FRONT DRIVE SHAFT (for Sedan) > INSTALLATION |
| 1. INSTALL FRONT DRIVE SHAFT ASSEMBLY LH |
for Automatic Transaxle:
Coat the spline of the inboard joint with ATF.
for Manual Transaxle:
Coat the spline of the inboard joint with gear oil.
![]() |
Align the inboard joint splines and install the drive shaft with a screwdriver and hammer.
| 2. INSTALL FRONT DRIVE SHAFT ASSEMBLY RH |
| 3. INSTALL FRONT AXLE ASSEMBLY |
Push the front axle out of the vehicle to align the spline of the drive shaft with the front axle and insert the front axle.
| 4. INSTALL FRONT SUSPENSION LOWER ARM |
![]() |
Install the lower arm onto the steering knuckle with a new castle nut.
Install a new clip.
| 5. INSTALL FRONT STABILIZER LINK ASSEMBLY |
![]() |
Install the stabilizer link with the nut.
| 6. INSTALL TIE ROD END SUB-ASSEMBLY |
![]() |
Install the tie rod end onto the steering knuckle with a new castle nut.
Install a new cotter pin.
| 7. INSTALL FRONT FLEXIBLE HOSE (w/o ABS) |
![]() |
Install the flexible hose with the bolt.
| 8. INSTALL FRONT SPEED SENSOR (w/ ABS) |
![]() |
Install the speed sensor onto the steering knuckle with the bolt.
![]() |
Install the flexible hose and speed sensor with the bolt.
| 9. INSTALL FRONT AXLE HUB NUT |
![]() |
Using a 30 mm socket wrench, install a new axle hub nut.
Using a chisel and hammer, stake the axle hub nut.
| 10. INSTALL FRONT WHEEL |
| 11. ADD AUTOMATIC TRANSAXLE FLUID (for U441E Automatic Transaxle) |
| Drain and refill | 2.5 liters (2.6 US qts, 2.2 Imp. qts) |
| Dry fill | 5.6 liters (5.9 US qts, 4.9 Imp. qts) |
| 12. ADD AUTOMATIC TRANSAXLE FLUID (for U340E Automatic Transaxle) |
| Drain and refill | 2.5 liters (2.6 US qts, 2.2 Imp. qts) |
| Dry fill | 6.4 liters (6.8 US qts, 5.6 Imp. qts) |
| 13. ADD TRANSAXLE OIL (for C54 Manual Transaxle) |
| 14. INSPECT AUTOMATIC TRANSAXLE FLUID (for U441E Automatic Transaxle) |
![]() |
Park the vehicle on a level surface and engage the parking brake.
With the engine idling and the brake pedal depressed, shift the shift lever into all positions from P to L, and then return it to the P position.
Pull out the oil level gauge and wipe it clean.
Push it fully back into the pipe.
Pull it out and check that the fluid level is within the HOT range.
If there is any leakage, repair or replace O-rings, FIPGs, oil seals, plugs or other parts.
| 15. INSPECT AUTOMATIC TRANSAXLE FLUID (for U340E Automatic Transaxle) |
![]() |
Park the vehicle on a level surface and engage the parking brake.
With the engine idling and the brake pedal depressed, shift the shift lever into all positions from P to L, and then return it to the P position.
Pull out the oil level gauge and wipe it clean.
Push it fully back into the pipe.
Pull it out and check that the fluid level is within the HOT range.
If there is any leakage, repair or replace O-rings, FIPGs, oil seals, plugs or other parts.
| 16. INSPECT MANUAL TRANSAXLE OIL (for C54 Manual Transaxle) |
![]() |
Stop the vehicle in a level place.
Remove the transmission filler plug and the gasket.
Check that the oil surface is within 5 mm (0.20 in.) of the bottom of the transmission filler plug opening.
Check for oil leakage when the oil level is low.
Install the transmission filler plug and a new gasket.
| 17. INSPECT FOR AUTOMATIC TRANSAXLE FLUID LEAK (for Automatic Transaxle) |
| 18. INSPECT FOR TRANSAXLE OIL LEAK (for Manual Transaxle) |
| 19. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT |
Inspect and adjust the front wheel alignment (Click here).
| 20. CHECK ABS SENSOR SIGNAL (w/o VSC) |
Check the ABS sensor signal (Click here).
| 21. CHECK ABS SENSOR SIGNAL (w/ VSC) |
Check the ABS sensor signal (Click here).