Home › RESTRAINTS › SEAT BELT › FRONT SEAT OUTER BELT ASSEMBLY (for Hatchback 3 Door Rear Split Seat Type)

FRONT SEAT OUTER BELT ASSEMBLY (for Hatchback 3 Door Rear Split Seat Type) > INSTALLATION

for Preparation Click here


CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (Click here).

NOTICE:
Always use "TORX" socket wrench E10 when installing the rear seat.

HINT:
The procedure described below is for the RH side. Use the same procedure for both the RH and LH sides, unless otherwise specified.



1. INSTALL FRONT SEAT OUTER BELT ASSEMBLY


    B114426E01
  1. Check the angle of inclination required to lock the retractor.

    1. Gently incline the retractor from its initial position. Check that the belt does not lock when the retractor is inclined 15° or less in any direction. Also, check that the belt locks when the inclination of the retractor is 45° or more.

      NOTICE:
      Do not disassemble the retractor.

      If the operation is not as specified, replace the front seat outer belt.



    B114423E01
  1. Hook the lower stay of the retractor onto the 2 body hooks and provisionally install the retractor with the 2 bolts.

  1. Tighten bolt A and then bolt B.

    Torque:
    4.9 N*m{ 50 kgf*cm , 43 in.*lbf } for bolt A
    42 N*m{ 430 kgf*cm , 31 ft.*lbf } for bolt B



    B114479
  1. Install the through anchor with the bolt.

    Torque:
    42 N*m{ 430 kgf*cm , 31 ft.*lbf }

  1. Check that the ELR locks.

    NOTICE:
    Perform the check with the front seat outer belt installed.


    1. With the belt installed, check that the belt locks when it is pulled out quickly.
      If the operation is not as specified, replace the front seat outer belt.



    B114497
  1. w/o Seat Belt Bar:

    1. Install the anchor plate with the bolt.

      Torque:
      42 N*m{ 430 kgf*cm , 31 ft.*lbf }



    2. B114496
    3. Install the anchor plate cover.



    B114427E01
  1. Connect the pretensioner connector.

    1. Connect the pretensioner connector.

    2. Lock the locking button.

      NOTICE:
      Securely lock the locking button.



2. INSTALL SEAT BELT ANCHOR COVER CAP


    B114478
  1. Engage the 3 claws and install the seat belt anchor cover cap.



3. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY


    B114499
  1. Engage the 8 clips, the retainer and the 10 claws and install the front quarter trim panel.



4. INSTALL REAR SEAT OUTER BELT ASSEMBLY


    B114498
  1. Install the belt.



5. INSTALL FRONT SEAT OUTER BELT BAR SUB-ASSEMBLY (w/ Seat Belt Bar)


    B114759
  1. Install the front seat outer belt bar with the 2 bolts.

    Torque:
    42 N*m{ 430 kgf*cm , 31 ft.*lbf }



6. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP


    B114477
  1. Install the front door opening trim weatherstrip.



7. INSTALL FRONT DOOR SCUFF PLATE


    B114494
  1. Engage the 8 claws and install the front door scuff plate.



8. INSTALL REAR SEAT ASSEMBLY
  1. for RH Side:

    1. Install the rear seat assembly .

  1. for LH Side:

    1. Install the rear seat assembly .



9. INSTALL NO. 2 REAR SEAT LEG COVER (for LH Side)


    B114739
  1. Engage the 3 claws and install the No. 2 rear seat leg cover.



10. INSTALL NO. 1 REAR SEAT LEG COVER
  1. for RH Side:

    1. Install the No. 1 rear seat leg cover .

  1. for LH Side:

    1. Install the No. 1 rear seat leg cover .



11. INSTALL DECK FLOOR BOX (w/ Deck Board)
  1. for RH Side:

    1. Install the deck floor box .

  1. for LH Side:

    1. Install the deck floor box.

      HINT:
      Use the same procedure as for the RH side.



12. INSTALL SPARE WHEEL COVER ASSEMBLY (w/ Deck Board)


    B119913
  1. Install the spare wheel cover.



13. INSTALL DECK BOARD SUB-ASSEMBLY (w/ Deck Board)


    B106447
  1. Set the deck board and lock the 2 knobs.



14. INSTALL REAR FLOOR CARPET ASSEMBLY (w/o Deck Board)


    B119912
  1. Install the rear floor carpet.



15. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Package Tray Trim)


    B114569E01
  1. Engage the 2 claws and install the package tray trim panel.

  1. Install the 5 pieces of hook tape.

  1. Install the 2 package tray trim suspenders.



16. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



17. INSPECT SRS WARNING LIGHT
(Click here)