Home › BODY › INSTRUMENT PANEL › LOWER INSTRUMENT PANEL (for Sedan)

LOWER INSTRUMENT PANEL (for Sedan) > INSTALLATION

for Preparation Click here



1. INSTALL INSTRUMENT PANEL NO. 1 SAFETY PAD


B132362
  1. Apply butyl tape to install the instrument panel safety pad No. 1 onto the instrument panel lower (When installing a new one).



2. INSTALL INSTRUMENT PANEL NO. 2 SAFETY PAD


B132361
  1. Apply butyl tape to install the instrument panel safety pad No. 2 onto the instrument panel lower (When installing a new one).



3. INSTALL INSTRUMENT CLUSTER FINISH PANEL SEAL


B132393
  1. Engage the 5 claws and install the panel seal.



4. INSTALL INSTRUMENT PANEL HOLE COVER


B130144
  1. Install the instrument panel hole cover with the 2 <H> screws.



5. INSTALL STEREO JACK ADAPTER ASSEMBLY


B132360
  1. Engage the 2 claws and install the stereo jack adapter.



6. INSTALL HEADLIGHT LEVELING SWITCH


B132359
  1. Engage the 2 claws and install the headlight leveling switch.



7. INSTALL OUTER MIRROR SWITCH ASSEMBLY


B132357
  1. Engage the 2 claws and install the outer mirror switch.



8. INSTALL GLOVE COMPARTMENT DOOR STOPPER SUB-ASSEMBLY


B132392
  1. Engage the claw and install the glove compartment door stopper.



9. INSTALL INSTRUMENT PANEL CUP HOLDER SUB-ASSEMBLY LH


B132343
  1. Install the instrument panel cup holder with the 3 <A> screws.



10. INSTALL INSTRUMENT PANEL CUP HOLDER SUB-ASSEMBLY RH


B132344
  1. Install the instrument panel cup holder with the 3 <A> screws.



11. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY


    B132391E01
  1. Using a nipper, cut off both ends of the runner portion shown in the illustration (When installing a new one).

  1. Install the lower instrument panel with the 6 <D> bolts, 2 <E> bolts, screw <G> and screw <H>.

    NOTICE:
    Do not excessively tighten the <D> bolts, as this, may damage the area not being tightened.



  1. Connect the clamps and connectors.


    B132342E01



    B108192
  1. Engage the 2 claws and connect the DLC3 connector.



12. CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY


B132338
  1. Engage the 3 claws to connect the control lever.



13. CONNECT ANTENNA CORD SUB-ASSEMBLY


    B132369
  1. for LHD:

    1. Connect the 5 antenna cord clamps.



    B132370
  1. for RHD:

    1. Connect the 4 antenna cord clamps.



14. INSTALL INSTRUMENT PANEL BOX


B132335E01
  1. Insert the stopper of the instrument panel box from the cutout of the instrument panel lower.



    B132337E01
  1. Engage the 2 hinges with the instrument panel open.

  1. Close the instrument panel box.



15. INSTALL INSTRUMENT PANEL UNDER TRAY


B132333
  1. Engage the 6 claws and install the instrument panel under tray.

  1. Install the 2 <A> screws.



    B132390
  1. Engage the 4 claws and install the instrument panel under tray.



16. INSTALL INSTRUMENT PAD LOWER RH


    B132340
  1. Engage the claw and 3 clips and install the instrument pad lower.

  1. Install screw <I>.



17. INSTALL INSTRUMENT PAD LOWER LH


    B132339
  1. Engage the claw and 3 clips and install the instrument pad lower.

  1. Install screw <I>.



18. INSTALL REAR CONSOLE BOX ASSEMBLY


    B132349
  1. Engage the 4 claws and install the rear console box.

  1. Install the 2 bolts and 2 screws.

  1. Connect the clamp.



19. INSTALL CONSOLE BOX CARPET


    B132346
  1. Install the console box carpet.



20. INSTALL CONSOLE UPPER REAR PANEL SUB-ASSEMBLY


    B132348
  1. Connect the connector.

  1. Engage the 3 clips and 3 claws and install the console upper rear panel.



21. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY


    B132347
  1. Engage the 5 clips and the claw and install the upper console panel.



22. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transaxle)


    B132388
  1. Install the shift lever knob.



23. INSTALL COWL SIDE TRIM BOARD RH


    B114285
  1. Engage the stud bolt and the claw and install the cowl side trim board.



24. INSTALL COWL SIDE TRIM BOARD LH

HINT:
Use the same procedure as for the RH side.



25. INSTALL FRONT DOOR SCUFF PLATE RH


    B134764
  1. Engage the 11 claws and install the front door scuff plate.



26. INSTALL FRONT DOOR SCUFF PLATE LH

HINT:
Use the same procedure as for the RH side.



27. INSTALL UPPER INSTRUMENT PANEL SUB-ASSEMBLY


B130309E01
  1. Using a nipper, cut off both ends of the runner portion shown in the illustration (When installing a new one).

  1. Engage the 5 claws at the front side of the instrument panel.



  1. Engage the 7 clips at the rear side of the instrument panel.


    B132324



  1. Install the upper instrument panel with the 2 <C> bolts and the 2 <B> screws.


    B132323E01

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf } for bolt <C>



    B132386
  1. Connect the passenger airbag connector and clamp.



28. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY


B132321E01
  1. Engage the claws of the hinge portions by pushing the glove compartment door in the horizontal direction to install the glove compartment door assembly.

    NOTICE:
    Engage the claw by pushing it in the horizontal direction, otherwise, installation failure caused by excessive play around the hinge portion will result.



    B132319E01
  1. Slightly flex the upper portion of the glove compartment door assembly to engage the stopper.

  1. Install the glove compartment door stopper onto the glove compartment door.



29. INSTALL FRONT PILLAR GARNISH RH


    B138439E01
  1. w/ Curtain Shield Airbag:

    1. Remove the piece of cloth or nylon.



    B134787
  1. Install the 3 clamps.

  1. Connect the antenna connector.



    B134781E01
  1. w/ Curtain Shield Airbag:

    1. Install a new special clip and the clip onto the front pillar garnish.

    2. Engage the 2 clips and the 2 claws and install the front pillar garnish.



    B134779
  1. w/o Curtain Shield Airbag:

    1. Engage the 2 clips and the 2 claws and install the front pillar garnish.



30. INSTALL FRONT PILLAR GARNISH LH


    B138440
  1. w/ Curtain Shield Airbag:

    1. Remove the piece of cloth or nylon.



    B134789
  1. Install the 4 clamps.



    B134782E01
  1. w/ Curtain Shield Airbag:

    1. Install a new special clip and the clip onto the front pillar garnish.

    2. Engage the 2 clips and the 2 claws and install the front pillar garnish.



    B134780
  1. w/o Curtain Shield Airbag:

    1. Engage the 2 clips and the 2 claws and install the front pillar garnish.



31. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH
  1. Install the front door opening trim weatherstrip.



32. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH
  1. Install the front door opening trim weatherstrip.



33. CONNECT AIR INLET DAMPER CONTROL CABLE SUB-ASSEMBLY


I102570
  1. Engage the 2 claws and connect the air inlet damper control cable.



34. CONNECT DEFROSTER DAMPER CONTROL CABLE SUB-ASSEMBLY


I102569
  1. Engage the 2 claws and connect the defroster damper control cable.



35. CONNECT AIR MIX DAMPER CONTROL CABLE SUB-ASSEMBLY


I102568
  1. Engage the 2 claws and connect the air mix control cable clamp.

  1. Connect the air mix damper control cable to the clamp.



36. INSTALL AIR CONDITIONING PANEL ASSEMBLY


I102567
  1. Connect the 3 connectors and the 4 clamps.



    I102566
  1. Engage the 4 clips and 2 claws and install the air conditioning panel.



37. INSTALL STEREO OPENING COVER (w/o Radio Receiver)


B132396
  1. Install the stereo opening cover with the 4 screws.



38. INSTALL RADIO RECEIVER ASSEMBLY


    B138304
  1. Connect the plug.

  1. Connect the 2 radio connectors.



    B138303
  1. Align the 2 bosses of the instrument panel with the hole in the radio bracket.

  1. Install the radio receiver with the 4 bolts.



39. INSTALL INSTRUMENT CLUSTER FINISH PANEL CENTER SUB-ASSEMBLY


B132395
  1. Engage the 2 claws and 4 clips and install the instrument cluster finish panel center.



40. INSTALL COMBINATION METER ASSEMBLY


E116835E01
  1. Install the combination meter assembly with the 2 screws.

    NOTICE:
    Install the combination meter so that the rib of the combination meter is held between the instrument panel and the instrument cluster finish panel.

  1. Connect the 2 connectors.



41. INSTALL INSTRUMENT CLUSTER FINISH PANEL NO.1


E116833
  1. Fit the 2 claws of the instrument cluster finish panel into the upper instrument cluster finish panel center.



    E116834
  1. Engage the 5 claws and 5 clips and install the instrument cluster finish panel.



42. INSTALL INSTRUMENT PANEL FINISH PANEL END RH


B132318
  1. Engage the 6 claws and 3 clips and install the instrument panel finish panel end RH.



43. INSTALL INSTRUMENT PANEL FINISH PANEL END LH


B132317
  1. Engage the 6 claws and 3 clips and install the instrument panel finish panel end LH.



44. INSTALL INSTRUMENT PANEL FINISH PANEL LOWER CENTER


B132316
  1. Engage the 2 claws and 2 clips and install the instrument panel finish panel lower center.



45. INSTALL INSTRUMENT PANEL CUP HOLDER SPRING RH


B132402
  1. Install the spring.



46. INSTALL INSTRUMENT PANEL CUP HOLDER RH


B132401E01
  1. Install the 2 hinges of the cup holder one at a time.



    B132399
  1. Engage the spring with the instrument panel cup holder.



    B132398E01
  1. Flex both sides of the cup holder and engage the 2 stoppers.

  1. Close the instrument panel cup holder.



47. INSTALL INSTRUMENT PANEL CUP HOLDER SPRING LH


B132406
  1. Install the spring.



48. INSTALL INSTRUMENT PANEL CUP HOLDER LH


B132405E01
  1. Install the 2 hinges of the cup holder one at a time.

    HINT:
    Make sure that the spring is set in the position shown in the illustration.



    B132403E01
  1. Flex both sides of the cup holder and engage the 2 stoppers.

  1. Close the instrument panel cup holder.



49. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



50. CHECK SRS WARNING LIGHT
(Click here)


51. INSTALL STEREO OPENING COVER (w/o Radio Receiver)