Home › BRAKE › BRAKE CONTROL › ANTI-LOCK BRAKE SYSTEM (for Sedan)

DTC    C1249/49    Open in Stop Light Switch Circuit

for Preparation Click here


DESCRIPTION

The skid control ECU detects the brake operating conditions through a signal transmitted by the stop light switch. The skid control ECU incorporates an open circuit detection circuit. This DTC is set under either of the following conditions:
  1. An open is detected in the stop light signal input line when the stop light switch is off.
  2. An open is detected in the stop light circuit lead to the ground when the stop light switch is off.

DTC No.
DTC Detecting Conditions
Trouble Areas
C1249/49
When IG1 terminal voltage 9.5 to 17.2 V, open circuit of stop light switch continues for 0.3 seconds or more.
  1. Stop light switch
  2. Stop light switch circuit
  3. Brake actuator

WIRING DIAGRAM


C136888E02


INSPECTION PROCEDURE

1.CHECK STOP LIGHT SWITCH OPERATION


    A107926E08
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Select the DATA LIST mode on the intelligent tester.
    Select the following menu items: Chassis / ABS/VSC/TRC / Data List.

    DATA LIST: ABS 
    Item (Display)
    Measurement Item / Range (Display)
    Normal Conditions
    Stop Lamp SW
    Stop light switch / ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released

  1. Check that "Stop Lamp SW" is turned ON and OFF when the brake pedal is depressed and released.

    OK:
    "Stop Lamp SW" is turned ON and OFF in accordance with the operation of the brake pedal.



NG
Go to step 3
OK


2.CHECK SKID CONTROL ECU TERMINAL VOLTAGE (STP)
  1. Disconnect the skid control ECU connector.



    C117862E05
  1. Measure the voltage.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A15-10 (STP) - Body ground
    Brake pedal depressed
    8 to 14 V
    A15-10 (STP) - Body ground
    Brake pedal released
    Below 4.0 V



NG
Go to step 5
OK

REPLACE BRAKE ACTUATOR 

3.INSPECT FUSE (STOP)


    C118695E01
  1. Remove the STOP fuse from the main body ECU.

  1. Measure the resistance.

    Standard Resistance:
    Below 1 Ω



NG
CHECK FOR SHORTS IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSE
OK


4.INSPECT STOP LIGHT SWITCH ASSEMBLY
C118699E05
  1. Disconnect the stop light switch connector.

  1. Measure the resistance.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    Switch pin released
    Below 1 Ω
    3 - 4
    Switch pin released
    10 kΩ or higher
    1 - 2
    Switch pin pushed in
    10 kΩ or higher
    3 - 4
    Switch pin pushed in
    Below 1 Ω



NG
REPLACE STOP LIGHT SWITCH ASSEMBLY
OK


5.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - STOP LIGHT SWITCH)
  1. Disconnect the skid control ECU connector and stop light switch connector.



    C118696E01
  1. Measure the resistance.

    Standard Resistance:
    Tester Connection
    Specified Condition
    A15-10 (STP) - A13-1
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.RECONFIRM DTC
  1. Clear the DTC (Click here).

  1. Check if the same DTC is output (Click here).

    Result
    Proceed to
    DTC output
    A
    DTC not output
    B



B
END
A

REPLACE BRAKE ACTUATOR