ENGINE > ON-VEHICLE INSPECTION |
| 1. INSPECT ENGINE COOLANT |
The engine coolant should be between the LOW and FULL lines when the engine is cold.
| 2. INSPECT ENGINE OIL |
Warm up the engine, then stop the engine and wait for 5 minutes. Check that the engine oil level is between the low and full marks on the oil level gauge.
If the engine oil level is low, check for oil leakage and add engine oil up to the full level mark.
| 3. INSPECT BATTERY |
Check the battery for damage and deformation. If severe damage, deformation or leakage is found, replace the battery.
Check the volume of electrolyte in each cell.
For batteries that are maintenance-free:
For batteries that are not maintenance-free:
| 4. INSPECT AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY |
Remove the air cleaner filter element sub-assembly.
Visually check that there is no dirt, blockage, or damage to the air cleaner filter element.
| 5. INSPECT SPARK PLUG |
![]() |
Check the electrode.
Using a megaohmmeter, measure the insulation resistance.
Alternative inspection method.
Quickly accelerate the engine to 4,000 rpm 5 times.
Remove the spark plug.
![]() |
Visually check the spark plug.
If the electrode is dry, the spark plug is functioning properly. If the electrode is damp, proceed to the next step.
Check the spark plug for any damage on its thread and insulator.
If there is damage, replace the spark plug.
| Manufacturer | Product |
| DENSO | K16R-U |
| NGK | BKR5EYA |
![]() |
Check the spark plug electrode gap.
![]() |
Clean the spark plugs.
If the electrode has traces of wet carbon, clean the electrode with a spark plug cleaner and then dry it.
| 6. INSPECT IGNITION TIMING |
When using an intelligent tester:
Warm up and stop the engine.
![]() |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Select the following menu items:
Powertrain / Engine and ECT / Active Test / TC (TE1) / ON.
Inspect the ignition timing during idling.
Select the following menu items: TC (TE1) / OFF
Turn the ignition switch off.
Disconnect the intelligent tester from the DLC3.
When not using an intelligent tester:
Remove cylinder head cover No. 2 .
![]() |
Pull out the wire harness (brown) shown in the illustration.
Warm up and stop the engine.
Connect the clip of the timing light to the wire harness.
Turn the ignition switch on (IG).
![]() |
Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.
Inspect the ignition timing during idling.
Disconnect terminals 13 (TC) and 4 (CG) of the DLC3.
Turn the ignition switch off.
Remove the timing light.
Install cylinder head cover No. 2 .
| 7. INSPECT ENGINE IDLING SPEED |
When using an intelligent tester:
Warm up and stop the engine.
![]() |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Select the following menu items: Powertrain / Engine and ECT /Data List / Engine Speed.
Inspect the engine idling speed.
Turn the ignition switch off.
Disconnect the intelligent tester from the DLC3.
When not using an intelligent tester.
Warm up and stop the engine.
![]() |
Install SST to terminal 9 (TAC) of the DLC3, then connect a tachometer.
Turn the ignition switch on (IG).
Inspect the engine idling speed.
Turn the ignition switch off.
Disconnect the tachometer.
Remove SST from terminal 9 (TAC).
| 8. INSPECT COMPRESSION |
Warm up and stop the engine.
Remove cylinder head cover No. 2 .
Remove the 4 ignition coils .
Remove the 4 spark plugs.
Disconnect the 4 fuel injector connectors.
![]() |
Inspect the cylinder compression pressure.
Insert a compression gauge into the spark plug hole.
Fully open the throttle.
While cranking the engine, measure the compression pressure.
If the cylinder compression is low, pour a light coat of engine oil into the cylinder through the spark plug hole, then inspect it again.
Connect the 4 fuel injector connectors.
Install the 4 spark plugs.
Install the 4 ignition coils .
Install cylinder head cover No. 2 .
| 9. INSPECT CO/HC |
Start the engine.
Run the engine at 2,500 rpm for approximately 180 seconds.
Insert the CO/HC meter testing probe at least 40 cm (1.3 ft) into the tailpipe while idling.
Check the CO/HC concentration during idling and when running at 2,500 rpm.
Check the heated oxygen sensor operation (Click here).
See the table below for possible causes, then inspect the applicable parts and repair them if necessary.
| CO | HC | Problems | Possible Causes |
| Normal | High | Rough idling |
|
| Low | High | Rough idling (Fluctuating HC reading) |
|
| High | High | Rough idling (Black smoke from exhaust) |
|