Home › TRANSMISSION · CLUTCH › CLUTCH PEDAL (for Hatchback LHD)

CLUTCH PEDAL (for Hatchback LHD) > INSTALLATION

for Preparation Click here



1. INSTALL CLUTCH PEDAL NO.1 CUSHION


C115318
  1. Install the clutch pedal No. 1 cushion onto the clutch pedal.



2. INSTALL CLUTCH PEDAL BUSH


C115309
  1. Apply MP grease to the 2 bushes and collar.

  1. Install the 2 bushes and collar onto the clutch pedal.



3. INSTALL CLUTCH PEDAL PAD


4. INSTALL CLUTCH PEDAL SUB-ASSEMBLY


C115308
  1. Install the clutch pedal onto the clutch pedal support with the bolt and the nut.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }

    HINT:
    Install the bolt from the left side of the vehicle.



5. INSTALL CLUTCH PEDAL SPRING


6. INSTALL CLUTCH PEDAL STOPPER BOLT


C115317
  1. Install the clutch pedal stopper bolt so that its end touches the clutch pedal cushion.

    HINT:
    Tighten the lock nut to the specified torque when adjusting the clutch pedal.



7. INSTALL CLUTCH START SWITCH ASSEMBLY


C115315
  1. Install the clutch start switch with the nut.

    Torque:
    16 N*m{ 160 kgf*cm , 12 ft.*lbf }



8. INSTALL CLUTCH PEDAL SUPPORT SUB-ASSEMBLY


C115316
  1. Install the clutch pedal support onto the vehicle with the bolt.

    Torque:
    24 N*m{ 241 kgf*cm , 17 ft.*lbf }

  1. Connect the clutch start switch connector.

  1. Connect the wire harness clamp.



9. INSTALL CLUTCH MASTER CYLINDER ASSEMBLY


C115307
  1. Install the clutch master cylinder with the 2 nuts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }



10. CONNECT CLUTCH MASTER CYLINDER TO FLEXIBLE HOSE TUBE


C115313
  1. Using a union nut wrench 10 mm, connect the flexible hose tube.

    Torque:
    without union nut wrench:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }
    with union nut wrench:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }

    NOTICE:
    1. This torque value can be obtained by using a torque wrench with a fulcrum length of 300 mm (11.8 in.) and a union nut wrench with a fulcrum length of 22 mm (0.866 in.) (Click here).
    2. This torque value is effective when the union nut wrench is parallel to a torque wrench.



11. INSTALL CLUTCH RESERVOIR TUBE
  1. Connect the clutch reservoir tube with the clip to the clutch master cylinder assembly.



12. INSTALL INSTRUMENT PANEL SUB-ASSEMBLY UPPER
(Click here)


13. INSTALL BRAKE BOOSTER ASSEMBLY
(Click here)


14. INSPECT AND ADJUST CLUTCH PEDAL SUB-ASSEMBLY
  1. Pull back the floor carpet.



    C115306E01
  1. Check that the pedal height is correct.

    Pedal height from floor:
    for 1NZ-FE:
    133 to 143 mm (5.236 to 5.630 in.)
    for 2NZ-FE:
    118.1 to 128.1 mm (4.650 to 5.043 in.)

  1. If the pedal height is not as specified, adjust it as follows.

    1. Loosen the lock nut and turn the stopper bolt until the correct height is obtained.

    2. Tighten the lock nut.

      Torque:
      16 N*m{ 160 kgf*cm , 12 ft.*lbf }



15. INSPECT CLUTCH START SWITCH ASSEMBLY


D011485E10
  1. Check the resistance between the terminals when the switch is ON and OFF.

    Standard resistance:
    Switch position
    Specified Condition
    ON (pushed in)
    Below 1Ω
    OFF (released)
    10 kΩ or higher



16. INSTALL INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY LH (w/ Instrument Panel Under Cover)


    B114572
  1. Engage the 3 claws and install the instrument panel under cover.

  1. Tighten the 2 screws.