Home › BODY ELECTRICAL › AUDIO / VISUAL › AUDIO AND VISUAL SYSTEM

AUDIO AND VISUAL SYSTEM > Speaker Circuit

for Preparation Click here


DESCRIPTION

Sound signals that have been amplified by the stereo component amplifier are sent to the speakers from the radio receiver through this circuit. If there is a short in this circuit, the sound cannot be heard from the speakers even though there is no malfunction in the speakers.

WIRING DIAGRAM


E118196E08


INSPECTION PROCEDURE

1.CHECK SPEAKER
  1. Check whether sounds is emitted from the speakers.
    Result
    Proceed to
    Front No. 1 speakers have problems
    A
    Rear speakers have problems
    B



B
Go to step 4
A


2.INSPECT FRONT NO. 1 SPEAKERS
  1. Check the left and right front No. 1 speakers.

    HINT:
    1. for HATCHBACK (Click here )
    2. for SEDAN (Click here )

    OK:
    Front No. 1 speakers are normal.



NG
REPLACE FRONT NO. 1 SPEAKER
OK


3.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - FRONT NO. 1 SPEAKER)
  1. Disconnect the D10 radio receiver connector.

  1. Disconnect the G6 or F6 front No. 1 speaker connector.



    I044961E04
  1. Measure the resistance.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D10-2 (FL+) - G6-1
    Always
    Below 1 Ω
    D10-6 (FL-) - G6-2
    Always
    Below 1 Ω
    D10-2 (FL+) - Body ground
    Always
    10 kΩ or higher
    D10-6(FL-) - Body ground
    Always
    10 kΩ or higher
    D10-1 (FR+) - F6-1
    Always
    Below 1 Ω
    D10-5 (FR-) - F6-2
    Always
    Below 1 Ω
    D10-1 (FR+) - Body ground
    Always
    10 kΩ or higher
    D10-1 (FR+) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

4.INSPECT REAR SPEAKERS
  1. Check the left and right rear No. 1 speakers.

    HINT:
    1. for 5Dr HATCHBACK (Click here )
    2. for 3Dr HATCHBACK (Click here )
    3. for SEDAN (Click here )

    OK:
    Rear No. 1 speakers are normal.



NG
REPLACE REAR SPEAKER
OK


5.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - REAR SPEAKER)
  1. Disconnect the D11 radio receiver connector.

  1. Disconnect the J27, J26, I4 or H4 rear speaker connectors.



  1. for HATCHBACK:



      I043620E03
    1. Measure the resistance.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      D11-2 (RL+) - J27-1 (I4-1)
      Always
      Below 1 Ω
      D11-6 (RL-) - J27-2 (I4-2)
      Always
      Below 1 Ω
      D11-2 (RL+) - Body ground
      Always
      10 kΩ or higher
      D11-6 (RL-) - Body ground
      Always
      10 kΩ or higher
      D11-1 (RR+) - J26-1 (H4-1)
      Always
      Below 1 Ω
      D11-3 (RR-) - J26-2 (H4-2)
      Always
      Below 1 Ω
      D11-1 (RR+) - Body ground
      Always
      10 kΩ or higher
      D11-3 (RR-) - Body ground
      Always
      10 kΩ or higher



  1. for SEDAN:



      C141219E01
    1. Measure the resistance.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      D11-2 (RL+) - J46-1
      Always
      Below 1 Ω
      D11-6 (RL-) - J46-2
      Always
      Below 1 Ω
      D11-2 (RL+) - Body ground
      Always
      10 kΩ or higher
      D11-6 (RL-) - Body ground
      Always
      10 kΩ or higher
      D11-1 (RR+) - J45-1
      Always
      Below 1 Ω
      D11-3 (RR-) - J45-2
      Always
      Below 1 Ω
      D11-1 (RR+) - Body ground
      Always
      10 kΩ or higher
      D11-3 (RR-) - Body ground
      Always
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)