Home › TRANSMISSION ยท U441E AUTOMATIC TRANSAXLE › AUTOMATIC TRANSAXLE ASSEMBLY (for Sedan)

AUTOMATIC TRANSAXLE ASSEMBLY (for Sedan) > REMOVAL

for Preparation Click here



1. POSITION FRONT WHEELS FACING STRAIGHT AHEAD


2. REMOVE BATTERY
  1. Disconnect the cable from the battery terminal.

  1. Loosen the nut and remove the battery clamp.

  1. Remove the battery.



3. REMOVE BATTERY TRAY


4. REMOVE COLUMN HOLE COVER SILENCER SHEET


    A116501E01
  1. Remove the floor carpet and 2 clips and remove the column hole cover silencer.



5. SEPARATE STEERING SLIDING YOKE SUB-ASSEMBLY


    C139107
  1. Use a seat belt to fix the steering wheel assembly, in order to avoid breakage of the spiral cable.



    C118005E08
  1. Place matchmarks on the sliding yoke of the steering intermediate shaft assembly and the steering gear assembly.
    Text in Illustration 
    *1
    Bolt A
    *2
    Bolt B
    *a
    Matchmark

  1. Loosen bolt A, remove bolt B and separate the steering intermediate shaft assembly.



6. SEPARATE NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY


C139112E02
  1. Remove clip A, separate clip B from the body and separate No. 1 steering column hole cover.
    Text in Illustration 
    *1
    Clip A
    *2
    Clip B

    NOTICE:
    Do not damage clip B.



7. REMOVE FRONT WHEELS


8. REMOVE ENGINE UNDER COVER LH


9. REMOVE ENGINE UNDER COVER RH


10. DRAIN AUTOMATIC TRANSAXLE FLUID
  1. Remove the drain plug and gasket, and drain the ATF.

  1. Install a new gasket and the drain plug.

    Torque:
    17 N*m{ 175 kgf*cm , 13 ft.*lbf }



11. REMOVE HOOD SUB-ASSEMBLY
  1. Remove the 4 bolts and remove the hood.



12. REMOVE FRONT WIPER ARM HEAD CAP


    E127832E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the claw and remove the 2 front wiper arm head caps.



13. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH


    E127833
  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.

  1. Remove the nut and front wiper arm.



14. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



15. REMOVE COWL SIDE VENTILATOR SUB-ASSEMBLY LH


    E127834E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 3 claws and remove the cowl side ventilator sub-assembly LH.



16. REMOVE COWL SIDE VENTILATOR SUB-ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



17. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for LHD)


    E127838
  1. Disengage the 3 clips, the 4 claws and the 8 hooks.

  1. Remove the cowl top ventilator louver sub-assembly.



    E127839
  1. Disconnect the washer hoses.

  1. Disengage the 5 hooks.



18. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for RHD)


    E127835
  1. Disengage the 2 clips, the 6 claws and the 10 hooks.

  1. Remove the cowl top ventilator louver sub-assembly.



    E127836
  1. Disconnect the washer hoses.

  1. Disengage the 5 hooks.



19. REMOVE FRONT WIPER MOTOR AND LINK


    E127837
  1. Remove the 2 bolts.

  1. Slide the wiper link. Disengage the meshing of the rubber pin, then disconnect the connector and remove the front wiper motor and link.



20. REMOVE FRONT AIR SHUTTER SEAL (for LHD)


A133324
  1. Disengage the 3 claws and remove the front air shutter seal.



21. REMOVE FRONT AIR SHUTTER SEAL (for RHD)


A133324
  1. Disengage the 3 claws and remove the front air shutter seal.



22. REMOVE OUTER COWL TOP PANEL (for LHD)


A128446
  1. Disengage the wire harness clamp.



    A128447
  1. Remove the 2 bolts and remove the cowl top to cowl inner brace.



    A128448
  1. Remove the 8 bolts and remove the cowl top panel outer.



23. REMOVE OUTER COWL TOP PANEL (for RHD)


A128446
  1. Disengage the wire harness clamp.



    A128447
  1. Remove the 2 bolts and remove the cowl top to cowl inner brace.



    A128448
  1. Remove the 8 bolts and remove the cowl top panel outer.



24. REMOVE NO. 2 CYLINDER HEAD COVER


A116235
  1. Remove the 4 nuts and cylinder head cover No. 2.



25. REMOVE AIR CLEANER ASSEMBLY


A117355
  1. Separate the intake air flow meter connector and wire harness clamp.

  1. Separate the fuel vapor feed hose and fuel vapor feed hose No. 1 from the vacuum switching valve assembly.

  1. Separate the vacuum switching valve connector and wire harness clamp.

  1. Separate the ventilation hose from the air cleaner hose.

  1. Release the air cleaner cap sub-assembly with air cleaner hose No. 1.

  1. Loosen the air cleaner hose clamp on the throttle body side and remove the air cleaner cap and air cleaner hose.

  1. Remove the air cleaner element.



    A104895
  1. Separate the wire harness clamp from the air cleaner case.

  1. Remove the 2 bolts and remove the air cleaner case with air cleaner inlet No. 1.



26. REMOVE AIR CLEANER BRACKET


A117308
  1. Separate the wire harness clamp from the air cleaner bracket.

  1. Remove the 2 bolts and remove the air cleaner bracket.



27. REMOVE BATTERY CARRIER


A117309
  1. Separate the wire harness clamp from the battery carrier.

  1. Remove the 5 bolts and remove the battery carrier.



28. SEPARATE TRANSMISSION CONTROL CABLE ASSEMBLY


C107765
  1. Remove the nut and disconnect the control cable from the control shaft lever.

  1. Remove the clip and disconnect the control cable from the control cable bracket.



29. SEPARATE NO. 3 ENGINE WIRE


    A166735E01
  1. Remove the bolt and separate the No. 3 engine wire from the automatic transaxle.

  1. Separate the 2 clamps from the engine mount insulator.



30. DISCONNECT CONNECTORS
  1. Separate the park/neutral position switch connector.

  1. Separate the transmission wire connector.

  1. Separate the transmission revolution sensor connector.

  1. w/o ABS:

    1. Separate the speedometer sensor connector.



31. DISCONNECT WIRE HARNESS


    C107772
  1. Remove the 2 bolts and separate the 2 wire harness clamp brackets from the automatic transaxle.



    C107771
  1. Remove the bolt and separate the wire harness clamp bracket from the automatic transaxle



32. REMOVE STARTER ASSEMBLY


A104498
  1. Remove the terminal cap.

  1. Remove the nut and disconnect terminal 30.

  1. Disconnect the connector.

  1. Remove the 2 bolts and remove the starter assembly.



33. REMOVE FRONT AXLE HUB NUT LH


C085629E02
  1. Using SST and a hammer, release the staked part of the axle hub nut.

    SST
    09930-00010  

    NOTICE:
    1. Insert SST into the groove with the flat surface facing up.
    2. Do not damage the tip of SST using grinders.
    3. Completely unstake the staked part before removing the axle hub nut.
    4. Do not damage the threads of the drive shaft.

  1. Using a 30 mm socket wrench, remove the axle hub nut.



34. REMOVE FRONT AXLE HUB NUT RH

HINT:
Use the same procedure for the LH side and RH side.



35. SEPARATE FRONT SPEED SENSOR LH (w/ ABS)


C125274
  1. Remove the bolt and separate the speed sensor and flexible hose.



    C112274
  1. Remove the bolt and separate the speed sensor from the steering knuckle.

    NOTICE:
    1. Keep the speed sensor tip and installation portion free of foreign matter.
    2. Remove the speed sensor without turning it from its original installation angle.



36. SEPARATE FRONT SPEED SENSOR RH (w/ ABS)

HINT:
Use the same procedure for the LH side and RH side.



37. SEPARATE FRONT FLEXIBLE HOSE LH (w/o ABS)


C186418
  1. Remove the bolt and separate the flexible hose.



38. SEPARATE FRONT FLEXIBLE HOSE RH (w/o ABS)

HINT:
Use the same procedure for the LH side and RH side.



39. SEPARATE FRONT STABILIZER LINK ASSEMBLY LH


C106044
  1. Remove the nut and separate the stabilizer link from the shock absorber.

    HINT:
    If the ball joint turns together with the nut, use a socket hexagon wrench 6 to hold the stud.



40. SEPARATE FRONT STABILIZER LINK ASSEMBLY RH

HINT:
Use the same procedure for the LH side and RH side.



41. SEPARATE TIE ROD END SUB-ASSEMBLY LH
  1. Remove the cotter pin and castle nut.



    C172757E01
  1. Install SST (spacer B) to the threaded section of the tie rod end.

    SST
    09960-20010   (09961-02060)

    NOTICE:
    Make sure the upper ends of the threaded section of the tie rod end and SST (spacer B) are aligned.



  1. Using SST, separate the tie rod end from the front axle assembly.


    C172758E01

    SST
    09960-20010   (09961-02010)

    NOTICE:
    1. Make sure to tie the string of SST to the vehicle to prevent SST from dropping.
    2. Install SST so that A and B are parallel.
    3. Be sure to place the wrench on the part indicated in the illustration.
    4. Do not damage the ball joint dust cover.
    5. Do not damage the front disc brake dust cover.



42. SEPARATE TIE ROD END SUB-ASSEMBLY RH

HINT:
Use the same procedure for the LH side and RH side.



43. SEPARATE FRONT SUSPENSION LOWER ARM LH


C107513
  1. Remove the clip and castle nut.



    C172759E01
  1. Install SST (spacer B) to the threaded section of the lower ball joint.

    SST
    09960-20010   (09961-02060)

    NOTICE:
    Make sure the upper ends of the threaded section of the lower ball joint and SST (spacer B) are aligned.



  1. Using SST, separate the front lower suspension arm from the front axle assembly.


    C172760

    SST
    09960-20010   (09961-02010)

    NOTICE:
    1. Make sure to tie the string of SST to the vehicle to prevent SST from dropping.
    2. Install SST so that A and B are parallel.
    3. Be sure to place the wrench on the part indicated in the illustration.
    4. Do not damage the lower ball joint dust cover.
    5. Do not damage the drive shaft outboard joint boots.
    6. Do not damage the front disc brake dust cover.



44. SEPARATE FRONT SUSPENSION LOWER ARM RH

HINT:
Use the same procedure for the LH side and RH side.



45. SEPARATE FRONT AXLE ASSEMBLY LH
  1. Using a plastic hammer, tap the end of the drive shaft and disengage the fitting between the drive shaft and front axle.

    HINT:
    If it is difficult to disengage the fitting, tap the end of the drive shaft with a brass bar and hammer.

  1. Push the front axle out of the vehicle to remove the drive shaft from the front axle.

    NOTICE:
    1. Do not push the front axle further out of the vehicle than is necessary.
    2. Do not damage the outboard joint boot.
    3. Do not damage the speed sensor rotor.
    4. Suspend the drive shaft with a piece of string or the equivalent.



46. SEPARATE FRONT AXLE ASSEMBLY RH

HINT:
Use the same procedure for the LH side and RH side.



47. REMOVE AUTOMATIC TRANSMISSION CASE PROTECTOR (w/o ABS)


    C121812
  1. Remove the 2 bolts and automatic transmission case protector.



48. REMOVE FRONT DRIVE SHAFT ASSEMBLY LH


C107924
  1. Using SST, remove the drive shaft.

    SST
    09520-01010  
    09520-24010   (09520-32040)

    NOTICE:
    1. Do not damage the oil seal.
    2. Do not damage the inboard joint boot.
    3. Do not drop the drive shaft.



49. REMOVE FRONT DRIVE SHAFT ASSEMBLY RH


C116896
  1. Using a screwdriver and hammer, remove the drive shaft.

    NOTICE:
    1. Do not damage the oil seal.
    2. Do not damage the inboard joint boot.
    3. Do not drop the drive shaft.



50. SUSPEND ENGINE ASSEMBLY


  1. 1NZ-FE, 2NZ-FE

    1. Remove the bolt and remove the radio setting condenser.

    2. Remove the bolt and remove the air-fuel ratio sensor wiring bracket.



    3. A070012E02
    4. Install the engine hanger with the bolt in the position shown in the illustration.
      Text in Illustration 
      *a
      Front
      *b
      Rear
      Part No. 
      Engine hanger
      12281-21010
      Bolt
      91642-81025

      Torque:
      40 N*m{ 408 kgf*cm , 30 ft.*lbf }

    5. Using an engine sling device and a chain block, support the engine assembly w/transaxle and front suspension crossmember.



51. SEPARATE OIL COOLER HOSE


    C118497
  1. Separate the inlet oil cooler hose from inlet No. 1 oil cooler tube.

  1. Separate the outlet oil cooler hose from outlet No. 1 oil cooler tube.



52. REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY


    C107979E01
  1. Remove the bolt and separate the engine moving control rod.

  1. Support the front suspension crossmember with a transmission jack.



    C107982
  1. Remove the 6 bolts and remove the suspension crossmember.



53. REMOVE NO. 2 ENGINE MOVING CONTROL ROD


C118499E01
  1. Remove the 3 bolts and remove the No. 2 engine moving control rod.



54. SUPPORT AUTOMATIC TRANSAXLE ASSEMBLY
  1. Support the automatic transaxle with the transmission jack.



55. REMOVE ENGINE MOUNTING INSULATOR LH


    C159390
  1. Remove the bolt and nut and separate the engine mounting insulator LH from the engine mounting bracket LH.



    C159389
  1. Remove 5 bolts and remove the engine mounting insulator LH.



56. REMOVE ENGINE MOUNTING BRACKET LH


    C181848
  1. Remove the 4 bolts and remove the engine mounting bracket LH from the automatic transaxle.



57. REMOVE AUTOMATIC TRANSAXLE ASSEMBLY


    C118502
  1. Remove the flywheel housing under cover.



    C118503
  1. Remove the 6 torque converter set bolts while holding the crankshaft pulley bolt with a wrench.



    C080982
  1. Remove the 7 bolts and remove the automatic transaxle from the engine.



58. REMOVE TORQUE CONVERTER ASSEMBLY
  1. Remove the torque converter from the automatic transaxle.



59. REMOVE SPEEDOMETER DRIVEN HOLE COVER SUB-ASSEMBLY (w/ ABS)


    C193438E01
  1. Remove the bolt and remove the speedometer driven hole cover.

  1. Remove the O-ring from the speedometer driven hole cover.



60. REMOVE SPEEDOMETER SENSOR (w/o ABS)


    C186726
  1. Disconnect the speedometer sensor connector.

  1. Remove the bolt and speedometer sensor.



61. REMOVE SPEEDOMETER DRIVEN GEAR (w/o ABS)


    C117097E02
  1. Remove the clip and driven gear from the speedometer sensor.

  1. Remove the O-ring from the speedometer sensor.



62. REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET


    C107779
  1. Remove the 2 bolts and remove No. 1 transmission control cable bracket from the automatic transaxle.



63. SEPARATE INLET NO. 1 OIL COOLER TUBE


    C181839E01
  1. Using a union nut wrench, separate the inlet No. 1 oil cooler tube while holding the oil cooler tube union with a wrench.



64. SEPARATE OUTLET NO. 1 OIL COOLER TUBE


    C181837E01
  1. Using a union nut wrench, separate the outlet No. 1 oil cooler tube while holding the oil cooler tube union with a wrench.



65. REMOVE NO. 1 OIL COOLER TUBE CLAMP


    C123300E01
  1. Remove the bolt and remove No. 1 oil cooler tube clamp from the oil filler tube.

  1. Remove the inlet No. 1 oil cooler tube and the outlet No. 1 oil cooler tube from the automatic transaxle.



66. REMOVE TRANSMISSION OIL LEVEL GAUGE SUB-ASSEMBLY
  1. Remove the oil level gauge from the oil filler tube.



67. REMOVE TRANSMISSION OIL FILLER TUBE SUB-ASSEMBLY


C107781
  1. Remove the bolt and remove the oil filler tube.

  1. Remove the O-ring from the oil filler tube.



68. INSPECT TORQUE CONVERTER AND DRIVE PLATE
  1. Inspect the torque converter and drive plate (Click here).