Home › SUSPENSION & AXLE › SUSPENSION › FRONT LOWER SUSPENSION ARM (for 1NZ-FE RH Side, 2NZ-FE RH Side)

FRONT LOWER SUSPENSION ARM (for 1NZ-FE RH Side, 2NZ-FE RH Side) > INSTALLATION

for Preparation Click here



1. TEMPORARILY TIGHTEN FRONT SUSPENSION LOWER ARM RH
  1. Install the lower arm onto the crossmember and provisionally tighten the bolt.



2. INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY
  1. Support the front suspension crossmember with a transmission jack.



    A108973E07
  1. Provisionally install the front suspension crossmember onto the body with the 6 bolts.
    Text in Illustration 
    *1
    Bolt A
    *2
    Bolt B
    *3
    Bolt C
    *a
    Front Side
    Bolt
    Underhead Length (mm)
    A
    38
    B
    99
    C
    41



  1. By inserting SST into the datum holes in the front suspension crossmembers RH and LH alternately, tighten bolts A, B and C on both sides to the specified torque, in several steps.


    C230201E01


    Text in Illustration 
    *1
    Bolt A
    *2
    Bolt B
    *3
    Bolt C
    *4
    for Bolt B with Bolt Strength Class 11T
    *5
    for Bolt B with Bolt Strength Class 10T
    -
    -
    *a
    Front Side
    *b
    Datum Hole
    *c
    OK
    *d
    NG
    SST
    09670-00011  

    Torque:
    Bolt A:
    87 N*m{ 887 kgf*cm , 64 ft.*lbf }
    Bolt B with Bolt Strength Class 11T:
    160 N*m{ 1631 kgf*cm , 118 ft.*lbf }
    Bolt B with Bolt Strength Class 10T:
    151 N*m{ 1540 kgf*cm , 111 ft.*lbf }
    Bolt C:
    98 N*m{ 999 kgf*cm , 72 ft.*lbf }

    NOTICE:
    1. Insert SST into the datum hole in a vertical orientation.
    2. If SST cannot be inserted into the datum hole vertically, loosen all the bolts and then insert SST again.

  1. Install the engine moving control rod with the bolt.

    Torque:
    120 N*m{ 1224 kgf*cm , 89 ft.*lbf }



3. INSTALL FRONT STABILIZER LINK ASSEMBLY LH


    C106044
  1. Install the stabilizer link with the nut.

    Torque:
    74 N*m{ 755 kgf*cm , 55 ft.*lbf }

    HINT:
    If the ball joint turns together with the nut, use a socket hexagon wrench 6 to hold the stud.



4. INSTALL FRONT STABILIZER LINK ASSEMBLY RH

HINT:
The installation procedure for the RH side is the same as that for the LH side.



5. INSTALL FRONT SUSPENSION LOWER ARM LH


    C107513
  1. Install the lower arm onto the steering knuckle with a new castle nut.

    Torque:
    98 N*m{ 1000 kgf*cm , 72 ft.*lbf }

    NOTICE:
    If the holes for the clip are not aligned, tighten the nut by a further turn of up to 60°.

  1. Install a new clip.



6. INSTALL FRONT SUSPENSION LOWER ARM RH

HINT:
The installation procedure for the RH side is the same as that for the LH side.



7. INSTALL TIE ROD END SUB-ASSEMBLY LH


    C107961
  1. Install the tie rod end onto the steering knuckle with a new castle nut.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }

    NOTICE:
    If the holes for the clip are not aligned, tighten the nut by a further turn of up to 60°.

  1. Install a new cotter pin.



8. INSTALL TIE ROD END SUB-ASSEMBLY RH

HINT:
The installation procedure for the RH side is the same as that for the LH side.



9. INSTALL STEERING COLUMN HOLE COVER SUB-ASSEMBLY


    C139112E02
  1. Install clip B onto the body portion and install No. 1 steering column hole cover onto the body portion with clip A.
    Text in Illustration 
    *1
    Clip A
    *2
    Clip B

    NOTICE:
    Make sure that the lip portion of No. 1 steering column hole cover is not damaged.



10. INSTALL STEERING SLIDING YOKE SUB-ASSEMBLY


C118005E08
  1. Align the matchmarks and install the sliding yoke onto the intermediate shaft with bolt B.
    Text in Illustration 
    *1
    Bolt A
    *2
    Bolt B
    *a
    Matchmark

    Torque:
    35 N*m{ 360 kgf*cm , 26 ft.*lbf }

  1. Tighten bolt A.

    Torque:
    35 N*m{ 360 kgf*cm , 26 ft.*lbf }



11. INSTALL COLUMN HOLE COVER SILENCER SHEET
  1. Install the column hole cover silencer sheet with the 2 clips.

  1. Install the floor carpet.



12. INSTALL FRONT WHEEL

Torque:
103 N*m{ 1050 kgf*cm , 76 ft.*lbf }



13. POSITION WHEELS FACING STRAIGHT AHEAD


14. STABILIZE SUSPENSION
  1. Lower the vehicle from the jack.

  1. Bounce the vehicle up and down several times to stabilize the suspension.



15. FULLY TIGHTEN FRONT SUSPENSION LOWER ARM RH


C230703E01
  1. Fully tighten the 2 bolts.
    Text in Illustration 
    *1
    for Bolt B with Bolt Strength Class 11T
    *2
    for Bolt B with Bolt Strength Class 10T

    Torque:
    Bolt A:
    137 N*m{ 1397 kgf*cm , 101 ft.*lbf }
    Bolt B with Bolt Strength Class 11T:
    160 N*m{ 1631 kgf*cm , 118 ft.*lbf }
    Bolt B with Bolt Strength Class 10T:
    151 N*m{ 1540 kgf*cm , 111 ft.*lbf }



16. INSTALL COWL TOP PANEL OUTER (for Hatchback)


A115392
  1. Install the cowl top panel with the 9 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 57 in.*lbf }



    A108438
  1. Connect the wire harness clamp.



17. INSTALL NO. 2 COWL TO REGISTER DUCT SUB-ASSEMBLY (for Hatchback)


A108437
  1. Engage the claw to install cowl to register duct No. 2.



18. INSTALL FRONT WIPER MOTOR AND LINK (for Hatchback)


E113861
  1. Connect the connector.

  1. Slide the wiper link as shown in the illustration and engage the rubber pin with the body.

  1. Install the front wiper motor and link with the 2 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



19. INSTALL COWL TOP VENTILATOR LOUVER LH (for Hatchback LHD)


E113853
  1. Engage the 4 claws and install the cowl top ventilator louver LH.

  1. Install the 2 clips.



20. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for Hatchback LHD)


E113854
  1. Connect the washer hose.



    E113852
  1. Engage the 11 claws and install the cowl top ventilator louver sub-assembly.

  1. Install the clip.

  1. Connect the washer hose.



    E117641
  1. Engage the 2 hooks and install cowl top ventilator louver center No. 1.



21. INSTALL COWL TOP VENTILATOR LOUVER LH (for Hatchback RHD)


E113856
  1. Engage the 4 claws and install the cowl top ventilator louver LH.

  1. Install the clip.



22. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for Hatchback RHD)


E113855
  1. Engage the 10 claws and install the cowl top ventilator louver sub-assembly.

  1. Install the clip.

  1. Connect the washer hose.



23. INSTALL HOOD TO COWL TOP SEAL (for Hatchback)


E113851
  1. Engage the 7 clips and install the hood to cowl top seal.



24. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH (for Hatchback)


E058837E10
  1. Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.



    E113862E01
  1. Align the blade tip with the mark on the windshield glass, as shown in the illustration.

  1. Tighten the nut of the front wiper arm.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }



25. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH (for Hatchback)


E058837E10
  1. Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.



    E113863E01
  1. Align the blade tip with the mark on the windshield glass, as shown in the illustration.

  1. Tighten the nut of the front wiper arm.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }



26. INSTALL FRONT WIPER ARM HEAD CAP (for Hatchback)


E113849
  1. Engage the claw and install the 2 front wiper arm head caps.



27. INSTALL COWL TOP PANEL OUTER (for Sedan)


A128448
  1. Install the cowl top panel outer with the 8 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 57 in.*lbf }



    A128447
  1. Install the cowl top to cowl inner brace with the 2 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 57 in.*lbf }



    A128446
  1. Connect the wire harness clamp.



28. INSTALL FRONT AIR SHUTTER SEAL (for Sedan)


A133324
  1. Engage the 3 claws to install the front air shutter seal.



29. INSTALL FRONT WIPER MOTOR AND LINK (for Sedan)


    E127840
  1. Connect the connector.

  1. Slide the wiper link as shown in the illustration and engage the rubber pin with the body.

  1. Install the front wiper motor and link with the 2 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



30. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for Sedan LHD)


    E127839
  1. Connect the washer hoses.

  1. Engage the 5 hooks.



    E127838
  1. Engage the 8 hooks and the 4 claws.

  1. Install the cowl top ventilator louver sub-assembly with the 3 clips.



31. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for Sedan RHD)


    E127836
  1. Connect the washer hoses.

  1. Engage the 5 hooks.



    E127835
  1. Engage the 10 hooks and the 6 claws.

  1. Install the cowl top ventilator louver sub-assembly with the 2 clips.



32. INSTALL COWL SIDE VENTILATOR SUB-ASSEMBLY LH (for Sedan)


    E129651
  1. Engage the 3 claws and install the cowl side ventilator sub-assembly LH.



33. INSTALL COWL SIDE VENTILATOR SUB-ASSEMBLY RH (for Sedan)

HINT:
Use the same procedure as for the LH side.



34. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH (for Sedan)


    E058837E10
  1. Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.



    E113862E01
  1. Align the blade tip with the mark on the windshield glass, as shown in the illustration.

  1. Tighten the nut of the front wiper arm.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }



35. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH (for Sedan)


    E058837E10
  1. Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.



    E129694E01
  1. Align the blade tip with the mark on the windshield glass, as shown in the illustration.

  1. Tighten the nut of the front wiper arm.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }



36. INSTALL FRONT WIPER ARM HEAD CAP (for Sedan)


    E127841
  1. Engage the claw and install the 2 front wiper arm head caps.



37. INSPECT HOOD SUB-ASSEMBLY (for Hatchback)


  1. Check that the clearance measurements are within the standard ranges.


    B118065E01


    Standard:

    Area
    Measurement
    Area
    Measurement
    A
    1.7 to 5.7 mm
    (0.067 to 0.224 in.)
    G
    -1.55 to 2.45 mm
    (-0.061 to 0.096 in.)
    B
    -2 to 2 mm
    (-0.079 to 0.079 in.)
    H
    1.75 to 5.75 mm
    (0.067 to 0.226 in.)
    C
    4.45 to 10.45 mm
    (0.175 to 0.411 in.)
    I
    -1.25 to 2.75 mm
    (-0.049 to 0.108 in.)
    D
    -0.95 to 5.05 mm
    (-0.037 to 0.199 in.)
    J
    -1.5 to 1.5 mm
    (-0.059 to 0.059 in.)
    E
    7.55 to 13.55 mm
    (0.297 to 0.533 in.)
    K
    2.0 to 5.0 mm
    (0.079 to 0.197 in.)
    F
    1.65 to 5.65 mm
    (0.065 to 0.222 in.)
    -
    -



38. ADJUST HOOD SUB-ASSEMBLY (for Hatchback)


    B106963
  1. Loosen the hood side hinge bolts.

  1. Move the hood to adjust the clearance to within the standard range.

  1. Tighten the hood side hinge bolts after the adjustment.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }



    B106965
  1. Adjust the height of the hood front end by turning the cushion rubber.

    HINT:
    The cushion rubber can be raised and lowered by turning it.



    B106964
  1. Adjust the hood lock.

    1. Loosen the 3 bolts.

    2. Adjust the hood lock position so that the striker can enter it smoothly.

    3. Tighten the 3 bolts after the adjustment.

      Torque:
      7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



39. INSPECT HOOD SUB-ASSEMBLY (for Sedan)


  1. Check that the clearance measurements are within the standard ranges.


    B140679E01


    Standard:

    Area
    Measurement
    Area
    Measurement
    A
    2.35 to 6.35 mm
    (0.092 to 0.250 in.)
    C
    2.0 to 5.0 mm
    (0.079 to 0.197 in.)
    B
    -2 to 2 mm
    (-0.079 to 0.079 in.)
    -
    -



40. ADJUST HOOD SUB-ASSEMBLY (for Sedan)


    B136202
  1. Loosen the hood side hinge bolts.

  1. Move the hood to adjust the clearance to within the standard range.

  1. Tighten the hood side hinge bolts after the adjustment.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }



    B136203
  1. Adjust the height of the hood front end by turning the cushion rubber.

    HINT:
    The cushion rubber can be raised and lowered by turning it.



    B136204
  1. Adjust the hood lock.

    1. Loosen the 3 bolts.

    2. Adjust the hood lock position so that the striker can enter it smoothly.

    3. Tighten the 3 bolts after the adjustment.

      Torque:
      7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



41. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT (for Hatchback)
(Click here)


42. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT (for Sedan)
(Click here)