REAR AIRBAG SENSOR (for Hatchback 3 Door) > INSTALLATION |
| 1. INSTALL REAR AIRBAG SENSOR |
Confirm that the ignition switch is turned to off.
Confirm that the negative battery terminal is detached.
![]() |
Insert the hook into the body hole and install the airbag sensor with the bolt.
Confirm that there is no looseness by shaking the rear airbag sensor.
![]() |
Connect the airbag connector.
| 2. INSTALL DECK SIDE TRIM PANEL ASSEMBLY RH |
![]() |
Engage the 3 clips and the 3 claws and install the deck side trim panel.
Tighten the 3 screws.
| 3. INSTALL REAR SEAT OUTER BELT ASSEMBLY RH |
![]() |
Engage the clip and install the anchor plate.
Tighten the bolt.
| 4. INSTALL REAR DECK TRIM COVER |
![]() |
for Grand Tire:
Engage the 8 claws and install the rear deck trim cover.
Install the 2 clips.
![]() |
for Temper Spare Tire:
Engage the 8 claws and install the rear deck trim cover.
Install the 2 clips.
| 5. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY RH |
![]() |
Engage the 8 clips, the retainer and the 10 claws and install the front quarter trim panel.
![]() |
Install the belt of the rear seat outer belt onto the rear seat shoulder belt hanger.
| 6. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH |
![]() |
Install the rear door opening trim weatherstrip.
| 7. INSTALL FRONT DOOR SCUFF PLATE RH |
![]() |
Engage the 8 claws and install the front door scuff plate.
| 8. INSTALL REAR SEAT ASSEMBLY LH |
![]() |
Insert the 2 location pins through the 2 body holes and install the rear seat.
Using "TORX" socket wrench E10, install the 4 bolts in the sequence shown in the illustration.
![]() |
Install the rear seat cushion.
Using "TORX" socket wrench E10, install the 3 bolts in the sequence shown in the illustration.
| 9. INSTALL REAR SEAT ASSEMBLY RH |
![]() |
Insert the 2 location pins through the 2 body holes and install the rear seat.
Using "TORX" socket wrench E10, install the 4 bolts in the sequence shown in the illustration.
![]() |
Install the rear seat cushion.
Using "TORX" socket wrench E10, install the 2 bolts in the sequence shown in the illustration.
| 10. INSTALL NO. 2 REAR SEAT LEG COVER |
![]() |
Engage the 3 claws and install the No. 2 rear seat leg cover.
| 11. INSTALL NO. 1 REAR SEAT LEG COVER |
for RH Side:
Install the No. 1 rear seat leg cover .
for LH Side:
Install the No. 1 rear seat leg cover .
| 12. INSTALL DECK FLOOR BOX RH (w/ Deck Board) |
![]() |
Set the deck floor box and lock the 2 knobs.
| 13. INSTALL DECK FLOOR BOX LH (w/ Deck Board) |
| 14. INSTALL SPARE WHEEL COVER ASSEMBLY (w/ Deck Board) |
![]() |
Install the spare wheel cover.
| 15. INSTALL DECK BOARD SUB-ASSEMBLY (w/ Deck Board) |
![]() |
Set the deck board and lock the 2 knobs.
| 16. INSTALL REAR FLOOR CARPET ASSEMBLY (w/o Deck Board) |
![]() |
Install the rear floor carpet.
| 17. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Package Tray Trim) |
![]() |
Engage the 2 claws and install the package tray trim panel.
Install the 5 pieces of hook tape.
Install the 2 package tray trim suspenders.
| 18. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 19. INSPECT SRS WARNING LIGHT |