Home › SUSPENSION & AXLE › SUSPENSION › REAR AXLE BEAM (for Sedan)

REAR AXLE BEAM (for Sedan) > INSTALLATION

for Preparation Click here



1. TEMPORARILY TIGHTEN REAR AXLE BEAM


    C112605E05
  1. Support the rear axle beam with a jack.

  1. Install the axle beam onto the vehicle and provisionally tighten the 2 bolts.



2. INSTALL REAR COIL SPRING LH
  1. Install the coil spring insulator lower onto the axle beam.



    C110329E01
  1. Install the coil spring insulator upper so that its gap fits onto the end of coil spring.



    C112606E01
  1. Install the coil spring onto the axle beam.

    NOTICE:
    The paint mark of the coil spring should be towards the underside and rear side of the vehicle.



3. INSTALL REAR COIL SPRING RH

HINT:
The installation procedure for the RH side is the same as that for the LH side.



4. TEMPORARILY TIGHTEN REAR SHOCK ABSORBER LH
  1. Support the axle beam with a jack. Insert a wooden block between the jack and the rear axle spring seat to prevent damage.

  1. Jack up the axle beam slowly, and provisionally install the shock absorber (lower side) with the bolt and nut onto the axle beam.

  1. Install the suspension support and cushion retainer.



    C106033
  1. While holding the piston rod, install a new nut (lower nut) to the specified standard.

    Standard:
    15 to 18 mm (0.591 to 0.709 in.)

  1. Hold the lower nut and tighten the upper nut against it.

    Torque:
    25 N*m{ 250 kgf*cm , 18 ft.*lbf }



5. TEMPORARILY TIGHTEN REAR SHOCK ABSORBER RH

HINT:
The installation procedure for the RH side is the same as that for the LH side.



6. INSTALL REAR SHOCK ABSORBER CAP LH


7. INSTALL REAR SHOCK ABSORBER CAP RH


8. INSTALL REAR AXLE HUB AND BEARING ASSEMBLY LH


    C121821
  1. Install the axle hub and bearing onto the axle beam with the 4 bolts.

    Torque:
    90 N*m{ 918 kgf*cm , 67 ft.*lbf }



9. INSTALL REAR AXLE HUB AND BEARING ASSEMBLY RH

HINT:
The installation procedure for the RH side is the same as that for the LH side.



10. INSPECT REAR AXLE HUB BEARING
  1. Remove the rear wheel.

  1. Remove the rear brake drum .



    C121815
  1. Inspect the axle hub and bearing backlash.

    1. Using a dial indicator, check the backlash near the center of the axle hub.

      Maximum:
      0.05 mm (0.0020 in.)

      If the backlash exceeds the maximum, replace the axle hub and bearing.



    C121816
  1. Inspect the axle hub and bearing runout.

    1. Using a dial indicator, check the runout of the surface of the axle hub.

      Maximum:
      0.07 mm (0.0028 in.)

      If the runout exceeds the maximum, replace the axle hub and bearing.

  1. Install the rear brake drum.

  1. Adjust the rear drum brake shoe clearance .

  1. Install the rear wheel.

    Torque:
    103 N*m{ 1,050 kgf*cm , 76 ft.*lbf }



11. INSTALL REAR BRAKE DRUM SUB-ASSEMBLY


12. ADJUST REAR DRUM BRAKE SHOE CLEARANCE


F040023E03
  1. Provisionally install the 2 hub nuts.

  1. Remove the hole plug, and turn the adjuster to expand the shoe until the drum locks.

  1. Using a screwdriver, release the adjuster 12 notches.

  1. Install the hole plug.



13. INSTALL NO. 3 PARKING BRAKE CABLE ASSEMBLY


    C126197
  1. Install the parking brake cable with the bolt and a new clamp.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }



14. INSTALL NO. 2 PARKING BRAKE CABLE ASSEMBLY

HINT:
The installation procedure for the RH side is the same as that for the LH side.



15. INSTALL REAR NO. 4 BRAKE TUBE


    C107570E04
  1. Install the brake tube onto the axle beam with the nut.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Connect the flexible hose to the axle beam with a new clip.

  1. Using SST, install the brake tube onto the flexible hose.

    SST
    09023-00100  

    Torque:
    for use without SST:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }
    for use with SST:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }

    HINT:
    1. Use a torque wrench with a fulcrum length of 300 mm (11.81 in.).
    2. This torque value is effective when SST is parallel to a torque wrench.



16. INSTALL REAR NO. 3 BRAKE TUBE

HINT:
The installation procedure for the RH side is the same as that for the LH side.



17. INSTALL SKID CONTROL SENSOR WIRE (w/ ABS)


    C107566
  1. Install the skid control sensor wire onto the axle beam with the nut.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }



    C107565
  1. Connect the skid control sensor wire connector.



18. INSTALL REAR WHEEL

Torque:
103 N*m{ 1050 kgf*cm , 76 ft.*lbf }



19. STABILIZE SUSPENSION
  1. Lower the vehicle from the jack.

  1. Bounce the vehicle up and down several times to stabilize the suspension.



20. FULLY TIGHTEN REAR AXLE BEAM


    C107574E05
  1. Suspend the jack on the rear axle spring seat and adjust the length of the shock absorber to the reference value.

    Length of shock absorber:
    220 mm (8.7 in.)

  1. Fully tighten the 2 bolts.

    Torque:
    90 N*m{ 918 kgf*cm , 67 ft.*lbf }



21. FULLY TIGHTEN REAR SHOCK ABSORBER LH
  1. Fully tighten the shock absorber (lower side) with the bolt.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }



22. FULLY TIGHTEN REAR SHOCK ABSORBER RH

HINT:
The installation procedure for the RH side is the same as that for the LH side.



23. INSTALL REAR SEATBACK ASSEMBLY (for Fixed Seat Type)


    B134981
  1. Engage the 3 hooks and install the rear seatback.

  1. Tighten the 3 bolts.

    Torque:
    7.9 N*m{ 80 kgf*cm , 70 in.*lbf }



    B138450E02
  1. Install the rear seat outer belt into the rear seat shoulder belt guide.

    HINT:
    Use the same procedure for both sides.

  1. for 3 Point Type Rear Center Seat belt:

    1. Install the rear center seat outer belt into the rear center seat shoulder belt guide.



24. INSTALL REAR SEAT CUSHION ASSEMBLY (for Fixed Seat Type)


    B138623
  1. Pass the rear seat inner belt through the rear seat cushion cover pad slit.

  1. Engage the 3 hooks and install the rear seat cushion cover pad.

    NOTICE:
    SE Make sure that the 2 rear seat cushion lock hooks and the rear seat cushion frame are securely engaged.



25. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



26. FILL RESERVOIR WITH BRAKE FLUID


C133125E02
  1. Remove the cowl top No. 2 ventilator louver center.



    C133126E01
  1. Set the brake fluid can upside down on the reservoir.

    Fluid:
    SAE J1703 or FMVSS No. 116 DOT3
    SAE J1704 or FMVSS No. 116 DOT4



27. BLEED MASTER CYLINDER

HINT:
If the master cylinder has been disassembled or if the reservoir becomes empty, bleed the air from the master cylinder.



    C116910E02
  1. Using a union nut wrench (10 mm), disconnect the brake tubes from the master cylinder.



    C116911E01
  1. Slowly depress the brake pedal and hold it there (Step A).



    C116912E01
  1. Block the outer holes with your fingers, and release the brake pedal (Step B).

  1. Repeat steps A and B 3 or 4 times.



    C116910E02
  1. Using a union nut wrench (10 mm), connect the brake tubes to the master cylinder.

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }

    NOTICE:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).



28. BLEED BRAKE LINE


C116913
  1. Connect the vinyl tube to the bleeder plug.

  1. Depress the brake pedal several times, then loosen the bleeder plug with the pedal depressed (Step C).

  1. At the point where the fluid stops coming out, tighten the bleeder plug, then release the brake pedal (Step D).

  1. Repeat steps C and D until all the air in the fluid is completely bled out.

  1. Tighten the bleeder plug.

    Torque:
    8.3 N*m{ 85 kgf*cm , 73 in.*lbf } for Front Brake
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf } for Rear Brake

  1. Repeat the above procedure to bleed the air out of the brake line for each wheel.



29. CHECK FLUID LEVEL IN RESERVOIR
  1. Check the fluid level and add fluid if necessary.

    Fluid:
    SAE J1703 or FMVSS No. 116 DOT3
    SAE J1704 or FMVSS No. 116 DOT4



30. INSPECT FOR BRAKE FLUID LEAK


31. INSPECT REAR WHEEL ALIGNMENT
  1. Inspect the rear wheel alignment (Click here).



32. CHECK ABS SENSOR SIGNAL (w/o VSC)
  1. Check the ABS sensor signal (Click here).



33. CHECK ABS SENSOR SIGNAL (w/ VSC)
  1. Check the ABS sensor signal (Click here).