Home › BRAKE › BRAKE › BRAKE PEDAL SUPPORT (for Sedan)

BRAKE PEDAL SUPPORT (for Sedan) > INSTALLATION

for Preparation Click here



1. INSTALL BRAKE PEDAL PAD
  1. Install the brake pedal pad onto the brake pedal.



2. INSTALL BRAKE PEDAL BUSH
  1. Apply lithium soap base glycol grease to the 2 bushes.

  1. Install the 2 bushes onto the brake pedal.



3. INSTALL BRAKE PEDAL
  1. Install the brake pedal onto the pedal support with the brake pedal shaft and nut.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }



4. INSTALL BRAKE PEDAL SUPPORT


C116881
  1. Install the pedal support with the bolt and 4 nuts.

    Torque:
    Bolt:
    24 N*m{ 241 kgf*cm , 17 ft.*lbf }
    Nut:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }



5. INSTALL BRAKE MASTER CYLINDER PUSH ROD CLEVIS
  1. Apply lithium soap base glycol grease to the push rod pin.



    C116880
  1. Install the push rod clevis with the push rod pin and clip.

  1. Install the brake pedal return spring.



6. INSTALL STOP LIGHT SWITCH MOUNTING ADJUSTER


C116879
  1. Install a new stop light switch mounting adjuster onto the pedal support.



7. INSTALL STOP LIGHT SWITCH


F049043E01
  1. Insert the stop light switch into the adjuster until it just touches the brake pedal.

    NOTICE:
    Do not depress the brake pedal.



    F049044E08
  1. Make a quarter turn clockwise to install the stop light switch.

    NOTICE:
    Do not depress the brake pedal.

    HINT:
    The turning torque for installing the stop light switch:

    Torque:
    1.5 N*m{ 15 kgf*cm , 13 in.*lbf } or less

  1. Check the stop light switch clearance.

    Stop light switch clearance:
    0.5 to 2.6 mm (0.020 to 0.102 in.)

  1. Connect the wire harness clamp onto the pedal support.

  1. Connect the connector to the stop light switch.



8. INSPECT AND ADJUST BRAKE PEDAL
  1. Remove the instrument panel under tray .



    C116874E01
  1. Inspect the brake pedal height.

    Pedal height from floor:
    w/ABS
    w/o ABS
    107.3 to 117.3 mm
    (4.224 to 4.618 in.)
    107.8 to 117.8 mm
    (4.244 to 4.638 in.)

    If the pedal height is incorrect, adjust it.



  1. Adjust the brake pedal height.

    1. Disconnect the connector from the stop light switch.

    2. Turn the stop light switch counterclockwise, and remove the stop light switch.

    3. Loosen the push rod lock nut.

    4. Adjust the pedal height by turning the pedal push rod.

      Pedal height from floor:
      w/ABS
      w/o ABS
      107.3 to 117.3 mm
      (4.224 to 4.618 in.)
      107.8 to 117.8 mm
      (4.244 to 4.638 in.)

    5. Tighten the push rod lock nut.

      Torque:
      26 N*m{ 265 kgf*cm , 19 ft.*lbf }



    6. F049043E01
    7. Insert the stop light switch into the adjuster until it just touches the brake pedal.

      NOTICE:
      Do not depress the brake pedal.



    8. F049044E08
    9. Make a quarter turn clockwise to install the stop light switch.

      NOTICE:
      Do not depress the brake pedal.

      HINT:
      The turning torque for installing the stop light switch:

      Torque:
      1.5 N*m{ 15 kgf*cm , 13 in.*lbf } or less

    10. Check the stop light switch clearance.

      Stop light switch clearance:
      0.5 to 2.6 mm (0.020 to 0.102 in.)

    11. Connect the connector to the stop light switch.



    F048932E01
  1. Inspect the brake pedal free play.

    1. Stop the engine and depress the brake pedal several times until there is no vacuum left in the booster.

    2. Push in the pedal until the beginning of the resistance is felt. Measure the distance as shown.

      Pedal free play:
      1.0 to 6.0 mm (0.039 to 0.236 in.)

      If incorrect, troubleshoot the brake system.



    R000934E02
  1. Inspect the brake pedal reserve distance.

    1. Release the parking brake lever. With the engine running, depress the pedal and measure the pedal reserve distance as shown.

      Pedal reserve distance from floor at 300 N (31 kgf, 67.4 lbf):

      LHD
      RHD
      w/ ABS
      More than 73 mm (2.87 in.)
      More than 74 mm (2.91 in.)
      w/o ABS
      More than 70 mm (2.75 in.)
      -

      HINT:
      Sound and resistance from the brake booster when the brake pedal is depressed without a vacuum does not indicate a problem.

      If incorrect, troubleshoot the brake system.

  1. Install the instrument panel under tray .



9. INSTALL NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY


    G028410E01
  1. Connect all the connectors and clamp the wire harnesses onto the steering post assembly bracket.

  1. Align the matchmarks on No. 2 steering intermediate shaft assembly and the steering sliding yoke and provisionally install them with bolt C.

    Torque:
    35 N*m{ 360 kgf*cm , 26 ft.*lbf }

  1. Align the matchmarks on the steering sliding yoke and steering gear assembly and install them with bolt B.

    Torque:
    35 N*m{ 360 kgf*cm , 26 ft.*lbf }

  1. Tighten bolt A.

    Torque:
    35 N*m{ 360 kgf*cm , 26 ft.*lbf }



10. INSTALL COLUMN HOLE COVER SILENCER SHEET
  1. Install the column hole cover silencer sheet with the 2 clips.

  1. Install the floor carpet.



11. INSTALL INSTRUMENT PANEL UNDER TRAY


B132333
  1. Engage the 6 claws and install the instrument panel under tray.

  1. Install the 2 <A> screws.



    B132390
  1. Engage the 4 claws and install the instrument panel under tray.



12. INSTALL UPPER INSTRUMENT PANEL SUB-ASSEMBLY


B130309E01
  1. Using a nipper, cut off both ends of the runner portion shown in the illustration (When installing a new one).

  1. Engage the 5 claws at the front side of the instrument panel.



  1. Engage the 7 clips at the rear side of the instrument panel.


    B132324



  1. Install the upper instrument panel with the 2 <C> bolts and the 2 <B> screws.


    B132323E01

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf } for bolt <C>



    B132386
  1. Connect the passenger airbag connector and clamp.



13. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY


B132321E01
  1. Engage the claws of the hinge portions by pushing the glove compartment door in the horizontal direction to install the glove compartment door assembly.

    NOTICE:
    Engage the claw by pushing it in the horizontal direction, otherwise, installation failure caused by excessive play around the hinge portion will result.



    B132319E01
  1. Slightly flex the upper portion of the glove compartment door assembly to engage the stopper.

  1. Install the glove compartment door stopper onto the glove compartment door.



14. INSTALL FRONT PILLAR GARNISH RH


    B138439E01
  1. w/ Curtain Shield Airbag:

    1. Remove the piece of cloth or nylon.



    B134787
  1. Install the 3 clamps.

  1. Connect the antenna connector.



    B134781E01
  1. w/ Curtain Shield Airbag:

    1. Install a new special clip and the clip onto the front pillar garnish.

    2. Engage the 2 clips and the 2 claws and install the front pillar garnish.



    B134779
  1. w/o Curtain Shield Airbag:

    1. Engage the 2 clips and the 2 claws and install the front pillar garnish.



15. INSTALL FRONT PILLAR GARNISH LH


    B138440
  1. w/ Curtain Shield Airbag:

    1. Remove the piece of cloth or nylon.



    B134789
  1. Install the 4 clamps.



    B134782E01
  1. w/ Curtain Shield Airbag:

    1. Install a new special clip and the clip onto the front pillar garnish.

    2. Engage the 2 clips and the 2 claws and install the front pillar garnish.



    B134780
  1. w/o Curtain Shield Airbag:

    1. Engage the 2 clips and the 2 claws and install the front pillar garnish.



16. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH
  1. Install the front door opening trim weatherstrip.



17. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH
  1. Install the front door opening trim weatherstrip.



18. INSTALL COMBINATION METER ASSEMBLY


E116835E01
  1. Install the combination meter assembly with the 2 screws.

    NOTICE:
    Install the combination meter so that the rib of the combination meter is held between the instrument panel and the instrument cluster finish panel.

  1. Connect the 2 connectors.



19. INSTALL INSTRUMENT CLUSTER FINISH PANEL NO.1


E116833
  1. Fit the 2 claws of the instrument cluster finish panel into the upper instrument cluster finish panel center.



    E116834
  1. Engage the 5 claws and 5 clips and install the instrument cluster finish panel.



20. INSTALL INSTRUMENT PANEL FINISH PANEL END RH


B132318
  1. Engage the 6 claws and 3 clips and install the instrument panel finish panel end RH.



21. INSTALL INSTRUMENT PANEL FINISH PANEL END LH


B132317
  1. Engage the 6 claws and 3 clips and install the instrument panel finish panel end LH.



22. INSTALL INSTRUMENT PANEL FINISH PANEL LOWER CENTER


B132316
  1. Engage the 2 claws and 2 clips and install the instrument panel finish panel lower center.



23. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



24. INSPECT SRS WARNING LIGHT
(Click here)