSAXLE FLUID LEAK


67. INSPECT SHIFT LEVER POSITION
  1. When shifting the lever from P to the R position with the ignition switch on (IG) and the brake pedal depressed, make sure that the shift lever moves smoothly and moves correctly into position.

  1. Start the engine and make sure that the vehicle moves forward when shifting the lever from N to the D position and moves rearward when shifting the lever to the R position.
    If the operation cannot be performed as specified, inspect the park/neutral position switch assembly and check the shift lever assembly installation condition.



68. ADJUST SHIFT LEVER POSITION
  1. Shift the shift lever to the N position.



    C117121E01
  1. Slide the adjuster case cover in the direction shown in the illustration and pull out the lock piece.

  1. Gently pull the cable rod toward the rear of the vehicle by hand to pull the cable taut.



    C117120E01
  1. Press the lock piece into the adjuster case and lock it.



    C117119E01
  1. Slide the cover in the direction shown in the illustration.

    NOTICE:
    Slide the cover past the protrusion of the lock piece.

  1. Inspect the operation after the adjustment.



69. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT
  1. Inspect and adjust the front wheel alignment (Click here).



70. INSTALL ENGINE UNDER COVER RH

Torque:
5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



71. INSTALL ENGINE UNDER COVER LH

Torque:
5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



72. CHECK ABS SENSOR SIGNAL
  1. Check the ABS sensor signal (Click here).



73. RESET MEMORY (AT initialization)
  1. Perform Reset Memory (AT initialization) when replacing the automatic transaxle assembly (Click here).