Home › TRANSMISSION ยท C54 MANUAL TRANSAXLE › MANUAL TRANSAXLE ASSEMBLY (for Sedan)

MANUAL TRANSAXLE ASSEMBLY (for Sedan) > INSTALLATION

for Preparation Click here



1. INSTALL MANUAL TRANSAXLE ASSEMBLY


C063143
  1. Align the input shaft with the clutch disc and install the manual transaxle onto the engine.

  1. Install the 7 bolts.

    Torque:
    33 N*m{ 336 kgf*cm , 24 ft.*lbf }



2. INSTALL TRANSVERSE ENGINE ENGINE MOUNTING BRACKET


C121108
  1. Install the engine mounting bracket LH with the 4 bolts.

    Torque:
    64 N*m{ 653 kgf*cm , 47 ft.*lbf }



3. INSTALL TRANSVERSE ENGINE ENGINE MOUNTING INSULATOR


C106372
  1. Install the engine mounting insulator LH with the 5 bolts.

    Torque:
    52 N*m{ 530 kgf*cm , 38 ft.*lbf }

  1. Install the engine mounting bracket LH and engine insulator LH with the bolt and nut.

    Torque:
    52 N*m{ 530 kgf*cm , 38 ft.*lbf }



4. INSTALL TRANSVERSE ENGINE ENGINE MOUNTING CONTROL BRACKET


C116856
  1. Install the engine mounting control bracket with the 4 bolts.

    Torque:
    64 N*m{ 653 kgf*cm , 47 ft.*lbf }



5. INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY
  1. Support the front suspension crossmember with a transmission jack.



    A108973E07
  1. Provisionally install the front suspension crossmember onto the body with the 6 bolts.
    Text in Illustration 
    *1
    Bolt A
    *2
    Bolt B
    *3
    Bolt C
    *a
    Front Side
    Bolt
    Underhead Length (mm)
    A
    38
    B
    99
    C
    45



  1. By inserting SST into the datum holes in the front suspension crossmembers RH and LH alternately, tighten bolts A, B and C on both sides to the specified torque, in several steps.


    C230201E01


    Text in Illustration 
    *1
    Bolt A
    *2
    Bolt B
    *3
    Bolt C
    *4
    for Bolt B with Bolt Strength Class 11T
    *5
    for Bolt B with Bolt Strength Class 10T
    -
    -
    *a
    Front Side
    *b
    Datum Hole
    *c
    OK
    *d
    NG
    SST
    09670-00011  

    Torque:
    Bolt A:
    87 N*m{ 887 kgf*cm , 64 ft.*lbf }
    Bolt B with Bolt Strength Class 11T:
    160 N*m{ 1631 kgf*cm , 118 ft.*lbf }
    Bolt B with Bolt Strength Class 10T:
    151 N*m{ 1540 kgf*cm , 111 ft.*lbf }
    Bolt C:
    98 N*m{ 999 kgf*cm , 72 ft.*lbf }

    NOTICE:
    1. Insert SST into the datum hole in a vertical orientation.
    2. If SST cannot be inserted into the datum hole vertically, loosen all the bolts and then insert SST again.

  1. Install the engine moving control rod with the bolt.

    Torque:
    120 N*m{ 1224 kgf*cm , 89 ft.*lbf }



6. INSTALL FRONT DRIVE SHAFT ASSEMBLY LH
  1. for Automatic Transaxle:

    1. Coat the spline of the inboard joint with ATF.

  1. for Manual Transaxle:

    1. Coat the spline of the inboard joint with gear oil.



    C116899
  1. Align the inboard joint splines and install the drive shaft with a screwdriver and hammer.

    NOTICE:
    1. Face the cut area of the front drive inboard joint hole snap ring downward.
    2. Do not damage the oil seal.
    3. Do not damage the inboard joint boot.

    HINT:
    Confirm whether the drive shaft is securely driven in by checking the reaction force and sound.



7. INSTALL FRONT DRIVE SHAFT ASSEMBLY RH

HINT:
The installation procedure for the RH side is the same as that for the LH side.



8. INSTALL FRONT AXLE ASSEMBLY LH
  1. Push the front axle out of the vehicle to align the spline of the drive shaft with the front axle and insert the front axle.

    NOTICE:
    1. Do not push the front axle further out of the vehicle than is necessary.
    2. Do not damage the outboard joint boot.
    3. Check for any foreign matter on the speed sensor rotor and insertion part.
    4. Do not damage the speed sensor rotor.



9. INSTALL FRONT AXLE ASSEMBLY RH

HINT:
The installation procedure for the RH side is the same as that for the LH side.



10. INSTALL FRONT STABILIZER LINK ASSEMBLY LH


    C106044
  1. Install the stabilizer link with the nut.

    Torque:
    74 N*m{ 755 kgf*cm , 55 ft.*lbf }

    HINT:
    If the ball joint turns together with the nut, use a socket hexagon wrench 6 to hold the stud.



11. INSTALL FRONT STABILIZER LINK ASSEMBLY RH

HINT:
The installation procedure for the RH side is the same as that for the LH side.



12. INSTALL TIE ROD END SUB-ASSEMBLY LH


    C107961
  1. Install the tie rod end onto the steering knuckle with a new castle nut.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }

    NOTICE:
    If the holes for the clip are not aligned, tighten the nut by a further turn of up to 60°.

  1. Install a new cotter pin.



13. INSTALL TIE ROD END SUB-ASSEMBLY RH

HINT:
The installation procedure for the RH side is the same as that for the LH side.



14. INSTALL FRONT SUSPENSION ARM SUB-ASSEMBLY LOWER NO.1 LH


    C107513
  1. Install the lower arm onto the steering knuckle with a new castle nut.

    Torque:
    98 N*m{ 1000 kgf*cm , 72 ft.*lbf }

    NOTICE:
    If the holes for the clip are not aligned, tighten the nut by a further turn of up to 60°.

  1. Install a new clip.



15. INSTALL FRONT SUSPENSION ARM SUB-ASSEMBLY LOWER NO.1 RH

HINT:
The installation procedure for the RH side is the same as that for the LH side.



16. INSTALL SPEED SENSOR FRONT LH (w/ ABS)


    C112274
  1. Install the speed sensor onto the steering knuckle with the bolt.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

    NOTICE:
    1. Check that the speed sensor tip and installation portion are free of foreign matter.
    2. Install the speed sensor without turning it from its original installation angle.



    C125274
  1. Install the flexible hose and speed sensor with the bolt.

    Torque:
    29 N*m{ 300 kgf*cm , 22 ft.*lbf }

    NOTICE:
    Install the flexible hose and speed sensor without twisting them.



17. INSTALL SPEED SENSOR FRONT RH (w/ ABS)

HINT:
The installation procedure for the RH side is the same as that for the LH side.



18. INSTALL FRONT AXLE SHAFT LH NUT


    C057566
  1. Using a 30 mm socket wrench, install a new axle hub nut.

    Torque:
    216 N*m{ 2203 kgf*cm , 160 ft.*lbf }

  1. Using a chisel and hammer, stake the axle hub nut.



19. INSTALL FRONT AXLE SHAFT RH NUT

HINT:
The installation procedure for the RH side is the same as that for the LH side.



20. INSTALL STARTER ASSEMBLY


A104498
  1. Install the starter assembly with the 2 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

  1. Connect the connector.

  1. Connect terminal 30 with the nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 7.2 ft.*lbf }

  1. Close the terminal cap.



21. CONNECT CONNECTOR
  1. Connect the back-up light switch connector.



22. CONNECT WIRE HARNESS


C108079
  1. Connect the wire harness with the bolt.

    Torque:
    26 N*m{ 260 kgf*cm , 19 ft.*lbf }



23. INSTALL CONTROL CABLE BRACKET


C106374
  1. Install the control cable bracket with the 2 bolts.

    Torque:
    25 N*m{ 250 kgf*cm , 18 ft.*lbf }



24. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY


C115305
  1. Connect the 2 cable ends and install the 2 washers and the 2 clips.

  1. Install 2 new clips onto the control cable bracket.



25. INSTALL CLUTCH RELEASE CYLINDER ASSEMBLY


C106371E01
  1. Install the clutch release cylinder and clutch pipe with the 4 bolts.

    Torque:
    12 N*m{ 120 kgf*cm , 8.7 ft.*lbf } for bolt A
    12 N*m{ 122 kgf*cm , 8.9 ft.*lbf } for bolt B



26. INSTALL BATTERY CARRIER


C106370
  1. Install the battery carrier with the 5 bolts.

    Torque:
    17 N*m{ 175 kgf*cm , 13 ft.*lbf }



27. INSTALL BATTERY TRAY


28. INSTALL BATTERY


29. INSTALL BATTERY CLAMP SUB-ASSEMBLY


30. INSTALL AIR CLEANER BRACKET


C106369
  1. Install the air cleaner bracket with the 2 bolts.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }



31. INSTALL AIR CLEANER ASSEMBLY


A104895
  1. Install the air cleaner case with air cleaner inlet No. 1 with the 2 bolts.

    Torque:
    7.8 N*m{ 80 kgf*cm , 69 in.*lbf }

  1. Connect the wire harness to the air cleaner case.

  1. Install the air cleaner element.



    A117355
  1. Install and lock the air cleaner cap and air cleaner hose and then tighten the air cleaner hose clamp.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }

  1. Connect the ventilation hose to the air cleaner hose.

  1. Connect the vacuum switching valve connector and wire harness clamp.

  1. Connect the fuel vapor feed hose and fuel vapor feed hose No. 1 to the vacuum switching valve assembly.

  1. Connect the intake air flow meter connector and wire harness clamp.



32. INSTALL CYLINDER HEAD COVER NO.2


A116235E01
  1. Tighten 2 A nuts, then 2 B nuts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }



33. INSTALL COWL TOP PANEL OUTER


A128448
  1. Install the cowl top panel outer with the 8 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 57 in.*lbf }



    A128447
  1. Install the cowl top to cowl inner brace with the 2 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 57 in.*lbf }



    A128446
  1. Connect the wire harness clamp.



34. INSTALL FRONT AIR SHUTTER SEAL


A133324
  1. Engage the 3 claws to install the front air shutter seal.



35. INSTALL WINDSHIELD WIPER MOTOR AND LINK


    E127840
  1. Connect the connector.

  1. Slide the wiper link as shown in the illustration and engage the rubber pin with the body.

  1. Install the front wiper motor and link with the 2 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



36. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for LHD)


    E127839
  1. Connect the washer hoses.

  1. Engage the 5 hooks.



    E127838
  1. Engage the 8 hooks and the 4 claws.

  1. Install the cowl top ventilator louver sub-assembly with the 3 clips.



37. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for RHD)


    E127836
  1. Connect the washer hoses.

  1. Engage the 5 hooks.



    E127835
  1. Engage the 10 hooks and the 6 claws.

  1. Install the cowl top ventilator louver sub-assembly with the 2 clips.



38. INSTALL COWL SIDE VENTILATOR SUB-ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



39. INSTALL COWL SIDE VENTILATOR SUB-ASSEMBLY LH


    E129651
  1. Engage the 3 claws and install the cowl side ventilator sub-assembly LH.



40. INSTALL HOOD TO COWL TOP SEAL


41. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH


    E058837E10
  1. Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.



    E113862E01
  1. Align the blade tip with the mark on the windshield glass, as shown in the illustration.

  1. Tighten the nut of the front wiper arm.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }



42. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH


    E058837E10
  1. Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.



    E129694E01
  1. Align the blade tip with the mark on the windshield glass, as shown in the illustration.

  1. Tighten the nut of the front wiper arm.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }



43. INSTALL HOOD SUB-ASSEMBLY


44. INSPECT HOOD SUB-ASSEMBLY


  1. Check that the clearance measurements are within the standard ranges.


    B140679E01


    Standard:

    Area
    Measurement
    Area
    Measurement
    A
    2.35 to 6.35 mm
    (0.092 to 0.250 in.)
    C
    2.0 to 5.0 mm
    (0.079 to 0.197 in.)
    B
    -2 to 2 mm
    (-0.079 to 0.079 in.)
    -
    -



45. ADJUST HOOD SUB-ASSEMBLY


    B136202
  1. Loosen the hood side hinge bolts.

  1. Move the hood to adjust the clearance to within the standard range.

  1. Tighten the hood side hinge bolts after the adjustment.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }



    B136203
  1. Adjust the height of the hood front end by turning the cushion rubber.

    HINT:
    The cushion rubber can be raised and lowered by turning it.



    B136204
  1. Adjust the hood lock.

    1. Loosen the 3 bolts.

    2. Adjust the hood lock position so that the striker can enter it smoothly.

    3. Tighten the 3 bolts after the adjustment.

      Torque:
      7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



46. ADD TRANSAXLE OIL


47. INSPECT AND ADJUST TRANSAXLE OIL


D025304E01
  1. Stop the vehicle in a level place.

  1. Remove the transmission filler plug and the gasket.

  1. Check that the oil surface is within 5 mm (0.20 in.) of the bottom of the transmission filler plug opening.

    NOTICE:
    1. Excessively large or small amounts of oil may cause problems.
    2. After replacing the oil, drive the vehicle and check the oil level again.

  1. Check for oil leakage when the oil level is low.

  1. Install the transmission filler plug and a new gasket.

    Torque:
    39 N*m{ 400 kgf*cm , 29 ft.*lbf }



48. INSTALL ENGINE UNDER COVER RH


49. INSTALL ENGINE UNDER COVER LH


50. INSTALL FRONT WHEELS


51. INSTALL STEERING SLIDE YOKE SUB-ASSEMBLY


C118005E08
  1. Align the matchmarks and install the sliding yoke onto the intermediate shaft with bolt B.
    Text in Illustration 
    *1
    Bolt A
    *2
    Bolt B
    *a
    Matchmark

    Torque:
    35 N*m{ 360 kgf*cm , 26 ft.*lbf }

  1. Tighten bolt A.

    Torque:
    35 N*m{ 360 kgf*cm , 26 ft.*lbf }



52. INSTALL COLUMN HOLE COVER SILENCER SHEET
  1. Install the column hole cover silencer sheet with the 2 clips.

  1. Install the floor carpet.



53. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



54. INSPECT ABS SPEED SENSOR SIGNAL
(Click here)


55. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT
(Click here)


56. CHECK FOR EXHAUST GAS LEAKAGE


57. CHECK FOR TRANSAXLE OIL LEAKAGE