Home › SUSPENSION & AXLE › SUSPENSION › FRONT STABILIZER BAR (for Hatchback)

FRONT STABILIZER BAR (for Hatchback) > INSTALLATION

for Preparation Click here



1. INSTALL FRONT STABILIZER BAR BUSH


C107520E03
  1. Install the stabilizer bar bush onto the stabilizer bar.

    HINT:
    1. Install the bush onto the stabilizer so that the bush stopper of the stabilizer bar faces the outside of the vehicle.
    2. Install the bush with its cutout facing the front of the vehicle.



2. INSTALL FRONT STABILIZER BAR


C107521E01
  1. Install the stabilizer onto the crossmember with the paint mark on the left side of the vehicle.



3. INSTALL FRONT STABILIZER BRACKET LH


C116871E01
  1. Provisionally tighten bolt A.

  1. Tighten the bolts to the specified torque, in the order of B then A.

    Torque:
    47 N*m{ 479 kgf*cm , 35 ft.*lbf }



4. INSTALL FRONT STABILIZER BRACKET RH

HINT:
The installation procedure for the RH side is the same as that for the LH side.



5. INSTALL POWER STEERING GEAR
  1. Install the steering gear assembly onto the front suspension crossmember with the 2 bolts and 2 nuts.

    Torque:
    96 N*m{ 979 kgf*cm , 71 ft.*lbf }

    NOTICE:
    Keep the nut from rotating while turning the bolt.



6. INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY
  1. Support the front suspension crossmember with a transmission jack.



    A108973E07
  1. Provisionally install the front suspension crossmember onto the body with the 6 bolts.
    Text in Illustration 
    *1
    Bolt A
    *2
    Bolt B
    *3
    Bolt C
    *a
    Front Side
    Bolt
    Underhead Length (mm)
    A
    38
    B
    99
    C
    41



  1. By inserting SST into the datum holes in the front suspension crossmembers RH and LH alternately, tighten bolts A, B and C on both sides to the specified torque, in several steps.


    C230201E01


    Text in Illustration 
    *1
    Bolt A
    *2
    Bolt B
    *3
    Bolt C
    *4
    for Bolt B with Bolt Strength Class 11T
    *5
    for Bolt B with Bolt Strength Class 10T
    -
    -
    *a
    Front Side
    *b
    Datum Hole
    *c
    OK
    *d
    NG
    SST
    09670-00011  

    Torque:
    Bolt A:
    87 N*m{ 887 kgf*cm , 64 ft.*lbf }
    Bolt B with Bolt Strength Class 11T:
    160 N*m{ 1631 kgf*cm , 118 ft.*lbf }
    Bolt B with Bolt Strength Class 10T:
    151 N*m{ 1540 kgf*cm , 111 ft.*lbf }
    Bolt C:
    98 N*m{ 999 kgf*cm , 72 ft.*lbf }

    NOTICE:
    1. Insert SST into the datum hole in a vertical orientation.
    2. If SST cannot be inserted into the datum hole vertically, loosen all the bolts and then insert SST again.

  1. Install the engine moving control rod with the bolt.

    Torque:
    120 N*m{ 1224 kgf*cm , 89 ft.*lbf }



7. INSTALL FRONT STABILIZER LINK ASSEMBLY LH
  1. Install the stabilizer link with the 2 nuts.

    Torque:
    74 N*m{ 755 kgf*cm , 55 ft.*lbf }

    HINT:
    If the ball joint turns together with the nut, use a socket hexagon wrench 6 to hold the stud.



8. INSTALL FRONT STABILIZER LINK ASSEMBLY RH

HINT:
The installation procedure for the RH side is the same as that for the LH side.



9. INSTALL FRONT SUSPENSION LOWER ARM LH


    C107513
  1. Install the lower arm onto the steering knuckle with a new castle nut.

    Torque:
    98 N*m{ 1000 kgf*cm , 72 ft.*lbf }

    NOTICE:
    If the holes for the clip are not aligned, tighten the nut by a further turn of up to 60°.

  1. Install a new clip.



10. INSTALL FRONT SUSPENSION LOWER ARM RH

HINT:
The installation procedure for the RH side is the same as that for the LH side.



11. INSTALL TIE ROD END SUB-ASSEMBLY LH


    C107961
  1. Install the tie rod end onto the steering knuckle with a new castle nut.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }

    NOTICE:
    If the holes for the clip are not aligned, tighten the nut by a further turn of up to 60°.

  1. Install a new cotter pin.



12. INSTALL TIE ROD END SUB-ASSEMBLY RH

HINT:
The installation procedure for the RH side is the same as that for the LH side.



13. INSTALL STEERING COLUMN HOLE COVER SUB-ASSEMBLY


    C139112E02
  1. Install clip B onto the body portion and install No. 1 steering column hole cover onto the body portion with clip A.
    Text in Illustration 
    *1
    Clip A
    *2
    Clip B

    NOTICE:
    Make sure that the lip portion of No. 1 steering column hole cover is not damaged.



14. INSTALL STEERING SLIDING YOKE SUB-ASSEMBLY


C118005E08
  1. Align the matchmarks and install the sliding yoke onto the intermediate shaft with bolt B.
    Text in Illustration 
    *1
    Bolt A
    *2
    Bolt B
    *a
    Matchmark

    Torque:
    35 N*m{ 360 kgf*cm , 26 ft.*lbf }

  1. Tighten bolt A.

    Torque:
    35 N*m{ 360 kgf*cm , 26 ft.*lbf }



15. INSTALL COLUMN HOLE COVER SILENCER SHEET
  1. Install the column hole cover silencer sheet with the 2 clips.

  1. Install the floor carpet.



16. INSTALL FRONT WHEEL

Torque:
103 N*m{ 1050 kgf*cm , 76 ft.*lbf }



17. POSITION WHEELS FACING STRAIGHT AHEAD


18. INSTALL COWL TOP PANEL OUTER


A115392
  1. Install the cowl top panel with the 9 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 57 in.*lbf }



    A108438
  1. Connect the wire harness clamp.



19. INSTALL NO. 2 COWL TO REGISTER DUCT SUB-ASSEMBLY


A108437
  1. Engage the claw to install cowl to register duct No. 2.



20. INSTALL FRONT WIPER MOTOR AND LINK


E113861
  1. Connect the connector.

  1. Slide the wiper link as shown in the illustration and engage the rubber pin with the body.

  1. Install the front wiper motor and link with the 2 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



21. INSTALL COWL TOP VENTILATOR LOUVER LH (for LHD)


E113853
  1. Engage the 4 claws and install the cowl top ventilator louver LH.

  1. Install the 2 clips.



22. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for LHD)


E113854
  1. Connect the washer hose.



    E113852
  1. Engage the 11 claws and install the cowl top ventilator louver sub-assembly.

  1. Install the clip.

  1. Connect the washer hose.



    E117641
  1. Engage the 2 hooks and install cowl top ventilator louver center No. 1.



23. INSTALL COWL TOP VENTILATOR LOUVER LH (for RHD)


E113856
  1. Engage the 4 claws and install the cowl top ventilator louver LH.

  1. Install the clip.



24. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for RHD)


E113855
  1. Engage the 10 claws and install the cowl top ventilator louver sub-assembly.

  1. Install the clip.

  1. Connect the washer hose.



25. INSTALL HOOD TO COWL TOP SEAL


E113851
  1. Engage the 7 clips and install the hood to cowl top seal.



26. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH


E058837E10
  1. Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.



    E113862E01
  1. Align the blade tip with the mark on the windshield glass, as shown in the illustration.

  1. Tighten the nut of the front wiper arm.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }



27. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH


E058837E10
  1. Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.



    E113863E01
  1. Align the blade tip with the mark on the windshield glass, as shown in the illustration.

  1. Tighten the nut of the front wiper arm.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }



28. INSTALL FRONT WIPER ARM HEAD CAP


E113849
  1. Engage the claw and install the 2 front wiper arm head caps.



29. INSPECT HOOD SUB-ASSEMBLY


  1. Check that the clearance measurements are within the standard ranges.


    B118065E01


    Standard:

    Area
    Measurement
    Area
    Measurement
    A
    1.7 to 5.7 mm
    (0.067 to 0.224 in.)
    G
    -1.55 to 2.45 mm
    (-0.061 to 0.096 in.)
    B
    -2 to 2 mm
    (-0.079 to 0.079 in.)
    H
    1.75 to 5.75 mm
    (0.067 to 0.226 in.)
    C
    4.45 to 10.45 mm
    (0.175 to 0.411 in.)
    I
    -1.25 to 2.75 mm
    (-0.049 to 0.108 in.)
    D
    -0.95 to 5.05 mm
    (-0.037 to 0.199 in.)
    J
    -1.5 to 1.5 mm
    (-0.059 to 0.059 in.)
    E
    7.55 to 13.55 mm
    (0.297 to 0.533 in.)
    K
    2.0 to 5.0 mm
    (0.079 to 0.197 in.)
    F
    1.65 to 5.65 mm
    (0.065 to 0.222 in.)
    -
    -



30. ADJUST HOOD SUB-ASSEMBLY


    B106963
  1. Loosen the hood side hinge bolts.

  1. Move the hood to adjust the clearance to within the standard range.

  1. Tighten the hood side hinge bolts after the adjustment.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }



    B106965
  1. Adjust the height of the hood front end by turning the cushion rubber.

    HINT:
    The cushion rubber can be raised and lowered by turning it.



    B106964
  1. Adjust the hood lock.

    1. Loosen the 3 bolts.

    2. Adjust the hood lock position so that the striker can enter it smoothly.

    3. Tighten the 3 bolts after the adjustment.

      Torque:
      7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



31. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



32. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT
(Click here)